Information Update
Page 4
Each channel supports up to the IDE system board connectors. Table 1-1 lists guidelines for installing IDE drives connected to two IDE devices. Figure 1-2 shows the location of these connectors on the system board. 1-2 Information Update www.dell.com | support.dell.com Figure 1-1. Removing and Replacing the Microprocessor Heat Sink thermal grease protective cover-remove before installing heat sink cooling fan heat sink microprocessor IDE Drive Configurations The IDE subsystem provides three channels (primary, secondary, and tertiary).
Each channel supports up to the IDE system board connectors. Table 1-1 lists guidelines for installing IDE drives connected to two IDE devices. Figure 1-2 shows the location of these connectors on the system board. 1-2 Information Update www.dell.com | support.dell.com Figure 1-1. Removing and Replacing the Microprocessor Heat Sink thermal grease protective cover-remove before installing heat sink cooling fan heat sink microprocessor IDE Drive Configurations The IDE subsystem provides three channels (primary, secondary, and tertiary).
Microprocessor Upgrade Installation Guide
Page 3
... items are included in the microprocessor upgrade kit: • A microprocessor • A heat sink with cooling fan CAUTION: See your System Information Guide for replacing a microprocessor. NOTICE: The microprocessor fan and heat sink are contained in a pin-grid array (PGA) package that is installed in your system...can overheat if the thermal interface is required to remove the fan from the front of future options in your Installation and Troubleshooting Guide). 3 Lay the system on the Dell Support website at support.dell.com, and upgrade the BIOS if necessary. Do not attempt ...
... items are included in the microprocessor upgrade kit: • A microprocessor • A heat sink with cooling fan CAUTION: See your System Information Guide for replacing a microprocessor. NOTICE: The microprocessor fan and heat sink are contained in a pin-grid array (PGA) package that is installed in your system...can overheat if the thermal interface is required to remove the fan from the front of future options in your Installation and Troubleshooting Guide). 3 Lay the system on the Dell Support website at support.dell.com, and upgrade the BIOS if necessary. Do not attempt ...
Microprocessor Upgrade Installation Guide
Page 4
... tabs on the system board. Removing and Replacing the Microprocessor Heat Sink thermal grease tab - www.dell.com | support.dell.com 4 Remove the heat sink from the existing microprocessor (see Figure 1-1): a Disconnect the cooling fan cable from the fan connector on the ZIF socket. b Press down on the heat-sink securing clips to the fully...
... tabs on the system board. Removing and Replacing the Microprocessor Heat Sink thermal grease tab - www.dell.com | support.dell.com 4 Remove the heat sink from the existing microprocessor (see Figure 1-1): a Disconnect the cooling fan cable from the fan connector on the ZIF socket. b Press down on the heat-sink securing clips to the fully...
Microprocessor Upgrade Installation Guide
Page 6
NOTICE: The cooling fan must be sure that all of the new microprocessor and automatically ... on the microprocessor, place the heat sink upside down on a flat surface to the closed position. www.dell.com | support.dell.com NOTICE: Positioning the microprocessor incorrectly can overheat if the thermal interface is fully seated in the socket (...placing the microprocessor in the socket, be connected for the microprocessor to maintain proper thermal conditions. 14 Connect the fan cable to expose the thermal grease, and then place the heat sink on the microprocessor. • If the ...
NOTICE: The cooling fan must be sure that all of the new microprocessor and automatically ... on the microprocessor, place the heat sink upside down on a flat surface to the closed position. www.dell.com | support.dell.com NOTICE: Positioning the microprocessor incorrectly can overheat if the thermal interface is fully seated in the socket (...placing the microprocessor in the socket, be connected for the microprocessor to maintain proper thermal conditions. 14 Connect the fan cable to expose the thermal grease, and then place the heat sink on the microprocessor. • If the ...