Instruction Manual
Page 1
SUBWOOFER POWER AMPLIFIER KAC-9152D KAC-9102D KAC-8152D KAC-8102D INSTRUCTION MANUAL © B64-3010-00/00 (MV)
SUBWOOFER POWER AMPLIFIER KAC-9152D KAC-9102D KAC-8152D KAC-8102D INSTRUCTION MANUAL © B64-3010-00/00 (MV)
Instruction Manual
Page 2
... battery wire for protecting this unit is not connected. • Be sure to install a protective fuse in Watts) of the amplifier. terminal. When more than one with the prescribed rating. Cleaning the unit If the front panel gets dirty, turn off . Use it depletes the battery. Use of speakers having input power ratings that are going to be working right, consult your unit to malfunction. • To prevent a short circuit when replacing a fuse, first disconnect the wiring harness...
... battery wire for protecting this unit is not connected. • Be sure to install a protective fuse in Watts) of the amplifier. terminal. When more than one with the prescribed rating. Cleaning the unit If the front panel gets dirty, turn off . Use it depletes the battery. Use of speakers having input power ratings that are going to be working right, consult your unit to malfunction. • To prevent a short circuit when replacing a fuse, first disconnect the wiring harness...
Instruction Manual
Page 3
... during use. terminal of the battery to prevent short circuits. 2.Set the unit according to the intended usage. 3.Connect the input and output wires of the battery. 2CAUTION • Do not install in the below locations; (Unstable location, In a location that interferes with it may be damaged. • Install this order. 6.Install the installation fittings in the unit. 7.Attach the unit. 8.Install the remote controller. (KAC-9152D/8152D only) 9.Connect the negative - Install the amplifier...
... during use. terminal of the battery to prevent short circuits. 2.Set the unit according to the intended usage. 3.Connect the input and output wires of the battery. 2CAUTION • Do not install in the below locations; (Unstable location, In a location that interferes with it may be damaged. • Install this order. 6.Install the installation fittings in the unit. 7.Attach the unit. 8.Install the remote controller. (KAC-9152D/8152D only) 9.Connect the negative - Install the amplifier...
Instruction Manual
Page 4
.../Black 9 Gray Right · Gray/Black Genuine-accessory car stereo (No line output center unit etc.) * Commercially available parts Power control wire RCA cable* Left input Right input Car fuse box ACC Battery ■ Power wire and Speaker wire connection Power control wire Terminal cover Battery wire* Protective Fuse* Lead terminal* Subwoofer (L + R) Battery Ground wire* ■ Remote cable connection (KAC-9152D/8152D only) 2CAUTION • Before connecting the remote controller cables, always set the Bass boost level control to appropriate speaker connectors...
.../Black 9 Gray Right · Gray/Black Genuine-accessory car stereo (No line output center unit etc.) * Commercially available parts Power control wire RCA cable* Left input Right input Car fuse box ACC Battery ■ Power wire and Speaker wire connection Power control wire Terminal cover Battery wire* Protective Fuse* Lead terminal* Subwoofer (L + R) Battery Ground wire* ■ Remote cable connection (KAC-9152D/8152D only) 2CAUTION • Before connecting the remote controller cables, always set the Bass boost level control to appropriate speaker connectors...
Instruction Manual
Page 5
... using an RCA cable with 2-ohms or higher impedance to these terminals. 2CAUTION The rated input of trouble. (See page 2) @ BASS BOOST LEVEL control (KAC-9102D/8102D only) Sets the low frequency level to "15 Hz" or "25 Hz" cuts the frequencies below the respective frequency. Power indicator When the power is output. ! Setting this unit, or to the maximum power output of the center unit connected with this switch to be compensated. # LPF(Low-Pass Filter) FREQUENCY control This control adjusts the frequency band output from the line input terminal...
... using an RCA cable with 2-ohms or higher impedance to these terminals. 2CAUTION The rated input of trouble. (See page 2) @ BASS BOOST LEVEL control (KAC-9102D/8102D only) Sets the low frequency level to "15 Hz" or "25 Hz" cuts the frequencies below the respective frequency. Power indicator When the power is output. ! Setting this unit, or to the maximum power output of the center unit connected with this switch to be compensated. # LPF(Low-Pass Filter) FREQUENCY control This control adjusts the frequency band output from the line input terminal...
Instruction Manual
Page 6
... "PHASE" switch) of the KAC-9152D) CENTER UNIT Remote controller f , 2%-/4% ,).%/54 , 2%-/4% ,).%/54 g f g Subwoofer (2 Ω or higher) A Dual Mono Drive system is turned on. • Use a speaker having the 2Ω or higher impedance only. • To protect the electrical system from a short-circuiting, be used just when connected to avoid a high voltage from peripherals. 6 English Connection 1.Connect the 9 speaker wire to amplifier ™. 2CAUTION • Always connect between · terminals of these amplifiers, the amplifier protection circuit is...
... "PHASE" switch) of the KAC-9152D) CENTER UNIT Remote controller f , 2%-/4% ,).%/54 , 2%-/4% ,).%/54 g f g Subwoofer (2 Ω or higher) A Dual Mono Drive system is turned on. • Use a speaker having the 2Ω or higher impedance only. • To protect the electrical system from a short-circuiting, be used just when connected to avoid a high voltage from peripherals. 6 English Connection 1.Connect the 9 speaker wire to amplifier ™. 2CAUTION • Always connect between · terminals of these amplifiers, the amplifier protection circuit is...
Instruction Manual
Page 7
... for possible problems. PROBLEM No sound. (Blown fuse.) The output level is distorted.) The Remote Controller does not function. of the terminals and wires well. • Connect the speaker wire again so that it is not pinched by anything. • Set switches properly by referring to change without notice. Specifications Specifications subject to . • Connect the Remote Cable securely and correctly. • Adjust the "BOOST LEVEL". Frequency Response (+0, -3 dB)...5 Hz - 200 Hz Sensitivity (rated output) (MAX.) ...0.2 V Sensitivity (rated output) (MIN.) ...5.0 V Input Impedance...
... for possible problems. PROBLEM No sound. (Blown fuse.) The output level is distorted.) The Remote Controller does not function. of the terminals and wires well. • Connect the speaker wire again so that it is not pinched by anything. • Set switches properly by referring to change without notice. Specifications Specifications subject to . • Connect the Remote Cable securely and correctly. • Adjust the "BOOST LEVEL". Frequency Response (+0, -3 dB)...5 Hz - 200 Hz Sensitivity (rated output) (MAX.) ...0.2 V Sensitivity (rated output) (MIN.) ...5.0 V Input Impedance...