Hannspree ST259MUB Support and Manuals
Get Help and Manuals for this Hannspree item
View All Support Options Below
Free Hannspree ST259MUB manuals!
Problems with Hannspree ST259MUB?
Ask a Question
Free Hannspree ST259MUB manuals!
Problems with Hannspree ST259MUB?
Ask a Question
Popular Hannspree ST259MUB Manual Pages
User Manual - Page 3
... Information 42 6.2.3 Power-out Protection Capability 42 6.3 Component Program Codes 43 7. Adjusting On-Screen Display (OSD) Settings 28
3.1 OSD Setting Menus 29 3.2 Adjusting Picture Settings 29 3.3 Adjusting Audio Settings 30 3.4 Adjusting Channel Settings 31 3.5 Adjusting V-CHIP Settings 32 3.6 Adjusting Setup Settings 33 4. Troubleshooting 34 5. Setting the TV on the Wall 50 8.
User Manual - Page 6
... for use a VGA monitor cable with liquids, such as vases, shall be placed on the source signal, use by qualified service personnel only. Notes:
• The LCD TV is for the emission of heat. CAUTION
These servicing instructions are excluded.
• This device uses a VGA connector to connect to a PC. English
Safety Notices
Installation Safety Notes Location...
User Manual - Page 7
... outlet. If the provided plug does not fit into your safety. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from tip-over.
6 Clean only with manufacturer's instructions.
8. A polarized plug has two blades with one wider than the other apparatus (including...
User Manual - Page 9
... the TV is otherwise damaged, unplug the power cord immediately and contact an authorized service technician.
5. If the TV is ...TV's vents, do not place the TV on the power cord. The screen of the TV.
4. Avoid hitting or scraping it. Hold the plug.
Install the outdoor antenna away from power transmission lines to use the TV unattended. 8. Installation
1. Do not place the TV...
User Manual - Page 13
...
1 Getting Started
1.1 Package Contents Make sure the following components are included in the box. Please contact Hannspree Customer Service immediately if anything is missing or damaged. • TV • Power cord • Remote control and batteries • User's manual • Quick start guide • Warranty card • Attention notice card • Cleaning cloth • HDMI cable...
User Manual - Page 14
... Pull down
Note: The supporting devices mentioned in TV tuner • Audio/ Video support:
- Convenient control buttons located on the TV and a handy remote control let you connect to the standard CVBS, S-Video, component, and HDMI input ports (location of these ports depends on model). USB - You can watch NTSC/ATSC broadcast, cable, or digital television channels, and easily connect...
User Manual - Page 16
....
VGA (PC) input
Connect to an antenna or cable TV. Earphone output Cable/ Antenna
EAR PHONE
VHF / UHF
CABLE / ANTENNA
Connect to the included power cord. Composite inputs
AV
AUDIO
R
L
VIDEO
Connect to an external device, such as a DVD player, set-top box, or a PC's DVI/ HDMI port. USB
USB
Support JPEG and MP3 files.
15 English
1.4 Input and...
User Manual - Page 21
... to an antenna or cable TV line, try scanning for channels.
20 English
2 Setting up your TV
2.1 Basic Connections 2.1.1 Power Connection 1 Connect the power cord to the AC IN input jack on the rear of the TV. 2 Insert the plug at the other end of the power cord into a power outlet. 2.1.2 Connecting an Antenna or Cable TV Connect one end of...
User Manual - Page 35
... not available.
Replace the battery with high quality signals.
Make sure the battery is clear.
Adjust the saturation in the OSD Setup menu. Adjust the sharpness setting. Adjust the direction of interference. Turn the mute off.
Make sure the video signal cable is in the OSD Channel menu. Make sure the TV power cord is plugged in...
User Manual - Page 39
... the next/previous electronic equipment POWER signal without saving the new electronic equipment code; For example, inputting "02" then pressing RETURN does affect the "02" already input.
6.1.3 Searching Codes
If the desired electronic equipment code for 2 seconds, prompting user to use the code-searching function with operating procedures as follows:
38 If setting is successful, the...
User Manual - Page 40
... have volume locked up ). The indicator light then goes off ; During the setting process, releasing the electronic equipment button exits the setting mode immediately without changing the status prior to transmit code values under TV mode and you wish to transmit code values under other than VOL+/VOL- twice consecutively to cancel channel lock under...
User Manual - Page 41
... it goes off and setting mode is TV upon first power-on again, showing setting mode has been entered.
2. While holding the electronic equipment button, first press < (left arrow), then press OK. During the setting process, releasing the electronic equipment button exits the setting mode immediately without changing the status prior to setting.
5. Transmit TV code
AUDIO
--
after...
User Manual - Page 42
... Unlocked
Note:
Each re-powering restores factory setting, and all electronic equipment modes transmit TV-mode infrared (IR) signal until being set up through code setting. For example, setting the electronic equipment code of CABLE as '0001' stops transmitting TV code, whereas AUDIO and DVD continue to transmit TV code.
41 Default volume lock setting:
Electronic equipment
VOL+, VOL...
User Manual - Page 43
... Except TV equipment, all the buttons on remote controls corresponding to other electronic equipments (AUDIO, CABLE, and DVD) are not necessarily functional, but most of those remote controls only include power control, channel control, volume control, etc.
6.2.3 Power-out Protection Capability During battery replacement, all settings are disabled under TV mode but a fixed code for the TV...
User Manual - Page 51
... read the instructions of the stand base.
*Installing the LCD TV requires special skill that results in accident or injury. Hannspree bears no responsibility for improper mounting or mounting that should not attempt to do the work themselves.
English
SERVICE
VHF / UHF
7 Setting the TV on the Wall
Dissembling the stand base: 1 Disconnect all the cables and cords from the TV to prevent...
Hannspree ST259MUB Reviews
We have not received any reviews for Hannspree yet.