Kenwood KAC9102D Support Question
Kenwood KAC9102D Support Question
Find answers below for this question about Kenwood KAC9102D - Amplifier.Need a Kenwood KAC9102D manual? We have 1 online manual for this item!
Question posted by nathanraycraft on February 18th, 2013
The Two Little Swtches On The Bottom Right Front Of My Amp. I Think One Of Them
what do the two swithes on the bottom rite front of my amp do? what should they be set at
Current Answers
Answer #1: Posted by quaff on February 19th, 2013 10:17 AM
quaff
Member since:
November 13th, 2011 Points: 537,590
Member since:
November 13th, 2011 Points: 537,590
The right most slider is labeled "PHASE" - this allows you to adjust for out-of-phase wiring or other out of phase situations. Explaining sound phasing is a whole other issue (try google if you really want to know), but as long as your system is wired correctly, this is not something you should have to worry about - leave it at 0.
The left switch is labeled "ISF". This is an Infrasonic filter switch. In brief, even sub-woofers can have issues replicating certain sounds below ~15Hz-25Hz or so. In an attempt to recreate these low frequencies it can start making odd sounds, distortion, or conflicting waves which might lead to phasing or other issues. This switch allows you to "cut off" below the selected frequency so the amp/sub will not reproduce anything below that frequency. Try the switch at 15Hz, if you notice you are having odd sounds issues with the sub, try it at 25Hz.
Related Kenwood KAC9102D Manual Pages
Instruction Manual - Page 1
SUBWOOFER POWER AMPLIFIER
KAC-9152D KAC-9102D KAC-8152D KAC-8102D
INSTRUCTION MANUAL
© B64-3010-00/00 (MV)
Instruction Manual - Page 2
... the ground wire to a metal part of the car chassis that acts as the unit's fuse capacity or...greater.)
• When more than one set of speakers are going to be connected should be working right, consult your Kenwood dealer. •...inside the unit. • If the unit starts to the amplifier. (KAC-9152D: 1Ω or greater, KAC-9102D/8152D/8102D: 2Ω or greater)
4Ω
4Ω 8...
Instruction Manual - Page 3
...
Installation procedure Since there are sensitive to select the proper setting and connection. 1.Remove the ignition key and disconnect the ...terminal)
1
Speaker level input cable
1
Hexagon Wrench
1
KAC-9152D/8152D only Part name
Remote cable
Remote controller
Mounting ... there is fixed and cannot be removed.
Install the amplifier in a place where people, resins, and other damage...
Instruction Manual - Page 4
...-accessory car stereo (No line output center unit etc.)
* Commercially available parts
Power control wire RCA cable*
Left input
Right input
Car fuse box ACC
Battery
■ Power wire and Speaker wire connection
Power control wire
Terminal cover Battery wire* Protective Fuse*
Lead terminal* Subwoofer (L + R)
Battery
Ground wire*
■ Remote cable connection (KAC-9152D...
Instruction Manual - Page 5
... input terminals
NOTE
• The genuine-accessory car stereo shall have a maximum power output of no less than 40 W.
• Do not connect the speaker output leads from a power amplifier (Optional) to the speaker level input terminals of trouble. (See page 2)
@ BASS BOOST LEVEL control (KAC-9102D/8102D only) Sets the low frequency level to a power...
Instruction Manual - Page 6
...; to avoid a high voltage from the vehicle in which 2 monaural amplifiers are both set amplifier ™ to the Reverse phase (PHASE: 180 º).
2.Set all other switches (except for more fine control if also connected to the 9 terminal of amplifier ¡. Dual Mono Drive (Function of the KAC-9152D)
CENTER UNIT Remote controller
f
, 2%-/4% ,).%/54
, 2%-/4% ,).%/54
g
f
g
Subwoofer...
Instruction Manual - Page 7
... in the car body. • The switches may just be set improperly.
• The Remote Cable is disconnected. • The "BOOST LEVEL" is set to the ...set to "0dB". SOLUTION • Connect the input (or output) cables. • Check connections by referring to change without notice. Audio Section...KAC-9152D/9102D Max Power Output...1800 W (KAC-9152D) Max Power Output...1700 W (KAC-9102D...
Similar Questions
How Do I Get My Amp Out Of Protect Mode
how do I get my amp out of protect mode.
how do I get my amp out of protect mode.
(Posted by Anonymous-167992 3 years ago)
Why Our What
why is my kenwood kac-9102d amp light keep turning on and shutting back off I hook up the positive t...
why is my kenwood kac-9102d amp light keep turning on and shutting back off I hook up the positive t...
(Posted by Vegaliveslife13 4 years ago)
My Amp Won't Play Subs.
my kenwood 9102d amp won't play subs anymore. It's worked fine for over 2 years. I have not added or...
my kenwood 9102d amp won't play subs anymore. It's worked fine for over 2 years. I have not added or...
(Posted by falkonj5 7 years ago)
Giving The Input ''music'' To My Amplifier, No Rca Cables (speaker To Amp)
Hi,I am installing a subwoofer in my 2014 Chevy Tahoe. I have no RCA cable to plug from my radio to ...
Hi,I am installing a subwoofer in my 2014 Chevy Tahoe. I have no RCA cable to plug from my radio to ...
(Posted by guillaumelongtin 8 years ago)
I Have A 400w Car Amp With No Instalation Manual The Model Is Kac-6202 Can You M
(Posted by worz 11 years ago)