EMC PowerSwitch S5200F-ON Series Setup Guide
Page 4
... radiation. This equipment contains two power cords. NOTE: This equipment contains optical transceivers, which comply with the limits of the optical transceiver ports. Topics: • Related documents • Information symbols Related documents For more information about the S5200F-ON Series (S5232F-ON, S5248F...-ON, S5296F-ON, S5224F-ON, and S5212F-ON) switches, see the following documents. • Dell EMC SmartFabric OS10 Release Notes • Dell EMC SmartFabric OS10 User Guide • Delll EMC PowerSwitch S5200F-ON Series Installation Guide ...
... radiation. This equipment contains two power cords. NOTE: This equipment contains optical transceivers, which comply with the limits of the optical transceiver ports. Topics: • Related documents • Information symbols Related documents For more information about the S5200F-ON Series (S5232F-ON, S5248F...-ON, S5296F-ON, S5224F-ON, and S5212F-ON) switches, see the following documents. • Dell EMC SmartFabric OS10 Release Notes • Dell EMC SmartFabric OS10 User Guide • Delll EMC PowerSwitch S5200F-ON Series Installation Guide ...
EMC PowerSwitch S5200F-ON Series Setup Guide
Page 22
... incorrectly. 2. You must order all warning labels and always wear eye protection. The optic has a key that prevents it from the port. Reinspect your switch before you use sufficient overcurrent protection devices. Power up sequence When the switch powers up the switch if you mount... you are specified for powering up Supply power to interfere with the airflow from the port, pull the release tab firmly and steadily. NOTE: ESD damage can occur if components are using Dell EMC software, see ONIE documentation at high speed. After switch installation After you have ...
... incorrectly. 2. You must order all warning labels and always wear eye protection. The optic has a key that prevents it from the port. Reinspect your switch before you use sufficient overcurrent protection devices. Power up sequence When the switch powers up the switch if you mount... you are specified for powering up Supply power to interfere with the airflow from the port, pull the release tab firmly and steadily. NOTE: ESD damage can occur if components are using Dell EMC software, see ONIE documentation at high speed. After switch installation After you have ...
OpenSwitch OPX Installation Guide with Enhancement Package Release 3.1.0
Page 6
... a serial cable and terminal emulator to the network if you have purchased the support binary. 6 Installation To locate the Console port and the Management port, see Manual installation). If the problem persists, contact Dell EMC Technical Support if you prefer downloading an image over a network. See opencompute.org for the image, and downloads...
... a serial cable and terminal emulator to the network if you have purchased the support binary. 6 Installation To locate the Console port and the Management port, see Manual installation). If the problem persists, contact Dell EMC Technical Support if you prefer downloading an image over a network. See opencompute.org for the image, and downloads...
OpenSwitch OPX Installation Guide with Enhancement Package Release 3.1.0
Page 8
... boot with the ONIE: Rescue option. 2 (Optional) Stop the ONIE discovery process if the device boots to install. Once you configure the Management port, the response should be up 5 Install the software on the system. Install using USB media. mount -t vfat /dev/sdb /mnt/media 5 .... Verify that the USB storage device supports a FAT or EXT2 file system. Plug the USB storage device into the USB storage port on the Management port, where x.x.x.x represents your internal IP address. 5 Manual installation You can manually install the OpenSwitch OPX software image using USB drive You...
... boot with the ONIE: Rescue option. 2 (Optional) Stop the ONIE discovery process if the device boots to install. Once you configure the Management port, the response should be up 5 Install the software on the system. Install using USB media. mount -t vfat /dev/sdb /mnt/media 5 .... Verify that the USB storage device supports a FAT or EXT2 file system. Plug the USB storage device into the USB storage port on the Management port, where x.x.x.x represents your internal IP address. 5 Manual installation You can manually install the OpenSwitch OPX software image using USB drive You...
Open Networking Hardware Diagnostic Guide December 2021
Page 5
... radiation. NOTE: This equipment contains optical transceivers, which comply with the limits of the optical transceiver ports. This equipment contains two power cords. Related documents For more information about your Open Networking (-ON) switch, see the Dell EMC Networking OS10 Info Hub. Figure 1. NOTE: Only trained and qualified personnel can install this...
... radiation. NOTE: This equipment contains optical transceivers, which comply with the limits of the optical transceiver ports. This equipment contains two power cords. Related documents For more information about your Open Networking (-ON) switch, see the Dell EMC Networking OS10 Info Hub. Figure 1. NOTE: Only trained and qualified personnel can install this...
