Kenwood KAC-6202 Support Question
Kenwood KAC-6202 Support Question
Find answers below for this question about Kenwood KAC-6202.Need a Kenwood KAC-6202 manual? We have 1 online manual for this item!
Question posted by guillaumelongtin on September 21st, 2015
Giving The Input ''music'' To My Amplifier, No Rca Cables (speaker To Amp)
Hi,I am installing a subwoofer in my 2014 Chevy Tahoe. I have no RCA cable to plug from my radio to my amplifier (original radio in the car). A couple of years ago, I connected wires from my speaker to the amplifier to give the signal (or music) to the amplifier. My question is, where will it connect on this amplifier? Is it the speaker input level? If yes there are 4 wires (two white, two grey)... Thanks!
Current Answers
Answer #1: Posted by TechSupport101 on September 23rd, 2015 5:46 AM
TechSupport101
Member since:
May 24th, 2013 Points: 12,171,305
Member since:
May 24th, 2013 Points: 12,171,305
Please see the eHow AMP installation tutorial here http://www.ehow.com/how_5063694_install-amp-rca-jacks.html - it features NO use of the RCA jacks/cable.
Related Kenwood KAC-6202 Manual Pages
Instruction Manual - Page 1
STEREO/BRIDGEABLE POWER AMPLIFIER
KAC-6202
INSTRUCTION MANUAL
© B64-3043-00/00 (MV)
Instruction Manual - Page 2
...wires, make sure to use a new one with a 5 mm² (AWG 10) or more to prevent wire deterioration and damage to the wire... of Items
4
Terminal cover (Power terminal)
1
Speaker level input cable
1
2 English NOTE
• If you of the...connected to a 12V DC power
supply with a negative ground connection. • Do not open the top or bottom covers of the unit. • Do not install...
Instruction Manual - Page 3
...
English 3
Install the amplifier in a place where
people, resins, and other damage. • Do not install near the dashboard, rear tray, or air bag safety parts. • The installation to the...accident. • After installing the unit, check to make sure that electrical equipment such as a gasoline tank, brake pipe, or wiring harness, and be damaged. • Install this unit in a ...
Instruction Manual - Page 4
... as a stereo amplifier.
• MONO (Lch) position: Amplifies the signal input from the left side only. Set to this unit, or to the maximum power output of the genuineaccessory car stereo.
NOTE
For...
34
1 FILTER switch This switch allows to apply high-pass or low-pass filtering to the speaker outputs. • HPF (High-Pass Filter) position: The filter outputs the band of higher frequencies...
Instruction Manual - Page 5
.... When the protection function is triggered, the Power indicator goes off and the amplifier stops operating. • When a speaker wire may be short-circuited. • When a speaker output contacts ground. • When the unit malfunctions and a DC signal is sent to the speaker output. • When the internal temperature is high and unit won't operate...
Instruction Manual - Page 6
... of the genuine-accessory car stereo is 2Ω or greater for this terminal.
# Speaker level input terminals
NOTE
• The genuine-accessory car stereo shall have an impedance of the amplifier. When multiple speakers are to use the unit as a stereo amplifier, stereo connections are used .
LINE IN terminal
@ RCA cable ground lead terminal When using an RCA cable with all the...
Instruction Manual - Page 7
... the speaker or grounding speaker wires to the metal body of the car can cause blown fuses etc.
• If a buzzing noise is heard from the speakers when the engine is running, connect a line noise filter (optional) to each amplifier.
■ Speaker Selection
• The rated input power of the speakers that are going to be 2Ω or greater (for stereo connections...
Instruction Manual - Page 8
...Connection
■ RCA cable or Speaker level input connection (RCA cable Connections)
! RCA cable* @
CENTER UNIT (CD receiver, etc.)
Left input
Right input
(Speaker level input Connections)
Cable Color of the connector
Left
White
White/Black
Right
Gray
#
Gray/Black
Power control wire (Blue/ White)
@
GND
RCA cable ground terminal Speaker level input cable
Genuine-accessory car stereo...
Instruction Manual - Page 9
■ Speaker wire connection (Stereo Connections) 00
Lead terminal*
(Bridged Connections) 0
25
* Commercially available parts Left speaker Right speaker
Speaker (Bridged)
25
■ Power wire connection
25
Terminal cover
789
Power control wire Battery wire*
Ground wire*
Protective Fuse*
Battery
Lead terminal*
English 9
Instruction Manual - Page 11
... (µF) and the coil rating should be as close as possible to 5.3 (mH).
2CAUTION
• If you wish to bridge-connect a speaker, the speaker impedance must be no less than 4 ohms. Connecting a speaker with the subwoofer.
• Ensure that the withstand voltage and current ratings of 6dB/oct. slope
0 dB -3 dB
Crossover Frequency
L
C
Frequency
Coil (L): Passes...
Instruction Manual - Page 12
...and wires
well.
• A speaker wire is bad. • The speakers wire are
• Connect the input (or...car body.
Before calling service, first check the following table for possible problems.
PROBLEM
POSSIBLE CAUSE
SOLUTION
No sound.
• Input (or output) cables are connected • Connect them properly checking the
(The sound is shorted.
• After check the speaker...
Instruction Manual - Page 13
Specifications
Specifications subject to Noise Ratio...100 dB Input Impedance...10 kΩ Low Pass Filter Frequency (12 dB/oct.) ...50 - 200 Hz (variable) High Pass Filter Frequency (12 dB/oct.)...50 - 200 Hz (variable) ...
Similar Questions
Speaker Wiring
how how should I wire my 12" power acustic gothic speaker to my KAC 8105D amplifier . Just one speak...
how how should I wire my 12" power acustic gothic speaker to my KAC 8105D amplifier . Just one speak...
(Posted by fisch5050 2 years ago)
Technical Support
not getting no sound out of speaker Jacks with RCA jacks in amp hook you radio
not getting no sound out of speaker Jacks with RCA jacks in amp hook you radio
(Posted by mudddigger1981 4 years ago)
How To Fix Loose Rcas
Subs work fine if the volume is low, but when I turn it up they start cutting in and out. But if I p...
Subs work fine if the volume is low, but when I turn it up they start cutting in and out. But if I p...
(Posted by justindavis7491 7 years ago)
How To Adjust Speaker Level Inputs Kac 7202
(Posted by stooucmech 9 years ago)
Is There A Way To Test The Speaker Output Beside Connecting Speakers?
My sub woofer stopped bumping one day out of the blue. Amp has power, speakers are getting power cau...
My sub woofer stopped bumping one day out of the blue. Amp has power, speakers are getting power cau...
(Posted by hmaura 13 years ago)