Fluke 116-NIST Support and Manuals
Get Help and Manuals for this Fluke item
View All Support Options Below
Free Fluke 116-NIST manuals!
Problems with Fluke 116-NIST?
Ask a Question
Free Fluke 116-NIST manuals!
Problems with Fluke 116-NIST?
Ask a Question
Popular Fluke 116-NIST Manual Pages
Fluke 116 Users Manual - Page 1
All rights reserved. Printed in China All product names are trademarks of their respective companies. ®
116
True-rms Multimeter
Users Manual
PN 2538688 July 2006, Rev. 1, 2/07
© 2006, 2007 Fluke Corporation.
Fluke 116 Users Manual - Page 2
.../99
Fluke Corporation P.O. FLUKE IS ...Service Center with a description of purchase. To obtain service during the warranty period, contact your nearest Fluke authorized service... center to obtain return authorization information, then send the product to extend any other warranty on Fluke...IMPLIED. Fluke Europe B.V. Box...
Fluke 116 Users Manual - Page 3
... in fixed-equipment installations at the distribution level.
The IEC 61010-1 2nd Edition safety standard defines four measurement categories (CAT I to protect against transients in the world: +1-425-446-5500 Visit Fluke's web site at register.fluke.com.
When making...presence of danger from transient impulses. True-rms Multimeter
Introduction
The Fluke Model 116, is unspecified.
1
Fluke 116 Users Manual - Page 4
...circuit power and discharge all high-voltage capacitors before opening the battery door or Meter case.
2 116 Users Manual
Safety Information A "XWWarning" statement identifies hazardous conditions and actions that have been approved by a ... not operating
properly. • Always use test leads that have the Meter
serviced. • Do not apply more than the rated voltage, as the meter
and that...
Fluke 116 Users Manual - Page 5
... Check the test leads for disposal.
3 Contact Fluke or a qualified recycler for continuity before use the Auto Volts function to manual
J Earth ground
D AC and DC
~ Do... not dispose of this function's low input impedance (≈3 kΩ). Refer to measure voltages in hazardous areas. • Avoid working alone. • Use only the replacement...
Fluke 116 Users Manual - Page 6
... present reading.
4
B
R
The Meter function is a negative value.
E
K
Display hold enabled. Measured input voltage ≥ 30 V, or voltage overload condition (OL).
D
Y
X Unsafe voltage. 116 Users Manual
Display
5 4 3 2 1
14 13
6 12 15
7
9
8
10
11 16
eeo02f.eps
No. Symbol
Meaning
A
s
The Meter function is set to Diode Test
C
O
Input is set to Continuity.
Fluke 116 Users Manual - Page 7
....
User sets the Meter's range.
VWX Maximum, minimum, average or present reading displayed
G
LoZ
The Meter is in the Auto Volts function. K
610000 mV Indicates the Meter's range selection. M
Auto Volts The Meter is measuring voltage or capacitiance with a low input impedance. Auto
Auto ranging.
True-rms Multimeter Display
No.
Manual
Manual ranging...
Fluke 116 Users Manual - Page 8
... be repaired before the Meter will operate. Internal error.
Internal error.
The Meter must be repaired before the Meter will operate. bAtt CAL Err EEPr Err F11Err
Error Messages Battery must be replaced before it will operate. Meter calibration is required before it will operate.
6 Calibration required. B
Input terminal for all measurements. 116 Users Manual...
Fluke 116 Users Manual - Page 10
...exit and erase stored readings, press p for 20 minutes. The backlight
automatically turns off . 116 Users Manual
Battery Saver ("Sleep Mode") The Meter automatically enters "Sleep mode" and blanks the display ...range yourself.
To exit and return to toggle the backlight on . Manual and Autoranging The Meter has both Manual and Autorange modes.
• In the Autorange mode, the Meter selects...
Fluke 116 Users Manual - Page 14
.... Flame sensor probe
Control Module
eeo08f.eps
To measure flame rectification circuits:
1. Connect the Meter between the flame sensor probe and the control module.
3. 116 Users Manual
Measuring AC and DC Current WWarning
To avoid personal injury or damage to the Meter:
• Never attempt to make an in-circuit current measurement...
Fluke 116 Users Manual - Page 16
... Impedance Capacitance Measurements
For making capacitance measurements on cables with ac volts only.
2. 116 Users Manual
Measuring Frequency XWWarning
To avoid electrical shock, disregard the bar graph for all ranges.... turning on and off or goes into LoZ, (low input impedance) Capacitance mode.
This setting is not saved when the Meter is 0 V for frequencies >1 kHz. edy09f.eps
14...
Fluke 116 Users Manual - Page 18
...consists of the scale.
The bar graph is relative to the middle of replacing the battery and cleaning the case. 116 Users Manual
Using the Bargraph The bar graph is useful for example (see below),... the major divisions on the scale represent 0, 15, 30, 45, and 60 V. Because the bar graph updates much...
Fluke 116 Users Manual - Page 20
Extended specifications are available at 0 % to + 60 °C Temperature Coefficient 0.1 x (specified accuracy)/°...Pollution Degree 2
Display Digital: 6,000 counts, updates 4/sec Bar Graph: 33 segments, updates 32/sec Temperature Operating: -10 °C to + 50 °C
Storage: -40 °C to 90 %. 116 Users Manual
General Specifications Accuracy is specified for 1 year after calibration,...
Fluke 116 Users Manual - Page 22
detects opens or shorts of Reading] + [Counts])
Beeper on < 20 Ω, off > 250 Ω; 116 Users Manual
Function Continuity
Ohms
Diode test Capacitance Lo-Z Capacitance Temperature (Type K Thermocouple)
Table 1 Accuracy Specifications (cont.)
Range
600 Ω
600.0 Ω 6.000 kΩ 60.00 kΩ 600.0 kΩ 6.000 MΩ 40.00 MΩ 2.000 V
Resolution
1 Ω
0.1 Ω 0.001...
Fluke 116 Users Manual - Page 24
Input Characteristics
Input Impedance (Nominal)
>5 MΩ 10 MΩ 60 dB at dc, 50 or 60 Hz >100 dB at dc, 50 or 60 Hz
~3 kΩ 60 dB at dc, 50 or 60 Hz
Open Circuit Test Voltage 116 Users Manual
Function Volts AC Volts DC Auto-V LoZ
Ohms Diode Test
Table 2.
Fluke 116-NIST Reviews
We have not received any reviews for Fluke yet.