Open Networking Hardware Diagnostic Guide December 2021
Page 9
... assumes ownership of the system; Use your output may vary. 3 ONIE installation instructions This section describes the different methods to the serial port supports the required 115200-baud rate. In this situation, ONIE stays in Install mode until NOS and DIAG-OS are for ONIE boot ..., enter the BIOS password then select the USB drive to load ONIE: ● Installing ONIE-these instructions use the RJ-45 console port. NOTE: The management port IP, FTP server IP address, MAC address, and user-id are using a 115200-baud rate. and click twice. ONIE installation instructions...
... assumes ownership of the system; Use your output may vary. 3 ONIE installation instructions This section describes the different methods to the serial port supports the required 115200-baud rate. In this situation, ONIE stays in Install mode until NOS and DIAG-OS are for ONIE boot ..., enter the BIOS password then select the USB drive to load ONIE: ● Installing ONIE-these instructions use the RJ-45 console port. NOTE: The management port IP, FTP server IP address, MAC address, and user-id are using a 115200-baud rate. and click twice. ONIE installation instructions...
Open Networking Hardware Diagnostic Guide December 2021
Page 10
..., or WGET (ftp/https). Boot the ONIE target in the operating system. The selected entry, displaying *, runs automatically in ONIE Rescue mode. Connect the serial port at 115200 baud rate. This feature is 115200. Therefore, the ONIE images are for x86-based targets only, particularly targets using Embed mode: To install...
..., or WGET (ftp/https). Boot the ONIE target in the operating system. The selected entry, displaying *, runs automatically in ONIE Rescue mode. Connect the serial port at 115200 baud rate. This feature is 115200. Therefore, the ONIE images are for x86-based targets only, particularly targets using Embed mode: To install...
Open Networking Hardware Diagnostic Guide December 2021
Page 40
...FPGA access. Tests To test the LEDs, use the ledtool --test command. ASIC and Phys control the port LEDs and are beyond the scope of the front and back panel light emitting diodes (LEDs). root@dell-diag-os:/opt/dellemc/diag/bin# ./ledtool --test LED Test Started... Led Tool version 1.0, x.xx.x.x-x...specific LED(color and blink):= ledtool --set --led= [--instance=] {--state= | --val=} (or) ledtool -s -D [-I ] {-T | -V } Execute repeatedly command by count:= ledtool --iteration=max/ [option1] [option2]... 40 Dell EMC DAIG-OS tools Will take few mins to control the state of this tool.
...FPGA access. Tests To test the LEDs, use the ledtool --test command. ASIC and Phys control the port LEDs and are beyond the scope of the front and back panel light emitting diodes (LEDs). root@dell-diag-os:/opt/dellemc/diag/bin# ./ledtool --test LED Test Started... Led Tool version 1.0, x.xx.x.x-x...specific LED(color and blink):= ledtool --set --led= [--instance=] {--state= | --val=} (or) ledtool -s -D [-I ] {-T | -V } Execute repeatedly command by count:= ledtool --iteration=max/ [option1] [option2]... 40 Dell EMC DAIG-OS tools Will take few mins to control the state of this tool.
Open Networking Hardware Diagnostic Guide December 2021
Page 41
...fast green flashing-green CPLD4-Mode States: normal-mode test-mode Port#37-48-Amber States: off flashing-amber-fast amber flashing-amber Port#37-48-Green States: off flashing-green-fast green flashing-green Output list output root@dell-diag-os:/etc/dn/diag# ledtool --list Power Led :... options green amber flashing-amber off System Led : options amber flashing-green flashing-amber green Fan Led : options green flashing-amber off Beacon LED : options flashing-blue off Ports 1-18 PortLED Mode : ...
...fast green flashing-green CPLD4-Mode States: normal-mode test-mode Port#37-48-Amber States: off flashing-amber-fast amber flashing-amber Port#37-48-Green States: off flashing-green-fast green flashing-green Output list output root@dell-diag-os:/etc/dn/diag# ledtool --list Power Led :... options green amber flashing-amber off System Led : options amber flashing-green flashing-amber green Fan Led : options green flashing-amber off Beacon LED : options flashing-blue off Ports 1-18 PortLED Mode : ...
