Kenwood X1200M Support Question
Kenwood X1200M Support Question
Find answers below for this question about Kenwood X1200M - Excelon Mono Subwoofer Amplifier.Need a Kenwood X1200M manual? We have 1 online manual for this item!
Question posted by bosshunter45 on February 4th, 2022
Protection Mode Amplifer Kenwood Excelon Mod X1200m
light is on protection mode, how fix it? thanks
Current Answers
Answer #1: Posted by SonuKumar on February 5th, 2022 7:16 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,615,400
Member since:
May 9th, 2021 Points: 16,615,400
How do I take my Kenwood out of Protect Mode?
Turn off the receiver and let it cool for a few hours; then try again. If the protection mode warning doesn't go away on its own, press the reset button. If that doesn't work, disconnect the power lead from your receiver for 30 seconds and then reconnect it. If it still doesn't work, it's time to take it to the dealer.
https://www.techwalla.com/articles/how-to-turn-off-protect-mode-on-my-kenwood-stereo-receiver
https://www.manualslib.com/products/Kenwood-X1200m-Excelon-Mono-Subwoofer-Amplifier-12507.html
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Kenwood X1200M Manual Pages
Owner's Manual (pdf) - Page 1
X1200M
CLASS D MONO POWER AMPLIFIER 7 page 2-7
INSTRUCTION MANUAL
AMPLIFICATEUR MONO CLASSE D 7 page 8-13
MODE D'EMPLOI
AMPLIFICADOR DE POTENCIA CLASE D MONOFÓNICO 7 página 14-19
MANUAL DE INSTRUCCIONES
Take the time to the model and serial numbers whenever you obtain the best performance from your new power amplifier. Model X1200M Serial number
US Residence Only
Register Online...
Owner's Manual (pdf) - Page 2
...If you experience problems during use because the surface of the car chassis that to which can cause blown fuses etc. &#...• Be sure the unit is triggered, the PROTECTION indicator lights and the amplifier stops operating. • When a speaker wire may...or strange smells, turn off the power immediately and consult your Kenwood dealer. • Do not touch the unit during installation, ...
Owner's Manual (pdf) - Page 3
... tank, brake pipe, or wiring harness, and be damaged.
• Install this order. 7. Install the amplifier in a place where people, resins, and other damage.
• Do not install near the dashboard, rear...that there is nothing hazardous on top of the unit.
• The surface temperature of the amplifier will not come into contact with driving, In a location that gets wet, In a dusty ...
Owner's Manual (pdf) - Page 4
...;2Ω)
When two subwoofers are touching the car body. Insert the conductor of any switch.
• If the fuse blows, check wires for shorts, then replace the fuse with the following thicknesses:
Battery wire and ground wire
AWG 4 - AWG 6
Speaker wire
AWG 8 - Protective Fuse*
Battery wire*
Terminal cover
WARNING
To prevent fire caused...
Owner's Manual (pdf) - Page 5
...)
CAUTION
• Before connecting the remote controller cables, always turn the Bass boost level knob all the way to the left . BATT.
Setting the Slave amplifier 1. GND
FUSE [30Ax3]
P.CON
Remote cable Remote controller
SPEAKER OUTPUT
REMOTE
RCA cable*
L R
LINE IN LINE OUT
CAUTION
• Before connecting the remote controller cables...
Owner's Manual (pdf) - Page 6
... consult your Kenwood dealer.
2 Battery terminal 3 Power control terminal
Controls the unit ON/OFF. This improves the reproduction performance of the speakers by a subwoofer speaker do not...MANAGEMENT indicator Lights this indicator when the internal temperature is high.
~ PROTECTION indicator Lights this indicator when the protection function is turned on, the Power indicator lights. NOTE
...
Owner's Manual (pdf) - Page 7
...function.
Troubleshooting Guide
What might appear to be a malfunction in the car body.
• The switches may be the result of slight ...and use lower volume. • After check the speaker cord and fixing the cause of the short,
replace the fuse. • Adjust...position.
• The speakers wire are disconnected. • Protection circuit may be activated. • Volume is too high....
Similar Questions
Bass Control Knob
Is there a specific bass control knob that works for my Kenwood KAC-8104D
Is there a specific bass control knob that works for my Kenwood KAC-8104D
(Posted by tylerklaassen85 2 years ago)
Not Pushing My Subs
If both blue and red light come on and it doesn't push the subs what should I do
If both blue and red light come on and it doesn't push the subs what should I do
(Posted by stephensont951 2 years ago)
How Do I Get My Amp Out Of Protect Mode
how do I get my amp out of protect mode.
how do I get my amp out of protect mode.
(Posted by Anonymous-167992 3 years ago)
Kenwood Kac-8152d
Hello, I recently bought this amplifier and it was tested befor purchase. I went to install it and i...
Hello, I recently bought this amplifier and it was tested befor purchase. I went to install it and i...
(Posted by Justincleverly 10 years ago)