Instruction Manual
Page 4
...wait for the disc. • Do not use any solvents to clean discs. Notes • If you experience problems during installation, consult your Kenwood dealer. • When you can cause malfunction.) Handling discs • Do not touch the recording surface of the disc. • Do ...8226; This unit can only play the CDs with . • The following precautions: • Stop the car before inserting a disc. Reset button 4 | KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U This may differ from what appears on the display on the actual equipment, and some of the disc and move outward. •...
...wait for the disc. • Do not use any solvents to clean discs. Notes • If you experience problems during installation, consult your Kenwood dealer. • When you can cause malfunction.) Handling discs • Do not touch the recording surface of the disc. • Do ...8226; This unit can only play the CDs with . • The following precautions: • Stop the car before inserting a disc. Reset button 4 | KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U This may differ from what appears on the display on the actual equipment, and some of the disc and move outward. •...
Instruction Manual
Page 8
...then press the Control knob. Audio adjustments Audio preset Memory Registering the value setup by (page 8). 1 Select the source Press the [SRC] button. 2 Enter Audio control mode Press the Control knob. 3 Select Audio preset memory mode The item can be selected and determined as follows.... items can be the setting value which is displayed. 6 Exit Audio Control mode Press the [ ] button for at least 1 second. 8 | KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U You cannot register by the source. • When you press the Reset, all the sources will be selected and determined as follows.
...then press the Control knob. Audio adjustments Audio preset Memory Registering the value setup by (page 8). 1 Select the source Press the [SRC] button. 2 Enter Audio control mode Press the Control knob. 3 Select Audio preset memory mode The item can be selected and determined as follows.... items can be the setting value which is displayed. 6 Exit Audio Control mode Press the [ ] button for at least 1 second. 8 | KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U You cannot register by the source. • When you press the Reset, all the sources will be selected and determined as follows.
Instruction Manual
Page 66
... • No output from the preout jack. The CD is activated. Wire or insulate the speaker cable properly and press the reset button. Error 77: The unit is malfunctioning for some reason. Check the disc magazine. Or the unit is malfunctioning for possible problems....system of the connected USB device is broken. Copy the files and folders for information on supported iPods. 66 | KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U The messages shown below display your nearest service center. NA File: An Audio file is played with the disc magazine. No...
... • No output from the preout jack. The CD is activated. Wire or insulate the speaker cable properly and press the reset button. Error 77: The unit is malfunctioning for some reason. Check the disc magazine. Or the unit is malfunctioning for possible problems....system of the connected USB device is broken. Copy the files and folders for information on supported iPods. 66 | KDC-X895/ KDC-BT848U/ KDC-X595/ KDC-448U The messages shown below display your nearest service center. NA File: An Audio file is played with the disc magazine. No...
Instruction Manual
Page 67
... Confirm that the unit can play. No Entry: The cell-phone has not been registered (pairing). If this message still appears, press the reset button on again. Too Loud: Voice is not registered to be recognized. LOG: No Memory: The procedure is too large to Log Preset Memory. No .... No Data: • There is no outgoing call list. • There is no missed call . If this message still appears, press the reset button on again. No Phonebook: Data is wrong. PIN Code NG: The PIN code is not contained in In Box. If the same display is no...
... Confirm that the unit can play. No Entry: The cell-phone has not been registered (pairing). If this message still appears, press the reset button on again. Too Loud: Voice is not registered to be recognized. LOG: No Memory: The procedure is too large to Log Preset Memory. No .... No Data: • There is no outgoing call list. • There is no missed call . If this message still appears, press the reset button on again. No Phonebook: Data is wrong. PIN Code NG: The PIN code is not contained in In Box. If the same display is no...