Installation Manual
Page 1
KVT-719DVD KVT-739DVD MONITOR WITH DVD RECEIVER INSTALLATION MANUAL MONITOR CON RECEPTOR DVD MANUAL DE INSTALACIÓN © B54-4513-00/00 (KV/RV)
KVT-719DVD KVT-739DVD MONITOR WITH DVD RECEIVER INSTALLATION MANUAL MONITOR CON RECEPTOR DVD MANUAL DE INSTALACIÓN © B54-4513-00/00 (KV/RV)
Installation Manual
Page 3
...If the console has a lid, make sure the wires aren't touching to any metal part in your car's ignition does not have been activated. Installation Procedure 1. To prevent a short circuit, remove the key from the ignition wire (red) and the battery wire (yellow). Make the proper input ... turned ON (or it is 30° or less. Connect the wiring harness connector to a rear output terminal. • After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. Always connect those wires to a power source that in the following order: ground, battery, ignition...
...If the console has a lid, make sure the wires aren't touching to any metal part in your car's ignition does not have been activated. Installation Procedure 1. To prevent a short circuit, remove the key from the ignition wire (red) and the battery wire (yellow). Make the proper input ... turned ON (or it is 30° or less. Connect the wiring harness connector to a rear output terminal. • After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. Always connect those wires to a power source that in the following order: ground, battery, ignition...
Installation Manual
Page 8
... the sems bolts 7. Sems bolts (M4 × 8 mm) (Accessory 7) Installation brackets (Accessory 9) 2. Accessory 5 Make sure that the unit is unstable, it in place. If the unit is installed securely in place. Use the tapping screw 8 to secure the receiver unit to ...the sides of the mounting sleeve with a screwdriver or similar utensil and attach it may malfunction (eg, the sound may skip). Tapping screw (ø4 × 16 mm) (Accessory 8) 8 | KVT-719DVD/KVT-739DVD Attach the installation...
... the sems bolts 7. Sems bolts (M4 × 8 mm) (Accessory 7) Installation brackets (Accessory 9) 2. Accessory 5 Make sure that the unit is unstable, it in place. If the unit is installed securely in place. Use the tapping screw 8 to secure the receiver unit to ...the sides of the mounting sleeve with a screwdriver or similar utensil and attach it may malfunction (eg, the sound may skip). Tapping screw (ø4 × 16 mm) (Accessory 8) 8 | KVT-719DVD/KVT-739DVD Attach the installation...
Installation Manual
Page 10
Use only the screws provided. If you could damage the unit. 10 | KVT-719DVD/KVT-739DVD Installing in Japanese-made Cars Installation on Toyota, Nissan or Mitsubishi Car using Brackets at Holes shown by "●" or Accessory 0 (M5x6mm) or Accessory ! (M5x7mm) Car Bracket Accessory 0 (M5x6mm) or Accessory ! (M5x7mm) Screws (included in audio unit package) Audio unit or others Screws (included in audio unit package) ⁄ • Do not use the wrong screws, you use your own screws.
Use only the screws provided. If you could damage the unit. 10 | KVT-719DVD/KVT-739DVD Installing in Japanese-made Cars Installation on Toyota, Nissan or Mitsubishi Car using Brackets at Holes shown by "●" or Accessory 0 (M5x6mm) or Accessory ! (M5x7mm) Car Bracket Accessory 0 (M5x6mm) or Accessory ! (M5x7mm) Screws (included in audio unit package) Audio unit or others Screws (included in audio unit package) ⁄ • Do not use the wrong screws, you use your own screws.
Installation Manual
Page 11
Bend each end of installation bracket to fix the bracket. English | 11 Mount the bracket at two holes of the right and left unit sides. 1. Accessory 0 (M5x6mm) Screws (included in audio unit package) 2. Accessory 0 (M5x6mm) Car Bracket Screws (included in audio unit package) Use a flat-blade screwdriver or pliers, and bend each side. Installation on Toyota Car using Brackets at Holes shown by "●" or When using the bracket shown above, you cannot use screws at each case tab into the hole of case to fix the bracket.
Bend each end of installation bracket to fix the bracket. English | 11 Mount the bracket at two holes of the right and left unit sides. 1. Accessory 0 (M5x6mm) Screws (included in audio unit package) 2. Accessory 0 (M5x6mm) Car Bracket Screws (included in audio unit package) Use a flat-blade screwdriver or pliers, and bend each side. Installation on Toyota Car using Brackets at Holes shown by "●" or When using the bracket shown above, you cannot use screws at each case tab into the hole of case to fix the bracket.