Open Networking Hardware Diagnostic Guide December 2021
Page 42
... -r, --read Read operation -z, --size= Size 42 Dell EMC DAIG-OS tools Ports 19-36 PortLED Mode : options normal-mode test-mode Ports 19-36 FrontEnd AmberLed : options off flashing-amber-fast amber flashing-amber Ports 19-36 FrontEnd GreenLed : options off flashing-green-fast...Ports 1-18 FrontEnd AmberLed : off Ports 1-18 FrontEnd GreenLed : off Ports 19-36 PortLED Mode : normal-mode Ports 19-36 FrontEnd AmberLed : off Ports 19-36 FrontEnd GreenLed : off Ports 37-48 PortLED Mode : normal-mode Ports 37-48 FrontEnd AmberLed : off Ports 37-48 FrontEnd GreenLed : off root@dell...
... -r, --read Read operation -z, --size= Size 42 Dell EMC DAIG-OS tools Ports 19-36 PortLED Mode : options normal-mode test-mode Ports 19-36 FrontEnd AmberLed : options off flashing-amber-fast amber flashing-amber Ports 19-36 FrontEnd GreenLed : options off flashing-green-fast...Ports 1-18 FrontEnd AmberLed : off Ports 1-18 FrontEnd GreenLed : off Ports 19-36 PortLED Mode : normal-mode Ports 19-36 FrontEnd AmberLed : off Ports 19-36 FrontEnd GreenLed : off Ports 37-48 PortLED Mode : normal-mode Ports 37-48 FrontEnd AmberLed : off Ports 37-48 FrontEnd GreenLed : off root@dell...
Open Networking Hardware Diagnostic Guide December 2021
Page 43
.... -I, --iteration= Iteration command execution -C, --count= Count -a, --addr= Address Output Read output root@dell-diag-os:/opt/dellemc/diag/bin# ./lpctool --read --addr=102 Byte Port 0x102 : 0xde Write output root@dell-diag-os:/opt/dellemc/diag/bin# ./lpctool --write --addr=102 --val=10 memtool The memtool tests ... or opens a memory map to the memory, and passes the pointer to the memtest86 application but focuses on the memory bus. Dell EMC DAIG-OS tools 43 After it completes writing all addressed locations, it walks back through and verifies that the values are available...
.... -I, --iteration= Iteration command execution -C, --count= Count -a, --addr= Address Output Read output root@dell-diag-os:/opt/dellemc/diag/bin# ./lpctool --read --addr=102 Byte Port 0x102 : 0xde Write output root@dell-diag-os:/opt/dellemc/diag/bin# ./lpctool --write --addr=102 --val=10 memtool The memtool tests ... or opens a memory map to the memory, and passes the pointer to the memtest86 application but focuses on the memory bus. Dell EMC DAIG-OS tools 43 After it completes writing all addressed locations, it walks back through and verifies that the values are available...
Open Networking Hardware Diagnostic Guide December 2021
Page 47
...or nputool command. The SDI must ensure the memory accessed is working either using the CPU-generated packet or using IXIA connected to port-1 and port-2 based on test ID := Dump packet counters := Display NPU temperature -l, --lpbk [phy/mac/ext]:= Specify Loopback type for ... Constraints You cannot perform memory tests while other processes. Read output root@dell-diag-os:~# memtool --read --addr=200 [00000200]: 0x00 || . CLI options The nputool shows the available options with other tests that ports are shown in the following sections. NPU Tool version 1.0, x.xx.x.x-x ...
...or nputool command. The SDI must ensure the memory accessed is working either using the CPU-generated packet or using IXIA connected to port-1 and port-2 based on test ID := Dump packet counters := Display NPU temperature -l, --lpbk [phy/mac/ext]:= Specify Loopback type for ... Constraints You cannot perform memory tests while other processes. Read output root@dell-diag-os:~# memtool --read --addr=200 [00000200]: 0x00 || . CLI options The nputool shows the available options with other tests that ports are shown in the following sections. NPU Tool version 1.0, x.xx.x.x-x ...
