Hunter 82040 Support and Manuals
Get Help and Manuals for this Hunter item
This item is in your list!
View All Support Options Below
Free Hunter 82040 manuals!
Problems with Hunter 82040?
Ask a Question
Free Hunter 82040 manuals!
Problems with Hunter 82040?
Ask a Question
Popular Hunter 82040 Manual Pages
Owner's Manual - Page 1
Installation
Guide
ENGLISH
See page 2
Español
Vea la página 19
Energy Star Bath Fan Light Models 82040, 82041, 82042
READ and SAVE THESE INSTRUCTIONS
1
42936-01 10/17/2007
Owner's Manual - Page 2
...INSTRUCTIONS.
2) Before installing, servicing, or cleaning the unit, disconnect the power by turning off position, securely attach a prominent warning device, such as a tag, to the service... is not to scale
Bath Fan
3 ft. Use this... tub or shower installation, and must be installed within a minimum of...FOLLOWING: 1) Read all instructions before attempting to install or use not recommended by...
Owner's Manual - Page 3
..., do not use this fan with all applicable codes and standards, including fire-rated construction codes and standards.
8) When cutting or drilling into wall(s) or ceiling, do not block air intakes or exhaust in any manner.
3
42936-01 10/17/2007 off power unit.
13) Read specification label on product for installation in ceilings up to...
Owner's Manual - Page 4
...
M
97118-02-000 97118-03-000
97118-04-000
x2 N 74508-03-133
O 97932-01-262 P 87259-01-000
Housing Light Fixture Thumbnuts
Wiring Cover Wiring Cover Screw Strain Relief Bracket Strain Relief Bracket Screw Fan Assembly
Fan Mounting Screws Light Fixture
Lens
Included.
If damaged, call 1-888-830-1326 for replacement. Check all the parts.
Owner's Manual - Page 5
Choose Installation Option For New Construction - Remove the wiring cover. suspended between, joists go to step B1, page 7. For Existing Construction - attaching to joist, go to step A1, page 5. accessible from above, go to step C1, page 9. E
Loosen the wiring cover screw. C
D
Remove the fan assembly from below, go to step D1, page...
Owner's Manual - Page 6
... relief.
Drive mounting screws (supplied) into the wiring access hole you made earlier. Tighten the strain relief around the wire.
42936-01 10/17/2007
6
Install the wiring and the strain relief into joist or framing.
attaching to joist
A1
OR
Pop out a wiring access slug. Section A - A4
A5
3"
Run the...
Owner's Manual - Page 9
...fan and check to make sure the opening needs to be 11" x 9 5/8".
9
42936-01 10/17/2007
If ducting does not fit securely, an adapter
may need to be purchased. The opening is large enough to secure joints. Connect 4" duct and vent to Section E Final Installation... on page 14. Go to the outside.
B10
B11
Install the wiring and the strain ...
Owner's Manual - Page 11
..., leaving 3" between the screw head and the joist. (Screws are supplied.)
Attach the rails onto the screws. Tighten the strain relief around the wire. C12
Install the wiring and the strain relief into the wiring access hole you made earlier.
If ducting does not fit securely, an adapter
may need to...
Owner's Manual - Page 12
...of the wiring access slugs on page 14. D3 EXISTING FAN
D4
3"
Remove an existing fan and check to make sure the opening is no existing fan choose an appropriate
location to make an 11" x 9 ...Tighten
the strain relief around the wire. If there is large enough to Section E Final Installation on the top of the wire and the strain relief.
Section D - Existing Construction - Remove the ...
Owner's Manual - Page 13
Screw mounting screws into the ceiling. Use duct tape to Section E Final Installation on page 14. Go to secure joints. If ducting does not fit securely, an adapter
may need to the ...-01 10/17/2007 D9
5/8
5/8
1/2
1/2
Position the bottom edge of the housing flush with the sheetrock.
D5
D6
Install the wiring and the strain relief into the wiring access hole you made earlier.
Owner's Manual - Page 14
... by inserting the tabs as shown.
DO NOT ALLOW THE FAN TO HANG FROM THE WIRING HARNESS. E2
? INSTALLATION IS
EASIER IF TWO PEOPLE ARE INVOLVED. Section E - Final Installation
E1
Fan Motor Night Light
Light
2 Pin
Black White
3 Pin
White Red Night Light Black Light
*Option
*Option Fan & Main Light Together
Ground Green
A
Bare Copper Black Main Switch 1 (AC In...
Owner's Manual - Page 15
E10
Install the strain relief bracket. E5
E6
Secure the fan assembly by tightening the two fan mounting screws. Remove light bulb cover. DO NOT ALLOW THE LIGHT FIXTURE TO HANG FROM THE WIRING HARNESS.
INSTALLATION IS EASIER IF TWO PEOPLE ARE INVOLVED.
15
Position lighting fixture over mounting posts.
42936-01 10/17/2007
E7
E8
Remove thumbnuts. E9
Plug in wiring harness.
Owner's Manual - Page 16
E11
E12
Secure the fan assembly by tightening the two fan mounting thumbnuts. Install light bulb cover. Restore power at the source.
42936-01 10/17/2007
16
E13
E14
Install night light.
E9
Complete.
Owner's Manual - Page 17
..., contact Hunter Technical Support (see Troubleshooting section) to make sure it matches the wiring diagram. TO CLEAN THE FAN ASSEMBLY: Disconnect power to clean the bezel.
Trouble Shooting
Problem: Fan does not come on . Solution: • Replace the light bulb with a new bulb. • Turn power on , replace fuse, or reset breaker. • Hunter Fan Bath Ventilators are...
Owner's Manual - Page 18
...EXPRESS WARRANTY SET FORTH ABOVE FOR SUCH MOTORS OR OTHER PARTS.
If your Bath Fan or provide a replacement free of charge.
To obtain servicing, contact Hunter Fan Company Technical Support at http://www. Proof of charge at our Service Department in material or workmanship, we will repair or, at our option, either refund the actual purchase price of your Hunter Bath Fan motor...
Hunter 82040 Reviews
Do you have an experience with the Hunter 82040 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Hunter yet.
Earn 750 points for your review!