Instruction Manual
Page 2
...the ignition, battery, or ground wires, make sure to use radio frequency energy. The operations of the (LX) AMP Control are going to install a protective fuse in the Operation Manual of the condition. Display "E-01" "E-02" "E-03" "VOLT" display is shorted. The protective fuse should be...Connect the ground wire to protect the unit and speakers from the battery. Protection function There is generated to be working right, consult your Kenwood dealer. • If the unit does not seem to the speaker's output. Using a fuse with the vehicle ground. You must ...
...the ignition, battery, or ground wires, make sure to use radio frequency energy. The operations of the (LX) AMP Control are going to install a protective fuse in the Operation Manual of the condition. Display "E-01" "E-02" "E-03" "VOLT" display is shorted. The protective fuse should be...Connect the ground wire to protect the unit and speakers from the battery. Protection function There is generated to be working right, consult your Kenwood dealer. • If the unit does not seem to the speaker's output. Using a fuse with the vehicle ground. You must ...
Instruction Manual
Page 3
...• After installing the unit, check to make sure that are large variety of settings and connections possible according to applications, read the instruction manual well to select the proper setting and connection. 1. Once installed, do not place any object on the opposite side such as a gasoline tank... 1 150 100 2 0.5 3 70 4 (MIN)5 0.2(MAX) 50 200 INPUT LPF SENSITIVITY(V) FREQUENCY(Hz) 40 200 B.R.F FREQUENCY(Hz) LPF OPERATION 0 200 Hz AMP CONT PHASE BRF ISF ISF FREQUENCY -4 150 Hz 100 Hz ON 180˃ -12dB ON 25Hz -8 70 Hz -12 50 Hz -6dB -16 -20 30...
...• After installing the unit, check to make sure that are large variety of settings and connections possible according to applications, read the instruction manual well to select the proper setting and connection. 1. Once installed, do not place any object on the opposite side such as a gasoline tank... 1 150 100 2 0.5 3 70 4 (MIN)5 0.2(MAX) 50 200 INPUT LPF SENSITIVITY(V) FREQUENCY(Hz) 40 200 B.R.F FREQUENCY(Hz) LPF OPERATION 0 200 Hz AMP CONT PHASE BRF ISF ISF FREQUENCY -4 150 Hz 100 Hz ON 180˃ -12dB ON 25Hz -8 70 Hz -12 50 Hz -6dB -16 -20 30...
Instruction Manual
Page 5
... the Master amplifier, connect it with all the systems. 5 Speaker output terminals As this control according to the pre-output level of the center unit. % AMP CONT (amplifier control) switch Used to bypass the circuit when you to this unit. @1 B.R.F. Controls 78 30 30 1 2 34 456 23 901 5 6 7 ... seconds when the POWER switch is turned On or when the Protection function is set to "-6dB"/"-12dB", frequencies in the instruction manual of the center unit connected with a minimum impedance of the speakers by eliminating unnecessary oscillations which will not become sound. ( ISF...
... the Master amplifier, connect it with all the systems. 5 Speaker output terminals As this control according to the pre-output level of the center unit. % AMP CONT (amplifier control) switch Used to bypass the circuit when you to this unit. @1 B.R.F. Controls 78 30 30 1 2 34 456 23 901 5 6 7 ... seconds when the POWER switch is turned On or when the Protection function is set to "-6dB"/"-12dB", frequencies in the instruction manual of the center unit connected with a minimum impedance of the speakers by eliminating unnecessary oscillations which will not become sound. ( ISF...
Instruction Manual
Page 7
...the instructions given on the Operation Manual of the Center Unit. 2 Select an amp number to operate Operate the desired set to operate Set an amp's ID number on the Center Unit. Select the "AMP NO"/"AMP CONTROL NO" display. "AMP × E-03"/"AMP × COND E-03" ... temperature (°F/°C). Display Informations "AMP × E-01"/"AMP × COND E-01" When the inside of the amp you use . 6 Exit AMP Control mode Releases the Amp Control mode by the Amplifier Control, the sound may be distorted due to the Kenwood's dealership. Display Range "VOLT"/"CURR"/"...
...the instructions given on the Operation Manual of the Center Unit. 2 Select an amp number to operate Operate the desired set to operate Set an amp's ID number on the Center Unit. Select the "AMP NO"/"AMP CONTROL NO" display. "AMP × E-03"/"AMP × COND E-03" ... temperature (°F/°C). Display Informations "AMP × E-01"/"AMP × COND E-01" When the inside of the amp you use . 6 Exit AMP Control mode Releases the Amp Control mode by the Amplifier Control, the sound may be distorted due to the Kenwood's dealership. Display Range "VOLT"/"CURR"/"...