Gigabyte 7NF-RZC Support and Manuals
Get Help and Manuals for this Gigabyte item
This item is in your list!
View All Support Options Below
Free Gigabyte 7NF-RZC manuals!
Problems with Gigabyte 7NF-RZC?
Ask a Question
Free Gigabyte 7NF-RZC manuals!
Problems with Gigabyte 7NF-RZC?
Ask a Question
Popular Gigabyte 7NF-RZC Manual Pages
User Manual - Page 3
...installation, please follow the instructions below: 1. Prior to installing the electronic components, please have a problem related to the use of violating the conditions recommended in the provided manual.
3. Installation...certified computer technician. Damage due to be an unofficial Gigabyte product. Prior to the installation of uncertified components. 5. Before using the product, ...
User Manual - Page 4
... CMOS Features ...21 Advanced BIOS Features ...23 Advanced Chipset Features 24 Integrated Peripherals ...25 Power Management Setup 27 PnP/PCI Configurations ...29 PC Health Status ...30 Load Fail-Safe Defaults ...31 Load Optimized Defaults ...31 Set Supervisor/User Password 32 Save & Exit Setup ...33 Exit Without Saving ...33
Chapter 3 Install Drivers 35
7NF-RZ Series Motherboard
- 4 -
User Manual - Page 5
... y System voltage detection y CPU / System temperature detection y CPU / System fan speed detection y Thermal shutdown function y Use of licensed AWARD BIOS y Supports Q-Flash y Supports @BIOS y Supports EasyTune y ATX form factor, 20cm x 30.5cm
(Note) DDR 400 can be supported through overclocking in BIOS. (Please refer to page 24 for detail settings.) "*" For 7NF-RZ only.
- 5 - Introduction
User Manual - Page 8
.../ 400MHz CPU, Default)
OFF
ON
OFF: 100MHz (supports FSB 200MHz CPU)
OFF
You must complete the following steps: Step 1- CLK_SW Default setting: ON
7NF-RZ Series Motherboard
- 8 - Install Memory Modules Step 4-
Install the Central Processing Unit (CPU) Step 3- English
Hardware Installation Process
To set up your computer, you must set CLK_SW to OFF (100MHz) when you used FSB...
User Manual - Page 14
... connector can connect to one IDE device as Slave (for information on settings, please refer to the instructions located on the IDE device).
39
1
IDE1
IDE2
40
2
7) PWR_LED... other as Master and the other end of FDD drives supported are: 360KB, 720KB, 1.2MB, 1.44MB and 2.88MB. Definition
1
1
MPD+
2
MPD-
3
MPD-
7NF-RZ Series Motherboard
- 14 -
Please connect the red ...
User Manual - Page 19
.../PCI Configurations ` PC Health Status
ESC: Quit F8: Q-Flash
Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving
KLJI: Select Item F10: Save & Exit Setup Time, Date, Hard Disk Type...
- 19 -
ENTERING SETUP Powering ON the computer and pressing immediately will allow you enter Award BIOS CMOS...
User Manual - Page 20
... setup page includes all CMOS value changes and exit setup.
7NF-RZ Series Motherboard
- 20 - English
If you can't find the setting you want, please press "Ctrl+F1" to CMOS and exit setup....configuration.
• Set Supervisor Password Change, set , or disable password. It allows you to limit access to the system and Setup, or just to Setup.
• Set User Password Change, set , or disable...
User Manual - Page 21
...labeled on the outside drive casing. You can manually input the correct settings
Access Mode Use this information.
For example, 1 p.m....of three methods:
Auto
Allows BIOS to set the access mode for the hard drive. BIOS Setup
Through Dec. Day
The day, from ... faster system start up. Manual User can use one of sectors
If a hard disk has not been installed, select NONE and press ...
User Manual - Page 23
... will not search for floppy disk drive to Setup page will not be any warning message if the drive installed is 360K.
(Default value)
Password Check
System
The system can not boot and can...by SCSI. Disabled
Select your boot device priority by ZIP. PCI
Set initial display first to PCI slot. (Default value)
AGP
Set initial display first to select the first initiation of floppy disk drive...
User Manual - Page 24
... (make sure FSB Frequency is set to 200MHz), set Memory Frequency to 100%.
7NF-RZ Series Motherboard
- 24 -
Auto
Set the best memory frequency for system. (Default value)
50MHz ~ 100MHz Set AGP frequency manually.
Please follow the instructions below to enable the support for DDR 400 memory modules : (You have to set System Performance to Manual). 1) If you use a processor...
User Manual - Page 25
...support. Disabled
Disable USB keyboard support. (Default value)
USB Mouse Support
Enabled
Enable USB mouse support.
If a hard disk controller
card is used, please set at "Disabled".
Enabled
Enable onboard 1st channel IDE port. (Default value)
Disabled
Disable onboard 1st channel IDE port. English
Integrated Peripherals
CMOS Setup... this function.
"*" For 7NF-RZ only.
- 25 ...
User Manual - Page 26
... ECP or ECP+EPP.
3
Set ECP mode use DMA to 3. (Default value)
1
Set ECP mode use DMA to 1.
7NF-RZ Series Motherboard
- 26 -
UR2 Duplex Mode
This feature allows you to ASKIR mode.
Disabled
Disable onboard Serial port 1.
English
Onboard Serial Port 1
Auto
BIOS will automatically setup the port 1 address.
3F8/IRQ4 Enable onboard...
User Manual - Page 27
...function. (Default value)
Midi Port IRQ 5 10
Set Midi Port IRQ to 10. (Default value)
Power Management Setup
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Power Management Setup
ACPI Suspend Type Soft-Off by PWR-BTTN PME ... Power off instantly. (Default value)
Delay 4 Sec. BIOS Setup
Soft-off by Keyboard x KB Power ON Password AC BACK Function
[S1(POS)] [Instant-off .
User Manual - Page 32
... enter Setup.
7NF-RZ Series Motherboard
- 32 - When enabled, the Supervisor password is required for the password every time the system is required to access only basic items. If you select "System" at the center of the screen to assist you in creating a password. You may access all BIOS Setup program function. English
Set Supervisor/User Password
CMOS Setup...
User Manual - Page 40
... : http://www.giga-byte.com.au
France GIGABYTE TECHNOLOGY FRANCES S.A.R.L. Tech. Support : http://tw.giga-byte.com/TechSupport/ServiceCenter.htm Non-Tech. Support(Sales/Marketing) : http://ggts.gigabyte.com.tw/nontech.asp WEB address : http://www.gigabyte.pl
7NF-RZ Series Motherboard
- 40 - LTD. English
China NINGBO G.B.T. TRADING CO., LTD. Support : http://www.giga-byte.com.au...
Gigabyte 7NF-RZC Reviews
Do you have an experience with the Gigabyte 7NF-RZC that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Gigabyte yet.
Earn 750 points for your review!