Kenwood KAC-8152D Support Question
Kenwood KAC-8152D Support Question
Find answers below for this question about Kenwood KAC-8152D.Need a Kenwood KAC-8152D manual? We have 1 online manual for this item!
Question posted by Justincleverly on August 23rd, 2013
Kenwood Kac-8152d
Hello, I recently bought this amplifier and it was tested befor purchase. I went to install it and it would not power on. Power, ground and remote wire tested and working with other amp. I do not have an RCA ground wire. I have read the manual and checked the wires fuses both under the hood and on my amp. I believe it has gone into protective mode and there is no information on how to correct this issue. If you could tell me what to do to fix this or any information regarding this matter would be greatly appreciated. Thank you.
Current Answers
Answer #1: Posted by TommyKervz on August 24th, 2013 1:12 AM
TommyKervz
Member since:
January 10th, 2013 Points: 17,776,813
Member since:
January 10th, 2013 Points: 17,776,813
Greetings - On the link below are possible causes of Protection Mode and more
http://www.caraudioforum.com/showthread.php?t=335991
http://www.caraudioforum.com/showthread.php?t=335991
Related Kenwood KAC-8152D Manual Pages
Instruction Manual - Page 1
SUBWOOFER POWER AMPLIFIER
KAC-9152D KAC-9102D KAC-8152D KAC-8102D
INSTRUCTION MANUAL
© B64-3010-00/00 (MV)
Instruction Manual - Page 2
... the speakers and then connect suitable speakers to the amplifier. (KAC-9152D: 1Ω or greater, KAC-9102D/8152D/8102D: 2Ω or greater)
4Ω
4Ω 8 Ω
4Ω 4Ω 2 Ω
Combined impedance
2 English Cleaning the unit If the front panel gets dirty, turn the power on if the ground wire is connected to direct sunlight or excessive heat
or...
Instruction Manual - Page 3
... turn signal lamps and windshield wipers operate normally.
terminal of the amplifier will not obstruct driving. If the unit comes off due to ...wires of the units. 4.Connect the speaker wires. 5.Connect the power wire, power control wire and grounding wire following this
order. 6.Install the installation fittings in the unit. 7.Attach the unit. 8.Install the remote controller. (KAC-9152D/8152D...
Instruction Manual - Page 4
... car stereo (No line output center unit etc.)
* Commercially available parts
Power control wire RCA cable*
Left input
Right input
Car fuse box ACC
Battery
■ Power wire and Speaker wire connection
Power control wire
Terminal cover Battery wire* Protective Fuse*
Lead terminal* Subwoofer (L + R)
Battery
Ground wire*
■ Remote cable connection (KAC-9152D/8152D...
Instruction Manual - Page 5
...
• The genuine-accessory car stereo shall have a maximum power output of 2 ohms, connect speakers with this switch is set "180°" (Reverse) the speaker output phase is turned on, the protection function may result.
6 REMOTE terminal (KAC-9152D/8152D only) Connects the Remote cable.
If the Power indicator does not light when the power is reversed.
^ INPUT SENSITIVITY...
Instruction Manual - Page 6
...wire to the 9 terminal of amplifiers ¡ and ™. 3.The remote controller can
be sure to remove the · battery cable from peripherals.
6 English Also, connect the · speaker wire to the 9 terminal of amplifier ™.
2.Connect between 9 and · terminals of amplifiers... to amplifier ¡. Dual Mono Drive (Function of the KAC-9152D)
CENTER UNIT Remote controller
...
Instruction Manual - Page 7
... 180° (Reverse) 0 - 18 dB (variable) 40 - 100 Hz (variable) (KAC-8152D) 40 Hz (KAC-8102D)
General ...KAC-9152D/9102D Operating Voltage ...14.4 V (11 - 16 V allowable) Current Consumption ...60 A Installation Size (W × H × D) ...380 × 61 × 286 mm Weight ...5.8 kg (KAC-9152D) Weight ...5.7 kg (KAC-9102D)
KAC-8152D/8102D 14.4 V (11 - 16 V allowable) 40 A 380 × 61 ×...
Similar Questions
Protection Mode Amplifer Kenwood Excelon Mod X1200m
light is on protection mode, how fix it? thanks
light is on protection mode, how fix it? thanks
(Posted by bosshunter45 2 years ago)
Not Pushing My Subs
If both blue and red light come on and it doesn't push the subs what should I do
If both blue and red light come on and it doesn't push the subs what should I do
(Posted by stephensont951 2 years ago)
How Do I Get My Amp Out Of Protect Mode
how do I get my amp out of protect mode.
how do I get my amp out of protect mode.
(Posted by Anonymous-167992 3 years ago)
No Power To Kac-6104d Amp
The amp was working fine, but now the power light is off on the amp and the Kenwood head unit is off...
The amp was working fine, but now the power light is off on the amp and the Kenwood head unit is off...
(Posted by jwilliams644508 10 years ago)