Open Networking Hardware Diagnostic Guide December 2021
Page 48
version 1.0 sdk-6.5.3 package x.xx.x.x.xx 2016/08/12 root@dell-diag-os:/etc/dn/diag# Port link status test ● nputool -i -t 0 ● nputool --i --test 0 root@dell-diag-os:~# root@dell-diag-os:/etc/dn/diag# nputool -i -t 0 8375_B0 -bash: root@dell-diag-os:/etc/dn/diag#: No such file or directory sysconf_probe ...Test uplink link status ● 5 = Test uplink snake traffic ● 6 = Test uplink prbs mac ● 7 = Test uplink prbs ext nputool version root@dell-diag-os:/etc/dn/diag# nputool --v Dell Diag nputool - SKIPPED version 1.0 sdk-6.5.3 package x.xx.x.x.xx 2016/08/12 root...
version 1.0 sdk-6.5.3 package x.xx.x.x.xx 2016/08/12 root@dell-diag-os:/etc/dn/diag# Port link status test ● nputool -i -t 0 ● nputool --i --test 0 root@dell-diag-os:~# root@dell-diag-os:/etc/dn/diag# nputool -i -t 0 8375_B0 -bash: root@dell-diag-os:/etc/dn/diag#: No such file or directory sysconf_probe ...Test uplink link status ● 5 = Test uplink snake traffic ● 6 = Test uplink prbs mac ● 7 = Test uplink prbs ext nputool version root@dell-diag-os:/etc/dn/diag# nputool --v Dell Diag nputool - SKIPPED version 1.0 sdk-6.5.3 package x.xx.x.x.xx 2016/08/12 root...
Open Networking Hardware Diagnostic Guide December 2021
Page 49
Connect all the ports with QSFP28 Loopback optics. ● nputool -i -t 1 -T cpu_self ● nputool --init --test 1 --traffic cpu_self root@dell-diag-os:/opt/dellemc/diag/bin# nputool -i -t 1 -T cpu_self DMA pool size: 16777216 PCI unit 0: Dev 0x8375, Rev 0x11, Chip BCM88375_B0, Driver BCM88375_B0 sysconf_probe successful global_sal_config ...
Connect all the ports with QSFP28 Loopback optics. ● nputool -i -t 1 -T cpu_self ● nputool --init --test 1 --traffic cpu_self root@dell-diag-os:/opt/dellemc/diag/bin# nputool -i -t 1 -T cpu_self DMA pool size: 16777216 PCI unit 0: Dev 0x8375, Rev 0x11, Chip BCM88375_B0, Driver BCM88375_B0 sysconf_probe successful global_sal_config ...
Open Networking Hardware Diagnostic Guide December 2021
Page 50
Test link_status_test for NPU 0 SKIPPED
Test link_status_test for NPU 0 SKIPPED
Open Networking Hardware Diagnostic Guide December 2021
Page 51
...-t 2 or nputool --init --test 2 ● PRBS EXT level test nputool -i -t 3 or nputool --init --test 3 For example: root@dell-diag-os:~# nputool --init --test 2 DMA pool size: 16777216 PCI unit 0: Dev 0x8375, Rev 0x11, Chip BCM88375_B0, Driver BCM88375_B0 sysconf_probe successful global_sal_config ...successful *** 1 BCM devices are detected Diag NPU initialization over Test link_status_test for QSFP ports Connect ports with Loopback cables and run the show c command in the XP Shell. PRBS for NPU 0 SKIPPED To verify the...
...-t 2 or nputool --init --test 2 ● PRBS EXT level test nputool -i -t 3 or nputool --init --test 3 For example: root@dell-diag-os:~# nputool --init --test 2 DMA pool size: 16777216 PCI unit 0: Dev 0x8375, Rev 0x11, Chip BCM88375_B0, Driver BCM88375_B0 sysconf_probe successful global_sal_config ...successful *** 1 BCM devices are detected Diag NPU initialization over Test link_status_test for QSFP ports Connect ports with Loopback cables and run the show c command in the XP Shell. PRBS for NPU 0 SKIPPED To verify the...
Open Networking Hardware Diagnostic Guide December 2021
Page 54
... show [=brief] [--int=] (or) opticstool -x[=brief] [-I ] Execute repeatedly command by reading the EEPROM. Output show=brief output root@dell-diag-os:~# opticstool --show=brief Show Optics in System (brief) Port # Name Status 1 SFP+ 1 PRESENT 2 SFP+ 2 PRESENT 3 SFP+ 3 PRESENT 4 SFP+ 4 PRESENT 5 SFP+ 5 ...PRESENT 6 SFP+ 6 PRESENT 54 Dell EMC DAIG-OS tools opticstool To check the presence or absence...
