Instruction Manual
Page 4
... the prescribed rating. If the liquid crystal fluid from the LCD contacts your body or clothing, wash it off the power immediately and consult your Kenwood dealer. • Make sure not to get your fingers caught between the faceplate and the unit. • Be careful not to drop the unit ...or subject it may cause your unit to malfunction. • To prevent a short circuit when replacing a fuse, first disconnect the wiring harness. • Do not place any object between the faceplate and the unit. • Do not apply excessive force to your fingers. • Do not subject...
... the prescribed rating. If the liquid crystal fluid from the LCD contacts your body or clothing, wash it off the power immediately and consult your Kenwood dealer. • Make sure not to get your fingers caught between the faceplate and the unit. • Be careful not to drop the unit ...or subject it may cause your unit to malfunction. • To prevent a short circuit when replacing a fuse, first disconnect the wiring harness. • Do not place any object between the faceplate and the unit. • Do not apply excessive force to your fingers. • Do not subject...
Instruction Manual
Page 29
...your car. 7. To prevent a short circuit, remove the key from the ignition and disconnect the - Connect the wiring harness wires in turn may die. • If the console has a lid, make sure the wires aren't touching to ...the ignition key. If you connect the + connector of the wiring harness. 4. battery. 2. Accessories/ Installation Procedure Accessories 1 2 3 4 5 6 7 ..........1 ..........2 ..........4 ..........4 ..........1 ..........1 ..........2 Installation Procedure 1. Connect the wiring harness connector to a front output terminal, do not mix front and rear).
...your car. 7. To prevent a short circuit, remove the key from the ignition and disconnect the - Connect the wiring harness wires in turn may die. • If the console has a lid, make sure the wires aren't touching to ...the ignition key. If you connect the + connector of the wiring harness. 4. battery. 2. Accessories/ Installation Procedure Accessories 1 2 3 4 5 6 7 ..........1 ..........2 ..........4 ..........4 ..........1 ..........1 ..........2 Installation Procedure 1. Connect the wiring harness connector to a front output terminal, do not mix front and rear).
Instruction Manual
Page 30
...Connect either the telephone rings or during conversation. To "EXT.AMP.CONT." To connect the KENWOOD navigation system, consult your navigation manual. To car light control switch Wiring harness (Accessory1) P.CONT Power control/Motor antenna control wire (Blue/White) MUTE Mute wire ... manuals. ANT. AUX Connecting Wires to Terminals Ez500 A Aux input A B Front output C Rear output/ Subwoofer output B Left output (White), Right output (Red) FRONT To KENWOOD disc changer/ Sirius satellite radio tuner/ HD Radio tuner/ External optional accessory To connect these leads...
...Connect either the telephone rings or during conversation. To "EXT.AMP.CONT." To connect the KENWOOD navigation system, consult your navigation manual. To car light control switch Wiring harness (Accessory1) P.CONT Power control/Motor antenna control wire (Blue/White) MUTE Mute wire ... manuals. ANT. AUX Connecting Wires to Terminals Ez500 A Aux input A B Front output C Rear output/ Subwoofer output B Left output (White), Right output (Red) FRONT To KENWOOD disc changer/ Sirius satellite radio tuner/ HD Radio tuner/ External optional accessory To connect these leads...
Instruction Manual
Page 34
... when the ignition is connected to one with one side. ☞ Center the fader and balance settings. ✔ The input/output wires or wiring harness are incorrectly connected. ☞ Connect the wire correctly, referring to the section on 'Audio Setup' (page 11). ✔ The 'Built-in Tuner... turned OFF. ✔ The ignition and battery wire are connected incorrectly. ☞ Reconnect the input/output wires or the wiring harness correctly. Radio reception is poor. ✔ The car antenna is not extended. ☞ Pull the antenna out all the way to a different speaker. ?
... when the ignition is connected to one with one side. ☞ Center the fader and balance settings. ✔ The input/output wires or wiring harness are incorrectly connected. ☞ Connect the wire correctly, referring to the section on 'Audio Setup' (page 11). ✔ The 'Built-in Tuner... turned OFF. ✔ The ignition and battery wire are connected incorrectly. ☞ Reconnect the input/output wires or the wiring harness correctly. Radio reception is poor. ✔ The car antenna is not extended. ☞ Pull the antenna out all the way to a different speaker. ?