Hunter 82032 Support and Manuals
Get Help and Manuals for this Hunter item
View All Support Options Below
Free Hunter 82032 manuals!
Problems with Hunter 82032?
Ask a Question
Free Hunter 82032 manuals!
Problems with Hunter 82032?
Ask a Question
Most Recent Hunter 82032 Questions
Change Motor To Higher Motor
Can i cahnge the motor from 70 cfm to 110 cfm in the hunter bathroom fan? IS it the same size?
Can i cahnge the motor from 70 cfm to 110 cfm in the hunter bathroom fan? IS it the same size?
(Posted by tywhit007 10 years ago)
Popular Hunter 82032 Manual Pages
Owner's Manual - Page 1
Installation
Guide
ENGLISH
See page 2
Español
Vea la página 19
Energy Star Bath Fan Models 82030, 82031, & 82032
READ and SAVE THESE INSTRUCTIONS
42935-01 06/04/2007
Owner's Manual - Page 2
..., or injury to persons. NOTE: This illustration is not suitable for Heating, Refrigeration and Air-Conditioning Engineers (ASHRAE), and the local code authorities. Do not use this manual. SAVE THESE INSTRUCTIONS.
2) Before installing, servicing, or cleaning the unit, disconnect the power by turning off position, securely attach a prominent warning device, such as described in this...
Owner's Manual - Page 3
... dust, etc. off power unit.
13) Read specification label on product for further information and requirements.
14...fan with all applicable codes and standards, including fire-rated construction codes and standards.
8) When cutting or drilling into wall(s) or ceiling, do not block air intakes or exhaust in a wall. Do not install this appliance in a tub or shower enclosure.
7) Installation...
Owner's Manual - Page 4
...replacement. x3 A
F 95044-01-000 Mounting Rails
G 97128-01-000 H 97517-01-000
Housing
*B *C
3/8" Cable Connector
x2 D
Attachment Screws
x4 E
Mounting Screws
* NOTE: Strain relief (not supplied) cable connector must be installed... Bracket Strain Relief Bracket Screw Fan Assembly
Fan Mounting Screws Bezel
Included. Check all the parts. Before Installation
A
Tools Needed. (Not supplied...
Owner's Manual - Page 5
attaching to joist, go to step B1, page 7. accessible only from the housing. Choose Installation Option For New Construction - For New Construction - C
D
Remove the fan assembly from below, go to step D1, page 12.
42935-01 06/04/2007 E
Loosen the wiring cover screw.
For Existing Construction - suspended between, joists ...
Owner's Manual - Page 6
Tighten the strain relief around the wire.
42935-01 06/04/2007
Install the wiring and the strain relief into joist or framing.
Section A - A4
A5
3"
Run the power supply wire through the strain relief, leaving 3" between the ...
Owner's Manual - Page 7
... the bottom edge of the joist based upon the the thickness of the rails.
A6
Go to secure joints. Use duct tape to Section E Final Installation on page 14.
Section B - suspended between joists
B1
OR
Pop out a wiring access slug. Note the orientation of of the outer ends of your sheetrock...
Owner's Manual - Page 9
... large enough to be purchased. B10
B11
Install the wiring and the strain relief into the wiring access hole you made earlier. Connect 4" duct and vent to secure joints.
accessible from above
C1
NO EXISTING FAN
11"
9 �⁄�"
OR
Remove an existing fan and check to make sure the opening needs...
Owner's Manual - Page 11
... the joist. (Screws are supplied.)
Attach the rails onto the screws.
If ducting does not fit securely, an adapter
may need to the outside. C12
Install the wiring and the strain relief into the wiring access hole you made earlier. C9
C10
3"
Tighten screws. Connect 4" duct and vent to be purchased...
Owner's Manual - Page 12
Go to Section E Final Installation on the top of the wire and the strain relief. If there is large enough to make sure the opening .
42935-01 06/04/... the wire.
Remove the mounting rail brackets. accessible from below
D1
D2
Remove one of the wiring access slugs on page 14. D3 EXISTING FAN
D4
3"
Remove an existing fan and check to make an 11" x 9 5/8" opening is no existing...
Owner's Manual - Page 13
... tape to the outside.
D7
Connect 4" duct and vent to secure joints.
If ducting does not fit securely, an adapter
may need to Section E Final Installation on page 14. Screw mounting screws into the wiring access hole you made earlier.
Go to be purchased. D5
D6...
Owner's Manual - Page 14
... not pinched between joists. E3
E4
Connect fan wiring harness.
bly and the housing. Make sure all wiring connections are inside the wiring cover box. E5
Install the fan assembly by tightening the two fan mounting screws.
42935-01 06/04/2007
14
Install the strain relief bracket. Install the wiring cover box.
DO NOT ALLOW...
Owner's Manual - Page 15
Restore power at the source.
15
42935-01 06/04/2007 E9
Complete.
E7
E8
Install the bezel by inserting the wire clips into the tabs on the inside of the housing.
Owner's Manual - Page 16
..., a mild detergent such as listed below. Remove the fan from the housing and unplug the fan wiring harness. When the fan is noisy. Reinstall the bezel.
Trouble Shooting
Problem: Fan does not come on , replace fuse, or reset breaker. • Hunter Fan Bath Ventilators are extremely quiet. To confirm that the fan is running, place your hand near the vents to...
Owner's Manual - Page 17
... option, replace the defective part free of sale to you due to a defect in Memphis, Tennessee.
This warranty is voided if your Bath Fan or provide a replacement free of the bath exhaust fan. This warranty excludes and does not cover defects, malfunctions or failures of any Hunter Bath Fan which were caused by repairs by persons not authorized by us, mishandling, improper installation...
Hunter 82032 Reviews
We have not received any reviews for Hunter yet.