... show [=brief] [--int=] (or) opticstool -x[=brief] [-I ] Execute repeatedly command by reading the EEPROM. Output show=brief output root@dell-diag-os:~# opticstool --show=brief Show Optics in System (brief) Port # Name Status 1 SFP+ 1 PRESENT 2 SFP+ 2 PRESENT 3 SFP+ 3 PRESENT 4 SFP+ 4 PRESENT 5 SFP+ 5 ...PRESENT 6 SFP+ 6 PRESENT 54 Dell EMC DAIG-OS tools opticstool To check the presence or absence...
Open Networking Hardware Diagnostic Guide December 2021
Page 56
...QSFP28 1002971051 1 47 QSFP28 47 PRESENT QSFP28 1002971101 1 48 QSFP28 48 PRESENT QSFP28 1002971101 1 root@dell-diag-os:~# CN0C6Y7M48C2MP@ CN0C6Y7M48C2MP@ CN0C6Y7M40A0HB CN0C6Y7M40A0HB CN0C6Y7M41A0BP CN0C6Y7M41A0BP CN0C6Y7M411J CN0C6Y7M411J CN0C6Y7M41A0BR CN0C6Y7M41A0BR CN0C6Y7M40A0HB CN0C6Y7M40A0HB CN0C6Y7M49M4BG5 CN0C6Y7M49M4BG5 ...506220006 506220006 504120586 504120586 show --int=interface # output root@dell-diag-os:~# opticstool --show --int=48 Show Optics in System QSFP28 48 Detailed Display Link Status Port Status Loss of Signal : RX Signal Lock Error : PCS...
...QSFP28 1002971051 1 47 QSFP28 47 PRESENT QSFP28 1002971101 1 48 QSFP28 48 PRESENT QSFP28 1002971101 1 root@dell-diag-os:~# CN0C6Y7M48C2MP@ CN0C6Y7M48C2MP@ CN0C6Y7M40A0HB CN0C6Y7M40A0HB CN0C6Y7M41A0BP CN0C6Y7M41A0BP CN0C6Y7M411J CN0C6Y7M411J CN0C6Y7M41A0BR CN0C6Y7M41A0BR CN0C6Y7M40A0HB CN0C6Y7M40A0HB CN0C6Y7M49M4BG5 CN0C6Y7M49M4BG5 ...506220006 506220006 504120586 504120586 show --int=interface # output root@dell-diag-os:~# opticstool --show --int=48 Show Optics in System QSFP28 48 Detailed Display Link Status Port Status Loss of Signal : RX Signal Lock Error : PCS...
Open Networking Hardware Diagnostic Guide December 2021
Page 61
... address of the interface:= phytool --read-mac phytool -R Write the value to the specified offset:= phytool --write --offset= --val= (or) (or) (or) Dell EMC DAIG-OS tools 61 Base Address 2: Memory at 0x88, next 144. Extended PCI capability type 1 at 0x0001fff0. root...@dell-diag-os:/etc/dn/diag# phytool The phytool allows setting the management phy for management port for speed, duplex auto negotiation, and Loopback; Base Address 5: I/O at 0x80, next 136. Power state ...
... address of the interface:= phytool --read-mac phytool -R Write the value to the specified offset:= phytool --write --offset= --val= (or) (or) (or) Dell EMC DAIG-OS tools 61 Base Address 2: Memory at 0x88, next 144. Extended PCI capability type 1 at 0x0001fff0. root...@dell-diag-os:/etc/dn/diag# phytool The phytool allows setting the management phy for management port for speed, duplex auto negotiation, and Loopback; Base Address 5: I/O at 0x80, next 136. Power state ...
Open Networking Hardware Diagnostic Guide December 2021
Page 63
... Tool version x.x, x.xx.x.x-x build, yyyy/mm/dd, Dell EMC DAIG-OS tools 63 You need to reboot to ... read and write registers in the device. speed 1000 Mbps - The pltool also checks for eth0: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supported pause frame...Full 100baseT/Half 100baseT/Full 1000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Speed: 1000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 3 Transceiver: internal Auto-negotiation: on MDI-X: off (auto) Supports Wake-on: pumbg Wake-on...
... Tool version x.x, x.xx.x.x-x build, yyyy/mm/dd, Dell EMC DAIG-OS tools 63 You need to reboot to ... read and write registers in the device. speed 1000 Mbps - The pltool also checks for eth0: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supported pause frame...Full 100baseT/Half 100baseT/Full 1000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Speed: 1000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 3 Transceiver: internal Auto-negotiation: on MDI-X: off (auto) Supports Wake-on: pumbg Wake-on...