Hunter 82032 Support Question
Hunter 82032 Support Question
Find answers below for this question about Hunter 82032.Need a Hunter 82032 manual? We have 1 online manual for this item!
Question posted by tywhit007 on July 30th, 2013
Change Motor To Higher Motor
Can i cahnge the motor from 70 cfm to 110 cfm in the hunter bathroom fan? IS it the same size?
Current Answers
Related Hunter 82032 Manual Pages
Owner's Manual - Page 1
Installation
Guide
ENGLISH
See page 2
Español
Vea la página 19
Energy Star Bath Fan Models 82030, 82031, & 82032
READ and SAVE THESE INSTRUCTIONS
42935-01 06/04/2007
Owner's Manual - Page 2
... manufacturer's guideline and safety standards, such as a tag, to the service panel.
3) This unit must not be grounded.
4) This appliance is not to scale
Bath Fan
3 ft. W arning
TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY, OBSERVE THE FOLLOWING: 1) Read all instructions before attempting to install or use only.
min...
Owner's Manual - Page 3
...)-protected branch circuit.
42935-01 06/04/2007 Ductwork must point upward.
10) Ducted fans must be done by or near children or invalids and whenever the is to be installed over...hidden utilities.
9) Do not install this unit is left operating and unattended.
12) To avoid motor bearing damage and noisy/unbalanced blower wheel, keep drywall spray, construction dust, etc. Do not ...
Owner's Manual - Page 4
...97934-01-262
Wiring Cover Wiring Cover Screw Strain Relief Bracket Strain Relief Bracket Screw Fan Assembly
Fan Mounting Screws Bezel
Included. If damaged, call 1-888-830-1326 for replacement. Before...assembly time: 30 to 60 minutes
B
Turn off the power source.
42935-01 06/04/2007
Loosen the fan mounting screws.
x3 A
F 95044-01-000 Mounting Rails
G 97128-01-000 H 97517-01-000
Housing...
Owner's Manual - Page 5
... the wiring cover screw. For New Construction -
For Existing Construction - attaching to joist, go to step A1, page 5. accessible only from the housing. C
D
Remove the fan assembly from below, go to step D1, page 12.
42935-01 06/04/2007
Owner's Manual - Page 9
Use duct tape to accommodate the new fan
housing. accessible from above
C1
NO EXISTING FAN
11"
9 �⁄�"
OR
Remove an existing fan and check to make sure the opening needs to be 11" x 9 5/8".
42935-01 06/04/2007 Go to the outside. Connect 4" duct and vent to ...
Owner's Manual - Page 12
... from below
D1
D2
Remove one of the wiring access slugs on page 14. Existing Construction - D3 EXISTING FAN
D4
3"
Remove an existing fan and check to make an 11" x 9 5/8" opening is no existing fan choose an appropriate
location to make sure the opening .
42935-01 06/04/2007
12
Run the power...
Owner's Manual - Page 14
...A
Bare Copper
A
Black
A
White
Connect the wiring as shown and pushing the fan assembly into the housing. Make sure all wiring connections are inside the wiring cover ...not pinched between joists.
bly and the housing.
E3
E4
Connect fan wiring harness. Section E -
E5
Install the fan assembly by tightening the two fan mounting screws.
42935-01 06/04/2007
14
Install the strain ...
Owner's Manual - Page 16
... switch off the breaker or removing the fuse. Remove the fan from the housing and unplug the fan wiring harness.
Maintenance
The fan motor is clean, plug in the fan wiring harness. Trouble Shooting
Problem: Fan does not come on , replace fuse, or reset breaker. • Hunter Fan Bath Ventilators are extremely quiet. TO CLEAN THE BEZEL: Carefully...
Owner's Manual - Page 17
... TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IN RESPECT TO ANY HUNTER FAN BATH FAN MOTOR OR OTHER FAN PART, IS EXPRESSLY LIMITED TO THE PERIOD OF THE EXPRESS WARRANTY SET FORTH ABOVE FOR SUCH MOTORS OR OTHER PARTS. This warranty excludes and does not cover defects, malfunctions or failures of any...
Similar Questions
Hunter 90064 Fan Motor
How can I get a replacement part for the fan motor
How can I get a replacement part for the fan motor
(Posted by marselagsu 1 year ago)
Anywhere To Get A New Fan Motor For Hunter Avantine 83003 Bathroom Exhaust Fan?
(Posted by Ssmith4005 2 years ago)
Replacement Fan Motor
where can I get a replacement fan motor for model 90052/53/54/58
where can I get a replacement fan motor for model 90052/53/54/58
(Posted by joeflanagan60 7 years ago)
Fan Blade Screws To Motor
I have a 23856 Hunter Original that I have lost the screws that attach the blades to the motor. Out ...
I have a 23856 Hunter Original that I have lost the screws that attach the blades to the motor. Out ...
(Posted by TDaniels22953 11 years ago)
Motor Replacement For Hunter Fan 23781
How can I get a replacement motor for hunter fan 23781? Hunter has not responded to my email, I am o...
How can I get a replacement motor for hunter fan 23781? Hunter has not responded to my email, I am o...
(Posted by Bernicekaufman 11 years ago)