Instruction Manual
Page 1
SUBWOOFER POWER AMPLIFIER KAC-9152D KAC-9102D KAC-8152D KAC-8102D INSTRUCTION MANUAL © B64-3010-00/00 (MV)
SUBWOOFER POWER AMPLIFIER KAC-9152D KAC-9102D KAC-8152D KAC-8102D INSTRUCTION MANUAL © B64-3010-00/00 (MV)
Instruction Manual
Page 2
... unit is not connected to a metal part serving as an electrical ground passing electricity to the battery's negative - Use it depletes the battery. Protection function The protection function is not connected. • Be sure to malfunction. • To prevent a short circuit when replacing a fuse, first disconnect the wiring harness. Using a fuse with the wrong rating may be greater than the maximum output power (in Watts) of 1Ω/ 2Ω or greater. Do not turn the power...
... unit is not connected to a metal part serving as an electrical ground passing electricity to the battery's negative - Use it depletes the battery. Protection function The protection function is not connected. • Be sure to malfunction. • To prevent a short circuit when replacing a fuse, first disconnect the wiring harness. Using a fuse with the wrong rating may be greater than the maximum output power (in Watts) of 1Ω/ 2Ω or greater. Do not turn the power...
Instruction Manual
Page 3
terminal of the battery to prevent short circuits. 2.Set the unit according to the intended usage. 3.Connect the input and output wires of the units. 4.Connect the speaker wires. 5.Connect the power wire, power control wire and grounding wire following this unit in which allows heat to select the proper setting and connection. 1.Remove the ignition key and disconnect the negative - Install the amplifier in a place where people, resins, and other damage. • Do not install near the...
terminal of the battery to prevent short circuits. 2.Set the unit according to the intended usage. 3.Connect the input and output wires of the units. 4.Connect the speaker wires. 5.Connect the power wire, power control wire and grounding wire following this unit in which allows heat to select the proper setting and connection. 1.Remove the ignition key and disconnect the negative - Install the amplifier in a place where people, resins, and other damage. • Do not install near the...
Instruction Manual
Page 4
...Color of the connector 9 White Left · White/Black 9 Gray Right · Gray/Black Genuine-accessory car stereo (No line output center unit etc.) * Commercially available parts Power control wire RCA cable* Left input Right input Car fuse box ACC Battery ■ Power wire and Speaker wire connection Power control wire Terminal cover Battery wire* Protective Fuse* Lead terminal* Subwoofer (L + R) Battery Ground wire* ■ Remote cable connection (KAC-9152D/8152D only) 2CAUTION • Before connecting the remote controller cables, always set the Bass boost...
...Color of the connector 9 White Left · White/Black 9 Gray Right · Gray/Black Genuine-accessory car stereo (No line output center unit etc.) * Commercially available parts Power control wire RCA cable* Left input Right input Car fuse box ACC Battery ■ Power wire and Speaker wire connection Power control wire Terminal cover Battery wire* Protective Fuse* Lead terminal* Subwoofer (L + R) Battery Ground wire* ■ Remote cable connection (KAC-9152D/8152D only) 2CAUTION • Before connecting the remote controller cables, always set the Bass boost...
Instruction Manual
Page 5
... be boosted. * FREQUENCY (Bass boost frequency) control (KAC-9152D/ 8152D only) Sets the center frequency around which can 't find the specified capacity fuse at your store etc., consult your Kenwood dealer. 2 Battery terminal 3 Ground terminal 4 Power control terminal Controls the unit ON/OFF. This improves the reproduction performance of the speakers by the ignition key switch (ACC line). Remove the cover to access to be compensated. # LPF(Low-Pass Filter) FREQUENCY control This control adjusts the frequency band output from this switch is set...
... be boosted. * FREQUENCY (Bass boost frequency) control (KAC-9152D/ 8152D only) Sets the center frequency around which can 't find the specified capacity fuse at your store etc., consult your Kenwood dealer. 2 Battery terminal 3 Ground terminal 4 Power control terminal Controls the unit ON/OFF. This improves the reproduction performance of the speakers by the ignition key switch (ACC line). Remove the cover to access to be compensated. # LPF(Low-Pass Filter) FREQUENCY control This control adjusts the frequency band output from this switch is set...
Instruction Manual
Page 6
... bridged mode to drive one subwoofer with a high-output signal. If a cable is incorrectly connected between 9 and · terminals of these amplifiers, the amplifier protection circuit is a system in advance. • Fully insulate amplifier terminals and speaker terminals to avoid a high voltage from the vehicle in which 2 monaural amplifiers are both set amplifier ™ to the Reverse phase (PHASE: 180 º). 2.Set all other switches (except for more fine control if also connected to amplifier...
... bridged mode to drive one subwoofer with a high-output signal. If a cable is incorrectly connected between 9 and · terminals of these amplifiers, the amplifier protection circuit is a system in advance. • Fully insulate amplifier terminals and speaker terminals to avoid a high voltage from the vehicle in which 2 monaural amplifiers are both set amplifier ™ to the Reverse phase (PHASE: 180 º). 2.Set all other switches (except for more fine control if also connected to amplifier...
Instruction Manual
Page 7
... speakers wire are disconnected. • Protection circuit may just be activated. • Volume is too high. • The speaker cord is shorted. • The input sensitivity adjusting control is not set to "0dB". Before calling service, first check the following table for possible problems. PROBLEM No sound. (Blown fuse.) The output level is distorted.) The Remote Controller does not function. of slight misoperation or miswiring. Frequency Response (+0, -3 dB)...5 Hz - 200 Hz Sensitivity (rated output) (MAX.) ...0.2 V Sensitivity (rated output...
... speakers wire are disconnected. • Protection circuit may just be activated. • Volume is too high. • The speaker cord is shorted. • The input sensitivity adjusting control is not set to "0dB". Before calling service, first check the following table for possible problems. PROBLEM No sound. (Blown fuse.) The output level is distorted.) The Remote Controller does not function. of slight misoperation or miswiring. Frequency Response (+0, -3 dB)...5 Hz - 200 Hz Sensitivity (rated output) (MAX.) ...0.2 V Sensitivity (rated output...