Fluke 294-U Support and Manuals
Popular Fluke 294-U Manual Pages
User Manual - Page 12
... Panel G-2 G-3. Status Model...17-9 1-1. 291, 292, 294
Users Manual
Modulation Commands 17-19 Synchronizing Commands 17-19 Status Commands 17-19 Miscellaneous Commands 17-21 Remote Command Summary 17-22
18 Maintenance 18-1
Introduction...18-2 Cleaning ...18-2
Appendices
A AC Supply Voltage A-1 B Warning and Error Messages B-1 C SYNC OUT Automatic Settings C-1 D Factory System...
User Manual - Page 34
...e.g.
291, 292, 294
Users Manual
Introduction
This section is...error, battery fault or firmware updated will light to any time with changes of ambient temperature or viewing angle but can recall the status screen at any of the front panel. At power-up settings...SETUP keys; If an error is located at power-down or to show that of Editing". The power-up the generator displays the installed...
User Manual - Page 35
...-to-channel synchronization and set-up parameters, error message settings and store/recall set-ups to/from the ...manual triggering (when TRIG IN is appropriately set) and for synchronizing two or more detail in the next section.
• The STATUS key always returns the display to the default start-up by direct numeric keyboard entry;
Parameter values can be controlled.
• The SETUP...
User Manual - Page 36
... by pressing the associated soft-key which will toggle the mode between its two possible settings of the rotary control) will increment or decrement the value;
the step size is...Repeated presses of the filter type. 291, 292, 294
Users Manual
Note On multi-channel instruments the channel to be edited must first be selected (i.e.
setup...
look, for editing. In screens where a ...
User Manual - Page 48
... can be set -up to investigate the frequency response of a circuit. Connections for use with an oscilloscope or hard-copy device to 1010:1).
spacing... time... 291, 292, 294
Users Manual
General
Principles...wide frequency range (up soft key on the MODE screen) displays the SWEEP SETUP screen:
SWEEP SETUP: off soft key on .
The MAIN OUT is connected to the circuit input and...
User Manual - Page 54
... event.
MODE: continuous gated triggered
off
setup... the interval between bursts is therefore 0·005 ms to the nearest available value, so that cannot be set using the level soft-key;
In triggered...runs whenever the gating signal is edge triggered. 291, 292, 294
Users Manual
General
Triggered burst and gated modes are selected from the MODE screen, called by the TRIG IN...
User Manual - Page 55
...or gate signal when external triggering or gating is on this screen accesses the TRIGGER/GATE SETUP
7-3 Adjacent Channel Trigger Output On multi-channel instruments the trigger out signal of the next... source: wfm end
The TRIGGER OUT choices are channels 2 and 4 adjacent to manual using the rotary control. To set high or low. Trigger out is necessary to change the mode from auto to ...
User Manual - Page 56
... to initiate a burst. this generator is set -up screen called by the internal trigger generator or an adjacent channel's trigger out. In multi-channel instruments pressing MAN TRIG will trigger all those channels for triggering by pressing setup on the MODE screen.
291, 292, 294
Users Manual
screen on which man has been selected...
User Manual - Page 57
...set up such that channel's TRIGGER IN screen. this is the case the actual phase is fixed at the end of triggered bursts never starts. The phase resolution of 0·1 ° but below this problem... clock
0 ° only
Manual Initialization of Inter-Channel Triggering
If a multi-channel instrument is recalculated. waveforms are changed the waveform is set with a precision of true ...
User Manual - Page 126
....pdf file with the correct driver installed, there will install the appropriate driver. 291, 292, 294
Users Manual
Full List of the software installation procedure. USB Interface
The USB interface allows the instrument to a PC, with information and details of Addressable RS232 Interface Control Codes
02H Set Addressable Mode. 03H Universal Unaddress control code. 04H Lock Non-Addressable...
User Manual - Page 130
...at power on are determined on :
Status Byte Register
= 0
Service Request Enable Register †
= 0
Standard Event Status Register
= 128 (pon bit set)
Standard Event Status Enable Register † = 0
Execution Error Register
= 0
Query Error Register
= 0
Parallel Poll Enable Register †
= 0
† Registers marked thus are specific to the GPIB section of the instrument and are...
User Manual - Page 140
...292, 294
Users Manual
*IDN?
*IST? *OPC
*OPC?
*PRE *PRE? *SRE *SRE? *STB? *WAI *TST? EER? The syntax of the Service Request Enable Register in numeric format. Query and clear execution error number ...nr1. This will be available immediately the command is . Set the Parallel Poll Enable Register to . Query and clear query the error number register. Returns the value of the response is 1....
User Manual - Page 142
...Set the Service Request Enable Register to local operation and unlocks the keyboard. 291, 292, 294
Users Manual...
17-22
LOCAL
Returns the instrument to . UCBID?
Returns the value in the Standard Event Status Register in force. Returns the complete set up of the Service...Set the Standard Event Status Enable Register to the value .
Set... the instrument set up contained in...
User Manual - Page 144
... by the offset .
Query and clear execution error number register. 291, 292, 294
Users Manual
17-24
ARBINSSTD ,, ,
ARBINVERT ,,
ARBLEN?... no card). Set the arbitrary sample clock freq to sec.
Set the arbitrary sample clock period to Hz. Set the output filter... arbitrary waveform between start address/data / to .
Set the burst count to , , or . Set the dc offset to , , , or ....
User Manual - Page 157
... (mode: master/freq) but the frequencies are locked the mode will cause this error: 1. A synchronized channel is not set sample frequency or period for std waveforms 167 dBm output units assume a 50 Ohm... load sts 198 Memory card is off . This error does not set the frequency too high during synchronization. Cannot create WAVES or SETUP directory 195 Sequence segment number out of range min ...
Fluke 294-U Reviews
Do you have an experience with the Fluke 294-U that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Fluke yet.
Earn 750 points for your review!