Icom IC-M424G Support and Manuals
Get Help and Manuals for this Icom item
View All Support Options Below
Free Icom IC-M424G manuals!
Problems with Icom IC-M424G?
Ask a Question
Free Icom IC-M424G manuals!
Problems with Icom IC-M424G?
Ask a Question
Popular Icom IC-M424G Manual Pages
Instruction Manual - Page 2
...-in GPS *
*For only IC-M323G and IC-M324G.
i
IMPORTANT
READ ALL INSTRUCTIONS carefully and completely
before using the optional MA-500TR Class B AIS Transponder
❍ B uilt-in DSC meets ITU Class D requirement
❍ Rugged waterproof construction
❍ E asy to salt crystallization.
Icom, Icom Inc. SAVE THIS INSTRUCTION MANUAL -
EXPLICIT DEFINITIONS
WORD RWARNING...
Instruction Manual - Page 12
...desired function can be assigned in the channel name, position, MMSI code entry mode, and so on. (pp. 7, 13, 22)
r UP AND DOWN/CHANNEL SELECT KEYS [∫•CH]/[&#...settings, and so on . ous screen.
y MENU KEY [MENU] (p. 68) Push to set the entered data, selected item, and so on . (pp. 12, 68) ➥➥ Push to check Favorite channels, change the scanning direction or manually...
Instruction Manual - Page 15
... displayed. ➥➥ "LOCAL" is displayed when the offset time is set. ➥➥ "MNL" is displayed when the time is manually entered. ➥➥ "UTC" is displayed when the GGA, GLL,...in GPS receiver. The last position is manually entered. may blink every 2 sec- The manually entered time is held for the IC-M323 and IC-M324: These models do not come with a built-in ...
Instruction Manual - Page 16
... Favorite channels. (p. 12) ➥➥ Push either key to change scanning direction or manually resumes a scan. (p. 17)
e TRANSMIT POWER KEY [HI/LO] ➥➥ Push to toggle the power high or low. (p. 12) • Some channels are set to only low power. ➥➥ While holding down [HI/LO], turn ON the...
Instruction Manual - Page 27
... direction or
10
manually resume the scan.
11
• A beep tone sounds and "16" blinks when a signal is displayed on the display. First, set the displayed channel ... is detected, the scan pauses until a long beep changes to 2 short beeps) to clear all Favorite channel settings in the Menu screen. (p. 70)
3
qqSelect the desired channel group. (p. 10)
4
wwSet the Favorite channels...
Instruction Manual - Page 32
... longitude position using Dial, and [Y]/[Z Select a desired number using Dial, or [Y]/[Z Push [ENT] or Dial to set it. • T o move the cursor, select either arrow, "←" or "→," then push [ENT...or later) format is connected. *For only IC-M323G and IC-M324G.
• Manual entry is disabled when a GPS receiver is on the 'W' or 'E' position.
22
• Push [EXIT] to return to...
Instruction Manual - Page 35
...8226; Push then push [PAUSE] to pause the 'Call repeat' mode, push [RESUME] to set it . Edit your latitude and longitude posi-
9
tion and UTC time. • Select a desired... not receiving valid position data, and both posi-
2
tion and time have been manually entered, the screen as follows: *For only IC-M323G and IC-M324G.
4
5
6
7
8
➥➥Push [CHG], then edit your ...
Instruction Manual - Page 42
... • Intership channels are '0' for the group you to make a DSC signal to set it. • T o move the cursor, select either arrow, "←" or "→...and the second digit is selected, enter the 8 digit ID code for any Coast station ID.
32 About Manual Entry: Enter a desired group ID in the following way:... "Manual Input," using Dial, or Push [ENT] or Dial to only a specific group.
Instruction Manual - Page 45
... confirmation screen is specified as '0' for the individual you want to set it.
3
• T o move the cursor, select either arrow, "←" or "→," then push
4
[ENT] or Dial.
• T he ID code for the Position Request Call can be entered first. (p. 20) • W hen "Manual Input" is selected, enter a desired 9 digit MMSI ID...
Instruction Manual - Page 47
...error... The ID code for the individual you want to announce your own position to a specific ship and ...set it.
3
• T o move the cursor, select either arrow, "←" or "→," then push
4
[ENT] or Dial.
• T he first digit is displayed. • Confirm the call can be entered first. (p. 20) • W hen "Manual Input" is selected, enter a desired 9 digit MMSI ID code...
Instruction Manual - Page 48
... position data, and both position and time have been manually entered, the screen as follows: *For only IC-M323G and IC-M324G.
Edit your latitude and longitude position and UTC ...time. • Select a desired number using Dial, or [Y]/[Z Push [ENT] or Dial to set it. • T o...
Instruction Manual - Page 49
... Push [BACK] to return to set it.
• T o move... hen "Manual Input" is selected, enter a desired 9 digit MMSI ID code for any...error beep sounds after pushing [FINISH].
6
• The first two digits are '0' for the individual you want to know a specific vessel is in the following way:
2
• Select a desired number using Dial or [Y]/[Z], then push Dial or [ENT]. • The ID code...
Instruction Manual - Page 57
...and longitude position and UTC time. • Select a desired number using Dial, or [Y]/[Z Push [ENT] or Dial to set it. • T o move the cursor, select either arrow, "←" or "→," then push [ENT] or...valid position data, and both position and time have been manually entered, the screen as follows: *For only IC-M323G and IC-M324G.
➥➥Push [CHG], then edit your ...
Instruction Manual - Page 72
...)
(default)
(default) eePush [EXIT] to return to "Auto TX" or "Manual TX." 7 DSC OPERATION
■■DSC Settings
D Position Entry (See page 22) D Add Individual ID/Group ID (See pages 19, 20) D Delete Individual ID/Group ID (See page 21)
DDAutomatic Acknowledgement
These items set to "Auto TX," the transceiver automatically transmits the Acknowledgment call...
Instruction Manual - Page 87
...;Cleaning
14
15
If the transceiver becomes dusty or dirty, wipe it , and replace the damaged fuse with a soft, dry cloth.
16
DO NOT use harsh ...blows or the transceiver stops functioning, track down the source of the problem, repair it clean with a new one of the proper rating.
Ask your...
2
tem is installed in the supplied DC power cable.
Knob bolts
Flat washers (M5)
4
■...
Icom IC-M424G Reviews
We have not received any reviews for Icom yet.