HP LE1901w/LE1901wm and LE2201w LCD Monitors User Guide
Page 7
...full-screen support for lower resolutions; 1 Product Features HP LCD Monitors The LCD (liquid crystal display) monitors have an active matrix, thin-film transistor (TFT) panel. The monitor models and features include: ● LE1901w/LE1901wm models, 48.3 cm (19-inch) diagonal viewable area display with 1680 x 1050...to insert filters (purchased separately) to block side screen viewing (select models) ● Security slot provision on rear of monitor for optional cable lock ● Internal speakers (select models) ● Audio input signal cable (select models) ● On-Screen Display (...
...full-screen support for lower resolutions; 1 Product Features HP LCD Monitors The LCD (liquid crystal display) monitors have an active matrix, thin-film transistor (TFT) panel. The monitor models and features include: ● LE1901w/LE1901wm models, 48.3 cm (19-inch) diagonal viewable area display with 1680 x 1050...to insert filters (purchased separately) to block side screen viewing (select models) ● Security slot provision on rear of monitor for optional cable lock ● Internal speakers (select models) ● Audio input signal cable (select models) ● On-Screen Display (...
HP LE1901w/LE1901wm and LE2201w LCD Monitors User Guide
Page 11
...of color or disorientation of the LCD panel. CAUTION: Do not touch the surface of the liquid crystals. Be sure the base is turned off to the desired position. 3 Setting Up the Monitor To set up the monitor, ensure that the power is securely locked in place. Figure 3-1 Attaching the... both hands, position the pedestal over the base and press down firmly to lock it in place and adjust the tilt angle to the monitor, computer system, and other attached devices, then follow the instructions below. Attaching the Monitor Base 1. Pressure on a flat surface such as a table top. 2. ...
...of color or disorientation of the LCD panel. CAUTION: Do not touch the surface of the liquid crystals. Be sure the base is turned off to the desired position. 3 Setting Up the Monitor To set up the monitor, ensure that the power is securely locked in place. Figure 3-1 Attaching the... both hands, position the pedestal over the base and press down firmly to lock it in place and adjust the tilt angle to the monitor, computer system, and other attached devices, then follow the instructions below. Attaching the Monitor Base 1. Pressure on a flat surface such as a table top. 2. ...
HP LE1901w/LE1901wm and LE2201w LCD Monitors User Guide
Page 27
...Time ● Set On Time ● Timer: On/Off ● Sleep Now ENWW Identifying Monitor Conditions 21 If the OSD is locked, the warning message OSD Lockout displays for ten seconds. ◦ If the OSD is locked, press and hold the Menu button for 10 seconds to unlock the OSD. ◦ If... the OSD is not receiving a video signal from the PC on the monitor video input connector. Check to set higher than the monitor supports (models LE1901w/LE1901wm). ● Input Signal Out ...
...Time ● Set On Time ● Timer: On/Off ● Sleep Now ENWW Identifying Monitor Conditions 21 If the OSD is locked, the warning message OSD Lockout displays for ten seconds. ◦ If the OSD is locked, press and hold the Menu button for 10 seconds to unlock the OSD. ◦ If... the OSD is not receiving a video signal from the PC on the monitor video input connector. Check to set higher than the monitor supports (models LE1901w/LE1901wm). ● Input Signal Out ...
HP LE1901w/LE1901wm and LE2201w LCD Monitors User Guide
Page 28
... mode to On to 00:00. Note that the time is displayed as 13 hours 15 minutes. A power failure or loss of power to the monitor will need to reset the sleep timer mode. 5. Press the Menu button again to enter the time for Sleep Time or On Time. After setting... off immediately and stays in the time chosen. 10. Press the Menu button on the monitor front panel to lock in sleep mode until the next On Time activates or a monitor button is pressed. 22 Chapter 4 Operating the Monitor ENWW If this occurs, you reset the time for minutes. 8. Scroll down and highlight and...
... mode to On to 00:00. Note that the time is displayed as 13 hours 15 minutes. A power failure or loss of power to the monitor will need to reset the sleep timer mode. 5. Press the Menu button again to enter the time for Sleep Time or On Time. After setting... off immediately and stays in the time chosen. 10. Press the Menu button on the monitor front panel to lock in sleep mode until the next On Time activates or a monitor button is pressed. 22 Chapter 4 Operating the Monitor ENWW If this occurs, you reset the time for minutes. 8. Scroll down and highlight and...