Kenwood 6202 - KAC Amplifier Support and Manuals
Get Help and Manuals for this Kenwood item
View All Support Options Below
Free Kenwood 6202 manuals!
Problems with Kenwood 6202?
Ask a Question
Free Kenwood 6202 manuals!
Problems with Kenwood 6202?
Ask a Question
Most Recent Kenwood 6202 Questions
I Have A 400w Car Amp With No Instalation Manual The Model Is Kac-6202 Can You M
(Posted by worz 11 years ago)
Popular Kenwood 6202 Manual Pages
Instruction Manual - Page 1
STEREO/BRIDGEABLE POWER AMPLIFIER
KAC-6202
INSTRUCTION MANUAL
© B64-3043-00/00 (MV)
Instruction Manual - Page 2
...; Do not touch the unit during installation, consult your Kenwood dealer.
• If the unit does not seem to be working right, consult your unit to malfunction. • To prevent a short circuit when replacing a fuse, first disconnect the wiring harness. Protection function There is a Protection function installed in the ACC ON position without turning...
Instruction Manual - Page 3
..., In a location that interferes with it. • When making a hole under the carpet. Install the amplifier in a place where
people, resins, and other damage. • Do not install near the dashboard, rear tray, or air bag safety parts. • The installation to the vehicle should securely fasten the unit to a place in which allows heat...
Instruction Manual - Page 4
... to the in the instruction manual of the center unit.
4 OPERATION switch This switch is not output.)
4 English Set to this unit, or to use as a high-power monaural amplifier. (The input right signal is used to select the operation mode of the amplifier.
• STEREO position: The amplifier can be used as a guide. Controls / Indicator
3
40...
Instruction Manual - Page 5
... your speakers from various accidents or problems that can occur. English 5 When the protection function is triggered, the Power indicator goes off and the amplifier stops operating. • When ...of trouble.
■ The protection function is activated in the following situations: This unit is equipped with a protection function for protecting this unit is not connected to a metal part serving ...
Instruction Manual - Page 6
...of the amplifier. With this terminal.
# Speaker level input terminals
NOTE
• The genuine-accessory car stereo shall have an impedance of the genuine-accessory car stereo is...output terminals • Stereo Connections: When you wish to use the unit as a highoutput monaural amplifier, bridged connections are used .
Otherwise malfunction may be no more than the maximum output of ...
Instruction Manual - Page 7
... short circuits. 2. ■ Installation procedure
Since there are large variety of settings and connections possible according to applications, read the instruction manual well to be connected should be... metal part of speakers having input power ratings that are touching the car body. Set the unit according to turn power off before changing the setting of the amplifier. Install the...
Instruction Manual - Page 8
... connector
Left
White
White/Black
Right
Gray
#
Gray/Black
Power control wire (Blue/ White)
@
GND
RCA cable ground terminal Speaker level input cable
Genuine-accessory car stereo (No line output center unit etc...
Instruction Manual - Page 9
■ Speaker wire connection (Stereo Connections) 00
Lead terminal*
(Bridged Connections) 0
25
* Commercially available parts Left speaker Right speaker
Speaker (Bridged)
25
■ Power wire connection
25
Terminal cover
789
Power control wire Battery wire*
Ground wire*
Protective Fuse*
Battery
Lead terminal*
English 9
Instruction Manual - Page 11
... low frequencies. (High pass)
C=
159000 fc x R
(µF)
L=
159 x R fc
(mH)
fc=Cut of Frequency (Hz) R=Speaker Impedance (Ω)
●Example: When it is required to set a crossover frequency of 120 Hz using a coil and capacitor...in a drop of the combined impedance with the closest ratings to the results calculated from the...
Instruction Manual - Page 12
... or miswiring. Troubleshooting Guide
What might appear to be a malfunction in your unit may just be the result of the terminals and wires
well.
• A speaker wire is pinched by a screw • Connect the speaker wire again so
in the car body.
The output level is distorted.) with wrong + /-polarity.
+ / -
Before calling service, first...
Instruction Manual - Page 13
...(4 Ω) (1 kHz, 0.8 % THD)...200 W x 1 Frequency Response (+0, -3 dB) ...10 Hz - 45 kHz Sensitivity (rated output) (MAX.) ...0.2 V Sensitivity (rated output) (MIN.) ...5.0 V Signal to change without notice. Specifications
Specifications subject to Noise Ratio...100 dB Input Impedance...10 kΩ Low Pass Filter Frequency (12 dB/oct.) ...50 - 200 Hz (variable) High Pass Filter Frequency (...
Kenwood 6202 Reviews
We have not received any reviews for Kenwood yet.