Manual/User Guide
Page 6
... gives an overview of seven chapters and sections explaining the special terminology and abbreviations used in this manual. These drives have a built-in controller that the reader has a basic knowledge of hard disk drives and their implementations in computer systems. This manual consists of the MHL Series and MHM Series and describes their...
... gives an overview of seven chapters and sections explaining the special terminology and abbreviations used in this manual. These drives have a built-in controller that the reader has a basic knowledge of hard disk drives and their implementations in computer systems. This manual consists of the MHL Series and MHM Series and describes their...
Manual/User Guide
Page 10
... personal injury if the user does not perform the procedure correctly. Damage: Do not press the cover of the disk drive. Do not touch the printed circuit board, but hold it too hard, the cover and the spindle motor contact, which may cause damage to the predate or other property, may occur... if the user does not perform the procedure correctly. Ensure that the disk drive is not affected by the edges. C141-E104-03EN...
... personal injury if the user does not perform the procedure correctly. Damage: Do not press the cover of the disk drive. Do not touch the printed circuit board, but hold it too hard, the cover and the spindle motor contact, which may cause damage to the predate or other property, may occur... if the user does not perform the procedure correctly. Ensure that the disk drive is not affected by the edges. C141-E104-03EN...
Manual/User Guide
Page 22
The MHL Series and MHM Series are 2.5-inch hard disk drives with built-in this chapter, and specifications and power requirement are described. CHAPTER 1 Device Overview 1.1 Features 1.2 Device Specifications 1.3 Power Requirements 1.4 Environmental Specifications 1.5 Acoustic Noise 1.6 Shock and Vibration 1.7 Reliability 1.8 Error Rate 1.9 Media Defects Overview and features are described in disk controllers. C141-E104-03EN 1-1 These disk drives use the AT-bus hard disk interface protocol and are compact and reliable.
The MHL Series and MHM Series are 2.5-inch hard disk drives with built-in this chapter, and specifications and power requirement are described. CHAPTER 1 Device Overview 1.1 Features 1.2 Device Specifications 1.3 Power Requirements 1.4 Environmental Specifications 1.5 Acoustic Noise 1.6 Shock and Vibration 1.7 Reliability 1.8 Error Rate 1.9 Media Defects Overview and features are described in disk controllers. C141-E104-03EN 1-1 These disk drives use the AT-bus hard disk interface protocol and are compact and reliable.
Manual/User Guide
Page 32
C141-E104-03EN 2-1 CHAPTER 2 Device Configuration 2.1 Device Configuration 2.2 System Configuration This chapter describes the internal configurations of the hard disk drives and the configuration of the systems in which they operate.
C141-E104-03EN 2-1 CHAPTER 2 Device Configuration 2.1 Device Configuration 2.2 System Configuration This chapter describes the internal configurations of the hard disk drives and the configuration of the systems in which they operate.
Manual/User Guide
Page 38
CHAPTER 3 Installation Conditions 3.1 Dimensions 3.2 Mounting 3.3 Cable Connections 3.4 Jumper Settings This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives. C141-E104-03EN 3-1
CHAPTER 3 Installation Conditions 3.1 Dimensions 3.2 Mounting 3.3 Cable Connections 3.4 Jumper Settings This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives. C141-E104-03EN 3-1
Manual/User Guide
Page 45
...following cautions, and handle the HDD under the safety environment. 3-8 C141-E104-03EN Installation Conditions (5) Service area Figure 3.6 shows how the drive must be accessed (service areas) during and after installation. Pressing it by external magnetic fields. Do not touch the printed circuit board, but... hold it too hard, the cover and the spindle motor contact, which may cause damage to the disk drive. Static: When handling the device, disconnect the body ground (500 kΩ or greater). Mounting...
...following cautions, and handle the HDD under the safety environment. 3-8 C141-E104-03EN Installation Conditions (5) Service area Figure 3.6 shows how the drive must be accessed (service areas) during and after installation. Pressing it by external magnetic fields. Do not touch the printed circuit board, but... hold it too hard, the cover and the spindle motor contact, which may cause damage to the disk drive. Static: When handling the device, disconnect the body ground (500 kΩ or greater). Mounting...
Manual/User Guide
Page 148
... attribute value data is in progress. • Off-line data collection capability Indicates the method of off-line data collection carried out by hard or soft reset. Bits 1 to a media after the previously set operation. Self-test has been stopped by an unknown meaning. Self-.... Bit 1: The device automatically saves the attribute value data to 7: Reserved bits C141-E104-03EN 5-71 Self-test has been suspended by the drive. Bit Meaning 0 Indicates that Execute Off-Line Immediate is supported. 1 Vendor unique 2 Indicates that off-line data collection being executed is aborted...
... attribute value data is in progress. • Off-line data collection capability Indicates the method of off-line data collection carried out by hard or soft reset. Bits 1 to a media after the previously set operation. Self-test has been stopped by an unknown meaning. Self-.... Bit 1: The device automatically saves the attribute value data to 7: Reserved bits C141-E104-03EN 5-71 Self-test has been suspended by the drive. Bit Meaning 0 Indicates that Execute Off-Line Immediate is supported. 1 Vendor unique 2 Indicates that off-line data collection being executed is aborted...
Manual/User Guide
Page 221
...operation to the disk medium of the previous command. If the received command is a "sequential write" (data to data of previous command), the drive starts data transfer and receives data of sectors requested by a write command is physically sequent the data of previous command and random write operation is... an interrupt of command complete after completion of data transfer requested by the host system. The drive receives the next command continuously. Even if a hard reset or soft reset is received or the write cache function is disabled by the host are written on the disk medium, actual...
...operation to the disk medium of the previous command. If the received command is a "sequential write" (data to data of previous command), the drive starts data transfer and receives data of sectors requested by a write command is physically sequent the data of previous command and random write operation is... an interrupt of command complete after completion of data transfer requested by the host system. The drive receives the next command continuously. Even if a hard reset or soft reset is received or the write cache function is disabled by the host are written on the disk medium, actual...
Manual/User Guide
Page 228
... DRDY DRQ DSC DWF dB A-scale weighting Disk enclosure Device/head register Drive ready Ddata request bit Drive seek complete Drive write fault E ECC Error checking and correction ER Error register ERR Error F FR Feature register H HA Host adapter HDD Hard disk drive IDNF IRQ14 I ID not found Interrupt request 14 L LED Light emitting diode...
... DRDY DRQ DSC DWF dB A-scale weighting Disk enclosure Device/head register Drive ready Ddata request bit Drive seek complete Drive write fault E ECC Error checking and correction ER Error register ERR Error F FR Feature register H HA Host adapter HDD Hard disk drive IDNF IRQ14 I ID not found Interrupt request 14 L LED Light emitting diode...