Installation Instructions
Page 1
... all of the 10-32 x 1.75 in -country support information, or contact Garmin (Europe) Ltd. Follow these guidelines for the swivel mount (bolts or screws) (page 3) Installation Preparation Before permanently installing any part of your echo 100/150/200/300c/500c /550c. by phone at (913) 397.8200 or (800) 800.1020. Tools Needed • Drill...
... all of the 10-32 x 1.75 in -country support information, or contact Garmin (Europe) Ltd. Follow these guidelines for the swivel mount (bolts or screws) (page 3) Installation Preparation Before permanently installing any part of your echo 100/150/200/300c/500c /550c. by phone at (913) 397.8200 or (800) 800.1020. Tools Needed • Drill...
Installation Instructions
Page 2
... over the hole and the cable, with marine sealant so that it extends beyond the bottom of tape around the hole and the cable. 4. Installing the Transom-Mount Hardware Notice Do not cut the transducer cable. Using a 5/32 in. (4 mm) bit, drill the pilot holes approximately 1 in. (25 mm) deep ...10123;, and mark the center location of the transom or the pass-through the transom after you installed the transducer, install the cable entry cover to keep water from the point of the bit to the echo device. • If you are routing the cable using the other sources of the transom ...
... over the hole and the cable, with marine sealant so that it extends beyond the bottom of tape around the hole and the cable. 4. Installing the Transom-Mount Hardware Notice Do not cut the transducer cable. Using a 5/32 in. (4 mm) bit, drill the pilot holes approximately 1 in. (25 mm) deep ...10123;, and mark the center location of the transom or the pass-through the transom after you installed the transducer, install the cable entry cover to keep water from the point of the bit to the echo device. • If you are routing the cable using the other sources of the transom ...
Installation Instructions
Page 3
... you marked in . (4 mm), with the appropriate washers and nuts. echo Installation Instructions 3 Properly align the gasket between the transducer mount and the body of the cable tie. ➎ ➊ ➌ ➋ ➍ 2. Installing the Swivel Mount 1. Screws or bolts with countersunk heads will attach the mount to run the power and transducer cables from the...
... you marked in . (4 mm), with the appropriate washers and nuts. echo Installation Instructions 3 Properly align the gasket between the transducer mount and the body of the cable tie. ➎ ➊ ➌ ➋ ➍ 2. Installing the Swivel Mount 1. Screws or bolts with countersunk heads will attach the mount to run the power and transducer cables from the...
Installation Instructions
Page 4
... inline fuse holder on the red wire. 2. Place the swivel-mount base ➊ on the device. 1. Fastening the Swivel Mount with marine ➋ sealant. ➎ ➊ Installing the echo Device in the correct ports on the mounting surface, and fasten it using the included 10 mm M6×1.... 9. Place the swivel mount ➌ on the cables are connected to Power 1. Place the swivel mount ➌ on the locking arm. With the locking arm ➊ in the upward position, place the echo 100/150/300c device ➋ or the echo 200/500c/550c cradle ➌ into...
... inline fuse holder on the red wire. 2. Place the swivel-mount base ➊ on the device. 1. Fastening the Swivel Mount with marine ➋ sealant. ➎ ➊ Installing the echo Device in the correct ports on the mounting surface, and fasten it using the included 10 mm M6×1.... 9. Place the swivel mount ➌ on the cables are connected to Power 1. Place the swivel mount ➌ on the locking arm. With the locking arm ➊ in the upward position, place the echo 100/150/300c device ➋ or the echo 200/500c/550c cradle ➌ into...
Installation Instructions
Page 5
... and lift it rests firmly in the water, turn on the cradle ports to the keying on the echo device. 2. Test the transom mount transducer installation in small increments. No cables connect directly to an echo 200/500c/550c device. 1 Compare the divot ➊ on the cable connector to identify the ➊ correct port. 2. Placing...
... and lift it rests firmly in the water, turn on the cradle ports to the keying on the echo device. 2. Test the transom mount transducer installation in small increments. No cables connect directly to an echo 200/500c/550c device. 1 Compare the divot ➊ on the cable connector to identify the ➊ correct port. 2. Placing...