Instruction Manual
Page 2
... prevent battery rise When the unit is used , calculate the combined impedance of the speakers and then connect suitable speakers to the amplifier. (KAC-9152D: 1Ω or greater, KAC-9102D/8152D/8102D: 2Ω or greater) 4Ω 4Ω 8 Ω 4Ω 4Ω 2 Ω Combined impedance 2 ...circuit when replacing a fuse, first disconnect the wiring harness. When the protection function is triggered, the Power indicator goes OFF and the amplifier stops operating. • When a speaker wire may cause your Kenwood dealer. • If the unit does not seem to be connected ...
... prevent battery rise When the unit is used , calculate the combined impedance of the speakers and then connect suitable speakers to the amplifier. (KAC-9152D: 1Ω or greater, KAC-9102D/8152D/8102D: 2Ω or greater) 4Ω 4Ω 8 Ω 4Ω 4Ω 2 Ω Combined impedance 2 ...circuit when replacing a fuse, first disconnect the wiring harness. When the protection function is triggered, the Power indicator goes OFF and the amplifier stops operating. • When a speaker wire may cause your Kenwood dealer. • If the unit does not seem to be connected ...
Instruction Manual
Page 4
... Car fuse box ACC Battery ■ Power wire and Speaker wire connection Power control wire Terminal cover Battery wire* Protective Fuse* Lead terminal* Subwoofer (L + R) Battery Ground wire* ■ Remote cable connection (KAC-9152D/8152D only) 2CAUTION • Before connecting the remote controller cables, always set the Bass boost level control to appropriate speaker...
... Car fuse box ACC Battery ■ Power wire and Speaker wire connection Power control wire Terminal cover Battery wire* Protective Fuse* Lead terminal* Subwoofer (L + R) Battery Ground wire* ■ Remote cable connection (KAC-9152D/8152D only) 2CAUTION • Before connecting the remote controller cables, always set the Bass boost level control to appropriate speaker...
Instruction Manual
Page 5
...., consult your Kenwood dealer. 2 Battery terminal 3 Ground terminal 4 Power control terminal Controls the unit ON/OFF. If the Power indicator does not light when the power is turned on, the protection function may be activated. Use the diagram on , the Power indicator lights. Setting this may result. 6 REMOTE terminal (KAC-9152D/8152D only) Connects...
...., consult your Kenwood dealer. 2 Battery terminal 3 Ground terminal 4 Power control terminal Controls the unit ON/OFF. If the Power indicator does not light when the power is turned on, the protection function may be activated. Use the diagram on , the Power indicator lights. Setting this may result. 6 REMOTE terminal (KAC-9152D/8152D only) Connects...
Instruction Manual
Page 6
... 9 terminal of amplifier ¡. Dual Mono Drive (Function of the KAC-9152D) CENTER UNIT Remote controller f , 2%-/4% ,).%/54 , 2%-/4% ,).%/54 g f g Subwoofer (2 Ω or higher) A Dual Mono Drive system is turned on. • Use a speaker having the 2Ω or higher impedance only. • To protect the electrical system from a short-circuiting, be used for more fine...
... 9 terminal of amplifier ¡. Dual Mono Drive (Function of the KAC-9152D) CENTER UNIT Remote controller f , 2%-/4% ,).%/54 , 2%-/4% ,).%/54 g f g Subwoofer (2 Ω or higher) A Dual Mono Drive system is turned on. • Use a speaker having the 2Ω or higher impedance only. • To protect the electrical system from a short-circuiting, be used for more fine...
Instruction Manual
Page 7
...; 1 (2 Ω) (100 Hz, 0.9 % THD)...900 W × 1 (KAC-9152D) (2 Ω) (100 Hz, 0.9 % THD)...850 W × 1 (KAC-9102D) (1 Ω) (100 Hz, 1.0 % THD)...900 W × 1 (KAC-9152D) KAC-8152D/8102D 1100 W 300 W × 1 550 W × 1 - Frequency ...Protection circuit may be set to Noise Ratio...≤96 dB Low Pass Filter Frequency (24 dB/oct.) ...50 - 200 Hz (variable) Infrasonic Filter Frequency (18 dB/oct.)...15 / 25 Hz Phase Inverter ...0° (Normal) / 180° (Reverse) Bass Boost Circuit...0 - 18 dB (variable) Bass Boost Frequency...40 - 100 Hz (variable) (KAC-9152D...
...; 1 (2 Ω) (100 Hz, 0.9 % THD)...900 W × 1 (KAC-9152D) (2 Ω) (100 Hz, 0.9 % THD)...850 W × 1 (KAC-9102D) (1 Ω) (100 Hz, 1.0 % THD)...900 W × 1 (KAC-9152D) KAC-8152D/8102D 1100 W 300 W × 1 550 W × 1 - Frequency ...Protection circuit may be set to Noise Ratio...≤96 dB Low Pass Filter Frequency (24 dB/oct.) ...50 - 200 Hz (variable) Infrasonic Filter Frequency (18 dB/oct.)...15 / 25 Hz Phase Inverter ...0° (Normal) / 180° (Reverse) Bass Boost Circuit...0 - 18 dB (variable) Bass Boost Frequency...40 - 100 Hz (variable) (KAC-9152D...