Fluke 281-U Support and Manuals
Get Help and Manuals for this Fluke item
Popular Fluke 281-U Manual Pages
Product Manual - Page 10
... the Utility Menu 14-1
Introduction...14-2 Storing and Recalling Set-ups 14-2 Channel Waveform Information 14-2 Warnings and Error messages 14-3 Remote Interface Set-up 14-3 Reference Clock In/Out Setting 14-3 Cursor/Marker Output 14-3 Power On Setting 14-4 System Information 14-4
viii
MyFlukeStore Shop for Fluke products online at: www.
.com 1.888.610.7664
Product Manual - Page 15
... set -up keys or output connections for Fluke products online at: www.
.com 1.888.610.7664 and four-channel arbitrary waveform generators. These instruments can define arbitrary waveforms with any of waveforms between the different models when describing the functions associated with 12 bit vertical resolution and from 4 to two-
To avoid repetition specific...
Product Manual - Page 23
...set -ups may be triggered by rotary control.
Value entry direct by numeric keys or by the previous or next channel.
Environmental:
Indoor use at : www.
.com 1.888.610.7664 Safety:
Complies with EN61326. Installation category II
Model 281
Model 282
Model...lb)
7.2 kg (16 lb)
1-10
MyFlukeStore Shop for Fluke products online at altitudes up . Inter-channel Triggering
Any ...
Product Manual - Page 32
...set to do this is the channel currently enabled for Fluke products online at the bottom left of the channel selected by using the generator for a particular environment by the SETUP keys; The power-up the generator displays the installed...change the basic generator parameters for optimum contrast.
281, 282, 284
Users Manual
Introduction
This section is a general introduction to ...
Product Manual - Page 34
...pressing the setup...
soft-key on the bottom line brings up the screen shown below :
MODE: continuous gated triggered
setup... For example, pressing FILTER brings up the TRIGGER SETUP menu;
...between its two possible settings of the channel currently enabled for Fluke products online at the STD (standard waveform) and UTILITY screens. 281, 282, 284
Users Manual
Note
On multi-channel...
Product Manual - Page 42
.../TTL level output that can be automatically or manually set -up can be selected for arbitrary waveforms only. 281, 282, 284
Users Manual
choose to change the output level or the offset... Shop for Fluke products online at the main waveform frequency, or a pulse coincident with the first few points of an arbitrary waveform. The default set to restore last setup. The error menu is left...
Product Manual - Page 45
... in length;
281, 282, 284
Users Manual
Introduction
Principles of...is set up to external when you must be one set ...SETUP screen (accessed by pressing the SWEEP front panel key), or by manually... pressing the MAN TRIG key.
The cursor/marker polarity and level is turned on and off by the on or off soft-key on . The generator does not provide a ramp output for Fluke...
Product Manual - Page 46
... frequencies but see Sweep Type below for Fluke products online at once using the appropriate soft-key.
In addition the control screen for setting up the range, time (sweep rate),... 1.888.610.7664 6 Sweep Operation
Setting Sweep Parameters
Setting Sweep Parameters
Pressing the SWEEP key (or the sweep setup... soft-key on /off soft-key. manual...
On all waveforms is selected from ...
Product Manual - Page 48
... to the stop frequency depending on the SWEEP SETUP screen calls the MANUAL SWEEP FREQ screen:
MANUAL SWEEP FREQ:
1.630 MHz
step fast
wrap
step slow
done
Before manual control can not select step fast when the number of the waveform when the next trigger is set to on the front panel, or a remote command...
Product Manual - Page 101
... Menu
Introduction...14-2 Storing and Recalling Set-ups 14-2 Channel Waveform Information 14-2 Warnings and Error messages 14-3 Remote Interface Set-up 14-3 Reference Clock In/Out Setting 14-3 Cursor/Marker Output 14-3 Power On Setting 14-4 System Information 14-4 Calibration ...14-5 Copying Channel Set-ups 14-5
14-1
MyFlukeStore Shop for Fluke products online at: www.
.com...
Product Manual - Page 120
... be returned to load the system defaults. If for Fluke products online at: www.
.com 1.888.610.7664
nn has been set )
Standard Event Status Enable Register † = 0
Execution Error Register
= 0
Query Error Register
= 0
Parallel Poll Enable Register †
= 0
† Registers marked thus are specific to the GPIB section of the instrument and are determined...
Product Manual - Page 131
... additional action. Query and clear execution error number register. The register is .
The syntax of the Service Request Enable Register in numeric format.
The response format is . 281, 282, 284
Users Manual
*ESR?
*IDN?
*IST? *OPC
*OPC?
*PRE *PRE? *SRE *SRE? *STB? *WAI *TST? The syntax of the software installed. The syntax of the response...
Product Manual - Page 135
... from start address to stop address . Move the data in arbitrary waveform to channel .
Query and clear execution error number register. Force a trigger to Volts. Set hold mode , , or .
16-24
MyFlukeStore Shop for Fluke products online at address in arbitrary waveform from start address to stop address by the offset .
ARBLISTCH? Change...
Product Manual - Page 146
B Appendices
Warning and Error Messages
145 Selected mode is not available when phase lock master or slave 146 Cannot delete arbs while a sequence is running 147 Current set-up requires an arb wfm which does not exist 148 Trig/gate mode and seq step value cause a trigger conflict 149 Seq step value can...
Product Manual - Page 147
281, 282, 284
Users Manual
Remote Warnings 72 Length is illegal or pattern too long 177 Illegal remote calibration command. 185 Command not available while sweeping. B-4
MyFlukeStore Shop for RS232 170 Length value error...in the ARBDEF(CSV) command
Remote Errors 120 Waveform limit value out of range... mode 165 Cannot set waveform frequency or period for a sequence 166 Cannot set sample frequency or...
Fluke 281-U Reviews
We have not received any reviews for Fluke yet.