HP xw Workstation series Setup and Troubleshooting Guide
Page 44
...will help you diagnose the problem. If the system beeps, then your workstation, monitor, or software, the following provides a list...error codes that the monitor is turned on and the green monitor light is on. ● Turn up the brightness and contrast controls of this document for instructions. ● Be sure that all cables for information on interpreting diagnostic lights and audible codes. ● Press and hold any key on your workstation...loose or incorrect connections. ● Wake the workstation by visiting http://www.hp.com/go / workstationsupport. if the monitor is...
...will help you diagnose the problem. If the system beeps, then your workstation, monitor, or software, the following provides a list...error codes that the monitor is turned on and the green monitor light is on. ● Turn up the brightness and contrast controls of this document for instructions. ● Be sure that all cables for information on interpreting diagnostic lights and audible codes. ● Press and hold any key on your workstation...loose or incorrect connections. ● Wake the workstation by visiting http://www.hp.com/go / workstationsupport. if the monitor is...
HP xw Workstation series Setup and Troubleshooting Guide
Page 48
...the configuration, you still cannot resolve the issue, contact Customer Support. Observe the beeps and LED lights on the Documentation and Diagnostics CD (http://www.hp.com/support/ workstation_manuals). Table 5-2 Hardware installation problems Problem Probable Cause Recommended Solution ...beep) codes This section describes the front panel light (LED) error and operation codes as well as part of changes to determine possible causes. Ensure that the device is not seated or connected properly. For more information about using the correct memory modules and to the workstation...
...the configuration, you still cannot resolve the issue, contact Customer Support. Observe the beeps and LED lights on the Documentation and Diagnostics CD (http://www.hp.com/support/ workstation_manuals). Table 5-2 Hardware installation problems Problem Probable Cause Recommended Solution ...beep) codes This section describes the front panel light (LED) error and operation codes as well as part of changes to determine possible causes. Ensure that the device is not seated or connected properly. For more information about using the correct memory modules and to the workstation...
HP xw Workstation series Setup and Troubleshooting Guide
Page 50
...the failure. Five beeps. To prevent damage, disconnect the workstation power cord before you remove a component. 1. CAUTION: Internal components might be on the system board. Clear CMOS. Contact HP for assistance. Table 5-3 Diagnostic lights and audible codes (continued) Activity ... at a time to video). Pre-video memory error CAUTION: Internal components might be on the system board. Reseat DIMMs. 2. Contact HP for assistance. 44 Chapter 5 Troubleshooting ENWW To prevent damage, disconnect the workstation power cord before you remove a component. 1. ...
...the failure. Five beeps. To prevent damage, disconnect the workstation power cord before you remove a component. 1. CAUTION: Internal components might be on the system board. Clear CMOS. Contact HP for assistance. Table 5-3 Diagnostic lights and audible codes (continued) Activity ... at a time to video). Pre-video memory error CAUTION: Internal components might be on the system board. Reseat DIMMs. 2. Contact HP for assistance. 44 Chapter 5 Troubleshooting ENWW To prevent damage, disconnect the workstation power cord before you remove a component. 1. ...
HP xw4600 Workstation - Service and Technical Reference Guide
Page 119
... VGA adapter. During operation ● Look for information on Self Test (POST). ENWW HP troubleshooting resources and tools 109 If the system beeps, then your system by visiting http://www.hp.com/go / workstationsupport. The blinking lights are error codes that the workstation and monitor are disabled; If the system does not shut down the system...
... VGA adapter. During operation ● Look for information on Self Test (POST). ENWW HP troubleshooting resources and tools 109 If the system beeps, then your system by visiting http://www.hp.com/go / workstationsupport. The blinking lights are error codes that the workstation and monitor are disabled; If the system does not shut down the system...
HP xw4600 Workstation - Service and Technical Reference Guide
Page 122
... pause, and then 6 beeps Pre-video graphic card error. Locate a faulty device by removing all devices and then reinstalling one at a time until the workstation fails. Continue adding devices to...then a 2-second pause, and then 5 beeps Pre-video memory error. 1. Replace the device causing the failure. Verify the power supply functionality. For systems with HP memory. 4. Replace the graphic card. 3.... system board. For systems with graphic cards: 1. Table 6-1 Diagnostic LED codes (continued) Chassis indicator LEDs Power LED and sound activity Diagnosis and service action Blinks...
... pause, and then 6 beeps Pre-video graphic card error. Locate a faulty device by removing all devices and then reinstalling one at a time until the workstation fails. Continue adding devices to...then a 2-second pause, and then 5 beeps Pre-video memory error. 1. Replace the device causing the failure. Verify the power supply functionality. For systems with HP memory. 4. Replace the graphic card. 3.... system board. For systems with graphic cards: 1. Table 6-1 Diagnostic LED codes (continued) Chassis indicator LEDs Power LED and sound activity Diagnosis and service action Blinks...