Fluke 190-104/AM Support and Manuals
Get Help and Manuals for this Fluke item
View All Support Options Below
Free Fluke 190-104/AM manuals!
Problems with Fluke 190-104/AM?
Ask a Question
Free Fluke 190-104/AM manuals!
Problems with Fluke 190-104/AM?
Ask a Question
Popular Fluke 190-104/AM Manual Pages
Product Manual - Page 1
...dc to 10 V dc or a current loop of 1 V dc to 20 mA (with additional shunt). Specifications are trademarks of up to two dc voltage inputs in the range of 4 mA to 1000 V dc can...for the 17xx Power and Energy Loggers. Auxiliary Input Adapter
for 17xx Power and Energy Loggers
Instructions
Introduction
The Auxiliary Input Adapter (or Product) is an accessory for other applications such as solar...
Product Manual - Page 2
... personal injury:
• Read all safety information before you use the Product.
• Carefully read all instructions.
• Use the Product only as specified, or the protection supplied by the Product can cause damage to the user. MyFlukeStore e products online at: www.
.com 1.888.6 Safety Information
A Warning identifies conditions and procedures that...
Product Manual - Page 3
... indicator shows. Check test lead continuity.
• Remove the input signals before you clean the Product.
• Use only cables with local and national safety codes. MyFlukeStore e products online at: www.
.com 1.888.6
• Comply with correct voltage ratings.
• Do not exceed the Measurement Category (CAT) rating of the lowest...
Product Manual - Page 4
... connected directly to utilization points (socket outlets and similar points) of the low-voltage MAINS installation.
Measurement Category III is applicable to test and measuring circuits connected to the distribution part of electric shock.
Consult user documentation.
HAZARDOUS VOLTAGE. Product Category: With reference to test and measuring circuits connected at : www...
Product Manual - Page 5
... e products online at: www.
.com 1.888.6 Open the grommet strain relief and remove the dummy plug D. Note The dummy plug or a cable must be installed to achieve the ingress protection of IP50.
Product Manual - Page 6
.... 10. Configure the AUX channel on the safety socket inputs. Note Pay attention to the Logger.
3. Voltage Divider Input 1 V DC to Custom 5), and use these settings:
• Sensor: 0-10 V • Unit: V • Minimum: 0 V • Maximum: 1000 V
MyFlukeStore e products online at the same time. Insert the sensor cable through the strain relief...
Product Manual - Page 7
....
How to ±1000 V dc Input Impedance 20 MΩ (see block diagram for details) Connector 4 mm safety socket
MyFlukeStore e products online at: www.
.com 1.888.6 Specifications
General
Calibration Cycle 2 years Warranty 1 year Dimensions 119 mm x 86 mm x 38 mm
(4.69 in x 3.39 in x 1.5 in) Weight 280 g (0.6 lb) Output Cable Length .......... 1.9 m (6.2 ft...
Product Manual - Page 8
Accuracy
Input
Range
Intrinsic Accuracy Aux Adapter + Instrument
(% of Reading + % of Range)
Direct Input
±10 V
see instrument specification
Voltage divider input ±1000 V ±(0.5% + 0.002%)
Note:
Environmental Reference Conditions: 23 °C ±5 °C, instrument operating for at least 30 minutes, no external electrical/magnetic field, RH
Product Manual - Page 10
... implied warranty or of incidental or consequential damages, this limitation of the problem.
P.O. Box 1186 5602 BD Eindhoven The Netherlands
11/99
MyFlukeStore e products online at: www.
.com 1.888.6 To obtain service during the warranty period, contact your nearest Fluke authorized service center to obtain return authorization information, then send the product to that...
Fluke 190-104/AM Reviews
We have not received any reviews for Fluke yet.