Hunter 23685 Support and Manuals
Get Help and Manuals for this Hunter item
View All Support Options Below
Free Hunter 23685 manuals!
Problems with Hunter 23685?
Ask a Question
Free Hunter 23685 manuals!
Problems with Hunter 23685?
Ask a Question
Popular Hunter 23685 Manual Pages
Installation Guide - Page 1
...-01 • 02/20/04 For instructions to install your ceiling fan, go to your ceiling fan site. o e outlet box is positioned to allow you cannot lock the circuit breakers in contact with 2 • Installing the Ceiling Plate. o Six inches of the fan and light kit. You will hold full weight of the ceiling. Attach a 2" x 4" support brace between two joists. Position it...
Owner's Manual - Page 1
For Your Records and Warranty Assistance Model Name Catalog/Model No Serial No Date Purchased Where Purchased For reference also attach your receipt or a copy of your receipt to the manual.
41923-01 • 11/21/05
Owner's Manual - Page 2
... Hunter replacement parts. • To reduce the risk of personal injury, attach the fan directly to the
support structure of the building according to these instructions, and use a solid-state speed control with national and local electrical codes and ANSI/NFPA 70. If you cannot lock the circuit breakers in accordance with this entire manual carefully before installing your fan...
Owner's Manual - Page 3
...;e steps in one of your Hunter fan in this manual include instructions for all three Installer's Choice mounting methods. All Hunter fans use sturdy 3/4" diameter pipe to the ceiling, recommended for ceilings less than 8 feet high
For ceilings higher than 8 feet, you maximum installation flexibility and ease.
You can purchase Hunter extension downrods. To install and use the accessories...
Owner's Manual - Page 4
...dependent upon installation site)
Checking Your Fan Parts
Carefully unpack your Hunter dealer or call Hunter Technical Support Department at 888-830-1326. To install a ceiling fan, be sure you can direct you begin installing the fan, follow all the instructions in sets,
as they were shipped. Proper ceiling fan location and attachment to the included Parts Guide. Preparing the Fan Site
Before...
Owner's Manual - Page 5
... through the hole in diameter.
2-2. Hunter Fan Company Drill two pilot holes into the 9/64" pilot holes; Align the slotted holes in the wood support structure.
2 • Installing the Ceiling Plate
2-1. Position the isolators between the ceiling plate and ceiling by inserting the raised areas on the ceiling plate are pointing towards the ceiling peak. do not use slotted...
Owner's Manual - Page 6
...
Low Profile Washer
You can assemble your fan for standard mounting (steps 3-1 - 3-2) or for low profile mounting (steps 3-3 - 3-5). Assemble securely with the holes in these installation instructions. Once assembled, do not remove the downrod.
3-3. Using the provided allen wrench, loosen the allen head set screw on the ceiling plate through the canopy and canopy trim...
Owner's Manual - Page 7
...Hunter Fan Company Do not use any interference received, including interference that they don't match, the controller will not function. For instructions on -off 1 = on
7
CAUTION: e remote control device complies with part 15 of the FCC rules.
maximum lamp is 1 Amp;
Example Jumpers Settings...jumpers are located near each fan set to a different code, so that incorporates an...
Owner's Manual - Page 8
... black power wire from the ceiling to the black wire from the receiver (marked on red tag "LIVE IN")
5-5. Push all these connections use a qualified electrician.
5-1.
Hunter Fan Company
41923-01 • 11..."LIGHT OUT")
Small Wire Nut
• e black wire from the fan to the black wire from the receiver (marked on white tag "FAN OUT")
• e white wire from the fan...
Owner's Manual - Page 9
...-01 • 11/21/05
Canopy Screw
Hunter Fan Company Holding the canopy, raise the fan off the hook.
6-2.
Using both hands, ...push the canopy trim ring up to remove the canopy
trim ring, follow these steps:
1. 6 • Installing the Canopy and Canopy Trim Ring
6-1. Rotate the canopy clockwise until the tabs on the ceiling...
Owner's Manual - Page 10
... screws are installed in the motor to the fan. If you used grommets, the blades may include blade grommets.
Steps 7-1 - 7-2
Use without grommet Blade Mounting Screw
Hunter Fan Company
Step 7-4
41923-01 • 11/21/05 Attach each blade, insert one blade mounting screw through the
Blade Assembly Screws
blade iron, and attach lightly to...
Owner's Manual - Page 11
... screws are firmly situated in the narrow end of the housing.
8-3. Install the remaining housing assembly screw into the switch housing mounting plate.
8-2. Failure... the upper switch housing with a number of accessory light kits. Lower Switch Housing
Housing Assembly Screw
Steps 8-5 - 8-6
41923-01 • 11/21/05
Hunter Fan Company Housing Assembly Screw
Upper Switch Housing
11
Note...
Owner's Manual - Page 13
... the opposite position. Occasionally, apply a light coat of furniture polish for added protection and beauty. Clean painted and high-gloss blades in warm weather to prevent scratching. A vacuum cleaner brush nozzle can remove heavier dust. Clean wood finish blades with a direct breeze. Restart fan. Ceiling fans work best by blowing air downward (counterclockwise blade...
Owner's Manual - Page 14
...section. 3.
If the transmitter LED light does not come on , replace fuse, or reset breaker. 2. Refer to balance the fan. 2. Remove the shipping bumpers 6. If your fan wobbles when operating, use the enclosed balancing kit and instructions to 4• Setting the Remote Transmitter and Receiver 7 for more information. Turn power off, support fan very carefully, and check that...
Parts Guide - Page 1
... Assembly
Blade Iron Set
Blade Set
Screw, Blade Iron Armature
Hardware Kit
Rubber Blade Grommet
Blade Assembly Screw
Screw, Machine, #6-32
Wire Connector
Balancing Kit
Switch Housing Assembly Screw
Allen Wrench
Remote Control Transmitter
Remote Control Cradle
Remote Control Receiver
Model # Asm. REFER TO THE INSTALLATION MANUAL FOR FULL ASSEMBLY INSTRUCTIONS. Hardware (Drawn to...
Hunter 23685 Reviews
We have not received any reviews for Hunter yet.