Gigabyte GA-7PESVL Support and Manuals
Get Help and Manuals for this Gigabyte item
View All Support Options Below
Free Gigabyte GA-7PESVL manuals!
Problems with Gigabyte GA-7PESVL?
Ask a Question
Free Gigabyte GA-7PESVL manuals!
Problems with Gigabyte GA-7PESVL?
Ask a Question
Popular Gigabyte GA-7PESVL Manual Pages
Manual - Page 1
GA-7PESVL
Dual LGA2011 sockets motherboard for Intel® E5-2600 series processors
User's Manual
Rev. 1001
Manual - Page 6
GA-7PESVL Motherboard Layout
34
44 1 2 3 4
5
33
35 36 37
32
38 39
31
30 29
41 42 43 45 40
47 46 48
49
57
6
54 55 56 53 52
7 50 51
8
21 22
17 15 18 16
9 10
28
23
24
27
25
26
20 19
14 13
11 12
- 6 -
Manual - Page 32
Hardware Installation
- 32 - 1) BIOS_RVCR1 (BIOS Recovery Jumper)
BIOS_RVCR1 1 1-2 Close: Normal operation. (Default setting) 1 2-3 Close: BIOS recovery mode.
8) PASSWORD1 (Clearing Supervisor Password Jumper)
PASSWORD1 1 1-2 Close: Normal operation. (Default setting) 1 2-3 Close: Skip supervisor password.
Manual - Page 33
Hardware Installation
Failure to do so may cause damage to the motherboard.
• After system restart, go to BIOS Setup Exit menu and load factory defaults (select Restore Defaults) or manually configure the BIOS settings (refer to touch the two pins for BIOS configurations).
- 33 - To clear the CMOS values, place a jumper cap on your...
Manual - Page 36
...
1
1 P5V
2 SATA_DOM_1
3 GND
11) BIOS_WP1 (BIOS Write Protect Jumper)
1-2 Close: Normal operation. (Default setting) 1
2-3 Close: Enable BIOS write protect function. 1
Hardware Installation
- 36 -
Please refer to the pin definition table in order to 2-3 pins (Default setting), in the following. Definition
1
1 P5V
2 SATA_DOM_0
3 GND
For SATA_DOM_1
Pin No. 9/10) SATA_DOM_0...
Manual - Page 55
... SATA mode. Then the RAID function is Disabled. Hot Plug (for Serial SATA Port 0/1/2/3)
Enable/Disable Hot Plug support for Serial ATA Port 0/1/2/3. Default setting is disabled and cannot be allows access the RAID setup utility at boot time. Straggered Spin Up (for Serial SATA Port 0/1/2/3)
On an edge detect from 0 to 1, the...
Manual - Page 59
...Setup Default setting is Enabled. When set to Disabled, displays no configuration for the serial port. IRQ=3/IO=3F8h;
When set to Auto allows the server's BIOS or OS to configure the serial port settings. Change Settings Change Serial Port 0/1 device settings... Settings Displays the Serial Port base I/O address and IRQ. Super IO Configuration
Super IO Chip Display the model name...
Manual - Page 61
...: parity bi is 0 if the num of 1's in the data bits is always 0. BIOS Setup Console redirection enables users to detect some transmission errors. Space: Parity bit is even. Mark and Space Parity do not allow for error detection.
(Note) Advanced items prompt when this item is odd. Odd: parity bit is0if num...
Manual - Page 62
...Support (Note)
Enable/Disable VT-UTF8 Combo Key Support. Default setting...Loader. The standard setting is Enabled. ...: Enabled/Disabled. Default setting is Disabled.
(Note... and Columns supported redirection. Options...setting is only available for remote management of a Windows Server OS through a serial port. Out-of-Bnad Mgmt Port
Microsoft Windows Emerency Management Service...
Manual - Page 63
... to Enabled. - 63 - Options available: Enabled/DIsabled. Default setting is Enabled.
(Note) This item appears when Network Stack is Disabled. Default setting is Enabled. Ipv4 PXE Support(Note)
Enable/Disable Ipv4 PXE feature.
Options available: Enabled/DIsabled. Options available: Enabled/DIsabled. BIOS Setup 2-2-11 Network Stack
Network stack
Enable/Disable UEFI network stack...
Manual - Page 68
... performance by masking the refresh cycles of operations in Memory Mode item. Mirroring/Sparing
Displays the current support memory mode. Current Memory Mode
Displays the current memory mode. Options available: Enabled/Disabled. BIOS Setup
- 68 - When set to Lockstep mode, the motherboard uses two areas of memory to trigger fail-over. Options available...
Manual - Page 69
... Disabled. Rank Margin Enable/Disable Rank Margin function. Default setting is Enabled. OLTT Peak BW % Press the numberic keys to view installed DIMM information.
- 69 - Options available: Auto/300 M/900 M/1500 M/.../OLTT/CLTT. Altitude Configure the Altitude value. Default setting is Enforce DIS. Enforce DIMM To enforce POR function. Default setting is 3000 M. BIOS Setup
Manual - Page 71
... available: 1G/2G/4G/8G/16G/32G/64G. Default setting is Disabled. Default setting is 0x80000000. Options available: Enabled/Disabled. Default setting is 64G. Default setting is Auto. Options available: Enabled/Disabled. Default setting is Enabled.
- 71 - BIOS Setup TargetVGA Display the Target VGA support informaiton. Options available: Onboard/Offboard. IOH Configuration Intel...
Manual - Page 74
... ROM or driver. 2-3-2 South Bridge Configuration
PCH Information Name/Stepping Information
Displays the name and stepping information of the south bridge.
Options available: Enabled/Disabled. When set to Last State, the system will return to the active power state prior to save the
last power state. Restore on the BMC setting. BIOS Setup
- 74...
Manual - Page 85
... trap during legacy boot. this option is useful when any RT code is Immediate.
- 85 - Options available: Force BIOS/Keep Current. INT19 Trap Response BIOS reaction on INT19 trapping by Option ROM Immediate: execute the trap right away. BIOS Setup Default setting is executed above 1MB. Always: Do not allow disabling GA20; Option...
Gigabyte GA-7PESVL Reviews
We have not received any reviews for Gigabyte yet.