Ganz Security Z8-D2V Support and Manuals
Get Help and Manuals for this Ganz Security item
View All Support Options Below
Free Ganz Security Z8-D2V manuals!
Problems with Ganz Security Z8-D2V?
Ask a Question
Free Ganz Security Z8-D2V manuals!
Problems with Ganz Security Z8-D2V?
Ask a Question
Popular Ganz Security Z8-D2V Manual Pages
Z8-D2_VD2 Series Operation Guide - Page 2
...as follows.
Intended Audience
This document is used to address practices not related to set and use OSD menu for : z Technical support engineers z Maintenance engineers
Symbol Conventions
The symbols that may result in minor or moderate...Issue V1.0 (2017-07-28)
ii
ganzsecurity.com Operation Guide
Contents
About This Document
Purpose
This document describes how to personal injury.
Z8-D2_VD2 Series Operation Guide - Page 6
Operation Guide
1 OSD Main Menu
: right
: OK button Step 2 Click the OK button to open the OSD main menu or end setup. Figure 1-2 shows the five buttons. z Press and hold...menu.
Figure 1-2 Five-button layout
The buttons have the following functions:
z SET: Press this button to open the OSD main menu or end setup.
----End
1.1.2 Camera Control Using Five Buttons
If your camera has four ...
Z8-D2_VD2 Series Operation Guide - Page 8
... V1.0 (2017-07-28)
4
ganzsecurity.com Procedure
Step 1 Press the UP or DOWN button to select EXPOSURE. Step 2 Press the LEFT or RIGHT button to set LENS to MANUAL or DC. Step 2 Press the OK button to open the EXPOSURE interface, as aperture, shutter, and gain.
The default value is...
Z8-D2_VD2 Series Operation Guide - Page 9
Operation Guide Figure 2-1 EXPOSURE interface
2 OSD Setting
Step 3 Set exposure parameters. Table 2-1 lists the exposure parameters.
Value range: 0-100
[Setting method] Press the LEFT or RIGHT button. [Default value] 40
Issue V1.0 (2017-07-28)
5
ganzsecurity.com Table 2-1 Exposure parameters
Parameter Meaning
Setup
SHUTTER
This parameter is used to adjust shutter manually for ...
Z8-D2_VD2 Series Operation Guide - Page 10
Operation Guide
2 OSD Setting
Parameter D-WDR
DEFOG
Meaning
Setup
Overexposure or missing dark details may occur when areas of low brightness and high brightness coexist in Figure 2-2. The OSD main menu interface is too strong. Step 2 Press the LEFT or RIGHT button to select BACKLIGHT. Select SAVE&END to save the settings and exit the...
Z8-D2_VD2 Series Operation Guide - Page 11
..., and press the LEFT or RIGHT button to set this parameter to open the area setup interface, as shown in Figure 2-3. Set DISPLAY to ON and press the OK button to ON or OFF.
Issue V1.0 (2017-07-28)
7
ganzsecurity.com Operation Guide Figure 2-2 HSBLC interface
2 OSD Setting
----End
Procedure
Step 1 Press the UP or...
Z8-D2_VD2 Series Operation Guide - Page 12
... REC are displayed, press the LEFT or RIGHT button to select AGAIN to complete the setting.
2. Step 5 Press the UP or DOWN button to select MODE, and press the LEFT or RIGHT button to set this parameter to set this parameter.
Operation Guide Figure 2-3 Area setup interface
2 OSD Setting
1. Then press the OK button to perform...
Z8-D2_VD2 Series Operation Guide - Page 13
...RETURN after setup, and press the OK button to return to open the BLC interface, as shown in Figure 2-5. Step 6 After all parameters are set this parameter.
2.
Issue V1.0 (2017-07-28)
9
ganzsecurity.com Set BACKLIGHT to...Press the UP or DOWN button to select AGC LEVEL, and press the LEFT or RIGHT button to set , press the UP or DOWN button to select RETURN, and press the OK button to return to ...
Z8-D2_VD2 Series Operation Guide - Page 14
... select AREA, and press the OK button to set this parameter. The default value is MIDDLE. Operation Guide Figure 2-5 BLC interface
2 OSD Setting
Procedure
Step 1 Press the UP or DOWN button to select LEVEL, and press the LEFT or RIGHT button to open the area setup interface, as shown in Figure 2-6. The options are...
Z8-D2_VD2 Series Operation Guide - Page 15
... section 2.3.1 HSBLC."
----End
2.4 WHITE BAL
White balance is the same as shown in Figure 2-7. For details, see "Step 2 of the target object are ATW, AWG,
MANUAL WB, OUTDOOR, INDOOR, and AWC-SET. Operation Guide
2 OSD Setting
BLC area setup is intended to set this parameter.
2.
Z8-D2_VD2 Series Operation Guide - Page 18
...-28)
14
ganzsecurity.com Figure 2-11 Area setup interface
IR SMART area setup is the same as shown in Figure 2-11. Press the UP or DOWN button to select LEVEL, and press the LEFT or RIGHT button to open the area setup interface, as HSBLC area setup.
Operation Guide Figure 2-10 IR SMART interface
2 OSD Setting
1.
Z8-D2_VD2 Series Operation Guide - Page 24
Operation Guide Figure 2-17 MOTION interface
2 OSD Setting
Procedure
Step 1 Press the UP or DOWN button to select SELECT, and press the LEFT or RIGHT button to open the area setup interface, as shown in Figure 2-18.
Set DISPLAY to ON and press the OK button to select the desired area. Figure 2-18 Area setup interface...
Z8-D2_VD2 Series Operation Guide - Page 25
... press the LEFT or RIGHT button to open the ALARM interface, as HSBLC area setup. Step 6 Press the UP or DOWN button to select ALARM, and press the OK button to set this parameter. Operation Guide
2 OSD Setting
Motion area setup is the same as shown in Figure 2-19. For details, see "Step 2 of section...
Z8-D2_VD2 Series Operation Guide - Page 26
... RIGHT button to open the area setup area, as shown in Figure 2-21. Set PRIVACY to ON and press the OK button to set this parameter.
The default value is COLOR. Set DISPLAY to a value other than ...open the PRIVACY interface, as shown in Figure 2-20.
Operation Guide
2 OSD Setting
2.7.4 PRIVACY
Press the UP or DOWN button to select PRIVACY, and press the LEFT or RIGHT button...
Z8-D2_VD2 Series Operation Guide - Page 27
...button to select LANGUAGE, and press the LEFT or RIGHT button to open the DEFECT interface, as HSBLC area setup. The default value is 1.00. The options are WHITE, USER, CYAN, GREEN, BLUE, RED, and BLACK... value is WHITE. For details, see Step 2 of section 2.3.1 "HSBLC." Operation Guide Figure 2-21 Area setup interface.
2 OSD Setting
Privacy area setup is the same as shown in Figure 2-22.
Ganz Security Z8-D2V Reviews
We have not received any reviews for Ganz Security yet.