Kenwood KAC9102D Support Question
Kenwood KAC9102D Support Question
Find answers below for this question about Kenwood KAC9102D - Amplifier.Need a Kenwood KAC9102D manual? We have 1 online manual for this item!
Question posted by Anonymous-167992 on March 22nd, 2021
How Do I Get My Amp Out Of Protect Mode
how do I get my amp out of protect mode.
Current Answers
Answer #1: Posted by techyagent on March 23rd, 2021 5:26 AM
techyagent
Member since:
June 17th, 2014 Points: 4,799,800
Member since:
June 17th, 2014 Points: 4,799,800
If you find that one pair of speaker wires or one speaker causes the amp to go into protect, disconnect all speakers from the other end of the wires and separate the wires so they can't touch. If the amp still goes into protect, you have a bad speaker wire or the wire is shorted to chassis ground.
Please check this video tutorial
Thanks
Techygirl
Related Kenwood KAC9102D Manual Pages
Instruction Manual - Page 1
SUBWOOFER POWER AMPLIFIER
KAC-9152D KAC-9102D KAC-8152D KAC-8102D
INSTRUCTION MANUAL
© B64-3010-00/00 (MV)
Instruction Manual - Page 2
... sure to use a power supply wiring wire and protective fuse of greater current-handling capacity than one set of...combined impedance of the speakers and then connect suitable speakers to the amplifier. (KAC-9152D: 1Ω or greater, KAC-9102D/8152D/8102D: 2Ω or greater)
4Ω
4Ω 8... the ground wire to a metal part of the car chassis that are going to be connected should be the...
Instruction Manual - Page 3
...side cover is nothing hazardous on top of the unit.
• The surface temperature of the amplifier will become hot during use. Self-tapping screw (ø2.6 × 12 mm)
English 3 ...place in the unit. 7.Attach the unit. 8.Install the remote controller. (KAC-9152D/8152D only) 9.Connect the negative -
Install the amplifier in a place where people, resins, and other damage.
• Do...
Instruction Manual - Page 4
...-accessory car stereo (No line output center unit etc.)
* Commercially available parts
Power control wire RCA cable*
Left input
Right input
Car fuse box ACC
Battery
■ Power wire and Speaker wire connection
Power control wire
Terminal cover Battery wire* Protective Fuse*
Lead terminal* Subwoofer (L + R)
Battery
Ground wire*
■ Remote cable connection (KAC-9152D...
Instruction Manual - Page 5
...KAC-9102D/8102D only) Sets the low frequency level to these terminals.
2CAUTION
The rated input of this unit, for this switch is set "180°" (Reverse) the speaker output phase is turned on, the protection function may result.
6 REMOTE terminal (KAC...genuine-accessory car stereo shall have a maximum power output of the center unit.
& BOOST LEVEL (Bass boost level) control (KAC-9152D/8152D ...
Instruction Manual - Page 6
... amplifier ¡.
If a cable is
incorrectly connected between · terminals of amplifiers ¡ and ™. Dual Mono Drive (Function of the KAC-9152D...amplifier ™.
2CAUTION • Always connect between 9 and · terminals of these amplifiers, the amplifier protection circuit is turned on. • Use a speaker having the 2Ω or higher impedance only. • To protect...
Instruction Manual - Page 7
...% THD)...500 W × 1 (2 Ω) (100 Hz, 0.9 % THD)...900 W × 1 (KAC-9152D) (2 Ω) (100 Hz, 0.9 % THD)...850 W × 1 (KAC-9102D) (1 Ω) (100 Hz, 1.0 % THD)...900 W × 1 (KAC-9152D)
KAC-8152D/8102D 1100 W
300 W × 1 550 W × 1
- POSSIBLE CAUSE • Input (or output) cables are disconnected. • Protection circuit may be activated. • Volume is too high...
Similar Questions
Protection Mode Amplifer Kenwood Excelon Mod X1200m
light is on protection mode, how fix it? thanks
light is on protection mode, how fix it? thanks
(Posted by bosshunter45 2 years ago)
Why Our What
why is my kenwood kac-9102d amp light keep turning on and shutting back off I hook up the positive t...
why is my kenwood kac-9102d amp light keep turning on and shutting back off I hook up the positive t...
(Posted by Vegaliveslife13 4 years ago)
My Amp Won't Play Subs.
my kenwood 9102d amp won't play subs anymore. It's worked fine for over 2 years. I have not added or...
my kenwood 9102d amp won't play subs anymore. It's worked fine for over 2 years. I have not added or...
(Posted by falkonj5 7 years ago)
The Two Little Swtches On The Bottom Right Front Of My Amp. I Think One Of Them
what do the two swithes on the bottom rite front of my amp do? what should they be set at
what do the two swithes on the bottom rite front of my amp do? what should they be set at
(Posted by nathanraycraft 11 years ago)