CLI Guide
Page 12
... This example shows how to login... 16 2000-01-22 01:20:37 INFO(6) Logout through Console (Username: admin) DXS-3600-32S TenGigabit Ethernet Switch Command Line Interface Firmware: Build 1.10.023 Copyright(C) 2012 D-Link Corporation. If the current session is another session running, it will logout. Switch con0 is used to exit any...
... This example shows how to login... 16 2000-01-22 01:20:37 INFO(6) Logout through Console (Username: admin) DXS-3600-32S TenGigabit Ethernet Switch Command Line Interface Firmware: Build 1.10.023 Copyright(C) 2012 D-Link Corporation. If the current session is another session running, it will logout. Switch con0 is used to exit any...
CLI Guide
Page 48
...minutes Enter the timeout value used to add a permanent IP address and MAC address mapping to the MAC address here. Enter the 48-bit data link layer address here. Example This example shows how to remove the IP-MAC address mapping. arp [vrf ] ip-address mac-address no ' ...the old one, the new entry will be replaced by entering the show ip arp or show arp command. DXS-3600-32S#configure terminal DXS-3600-32S(config)#arp 33.1.1.33 0050.BA00.0736 DXS-3600-32S(config)# Example This example shows how to configure the timeout value for the dynamic ARP mapping record in the ARP...
...minutes Enter the timeout value used to add a permanent IP address and MAC address mapping to the MAC address here. Enter the 48-bit data link layer address here. Example This example shows how to remove the IP-MAC address mapping. arp [vrf ] ip-address mac-address no ' ...the old one, the new entry will be replaced by entering the show ip arp or show arp command. DXS-3600-32S#configure terminal DXS-3600-32S(config)#arp 33.1.1.33 0050.BA00.0736 DXS-3600-32S(config)# Example This example shows how to configure the timeout value for the dynamic ARP mapping record in the ARP...
CLI Guide
Page 75
... physical interface because the loopback interface is to configure a loopback interface, since the physical interface link may be aggregated if the BGP aggregate next hop check is disabled. DXS-3600 Series 10GbE Layer 2/3 Switch CLI Reference Guide 7-4 bgp router-id This command is used ..../down . Example This example shows how to change the router ID to 192.168.1.1 DXS-3600-32S#configure terminal DXS-3600-32S(config)#router bgp 65100 DXS-3600-32S(config-router)#bgp router-id 192.168.1.1 DXS-3600-32S(config-router)# 7-5 bgp aggregate-next-hop-check This command is used to an IP ...
... physical interface because the loopback interface is to configure a loopback interface, since the physical interface link may be aggregated if the BGP aggregate next hop check is disabled. DXS-3600 Series 10GbE Layer 2/3 Switch CLI Reference Guide 7-4 bgp router-id This command is used ..../down . Example This example shows how to change the router ID to 192.168.1.1 DXS-3600-32S#configure terminal DXS-3600-32S(config)#router bgp 65100 DXS-3600-32S(config-router)#bgp router-id 192.168.1.1 DXS-3600-32S(config-router)# 7-5 bgp aggregate-next-hop-check This command is used to an IP ...
CLI Guide
Page 86
... the link used to initiate an inbound reconfiguration. Specifies that the first AS number in nor the out keywords are supported. DXS-3600 Series 10GbE Layer 2/3 Switch CLI Reference Guide Example This example shows how to reset the peering session. DXS-3600-32S#configure terminal DXS-3600-32S(config)#router bgp 65534 DXS-3600-32S(config-router)#bgp enforce-first-as DXS-3600-32S(config...
... the link used to initiate an inbound reconfiguration. Specifies that the first AS number in nor the out keywords are supported. DXS-3600 Series 10GbE Layer 2/3 Switch CLI Reference Guide Example This example shows how to reset the peering session. DXS-3600-32S#configure terminal DXS-3600-32S(config)#router bgp 65534 DXS-3600-32S(config-router)#bgp enforce-first-as DXS-3600-32S(config...
CLI Guide
Page 160
The maximum length is 12 characters. DXS-3600-32S#show ip bgp peer-group [{[vrf VRF-NAME] [PEER-GROUP-NAME] | ...enabled. 7-88 show ip bgp peer-group This command is used to reach these peers goes down. DXS-3600 Series 10GbE Layer 2/3 Switch CLI Reference Guide Display Parameters Fast External Fallover Aggregate Next Hop Check Description If... enable, Border Gateway Protocol (BGP) routing process will immediately reset its external BGP peer sessions if the link used to display information of a Border Gateway Protocol (BGP) peer group. show ip bgp peer-group mygroup ...
The maximum length is 12 characters. DXS-3600-32S#show ip bgp peer-group [{[vrf VRF-NAME] [PEER-GROUP-NAME] | ...enabled. 7-88 show ip bgp peer-group This command is used to reach these peers goes down. DXS-3600 Series 10GbE Layer 2/3 Switch CLI Reference Guide Display Parameters Fast External Fallover Aggregate Next Hop Check Description If... enable, Border Gateway Protocol (BGP) routing process will immediately reset its external BGP peer sessions if the link used to display information of a Border Gateway Protocol (BGP) peer group. show ip bgp peer-group mygroup ...
CLI Guide
Page 177
... show interface Interface Information: Name Index Network ------ Example This example shows how to show internal detailed information about the BGP interface. None. DXS-3600-32S#debug ip bgp show timer BGP timer Link: Node Time ---- ---- 08B108D0 1 08B1AC70 16 08B1ACA8 17 08B37DCC 29 08B37E04 30 032821BC 35 08B1AC54 135 08B37DB0 148 Func -----00675AF4 0065F4F4 0065F5CC...
... show interface Interface Information: Name Index Network ------ Example This example shows how to show internal detailed information about the BGP interface. None. DXS-3600-32S#debug ip bgp show timer BGP timer Link: Node Time ---- ---- 08B108D0 1 08B1AC70 16 08B1ACA8 17 08B37DCC 29 08B37E04 30 032821BC 35 08B1AC54 135 08B37DB0 148 Func -----00675AF4 0065F4F4 0065F5CC...
CLI Guide
Page 183
.... Example This example shows how the configuration information of the current device's configuration system running -config Building configuration... DXS-3600-32S#show running . The boot-up configuration can be changed by boot config command in global configuration mode. 175 None...stored in the Non-volatile Random Access Memory (NVRAM). Current configuration : 108272 bytes # DXS-3600-32S TenGigabit Ethernet Switch # Configuration # # Firmware: Build 1.10.023 # Copyright(C) 2012 D-Link Corporation. None. Privileged Mode. Level: 15 This command is used to show the ...
.... Example This example shows how the configuration information of the current device's configuration system running -config Building configuration... DXS-3600-32S#show running . The boot-up configuration can be changed by boot config command in global configuration mode. 175 None...stored in the Non-volatile Random Access Memory (NVRAM). Current configuration : 108272 bytes # DXS-3600-32S TenGigabit Ethernet Switch # Configuration # # Firmware: Build 1.10.023 # Copyright(C) 2012 D-Link Corporation. None. Privileged Mode. Level: 15 This command is used to show the ...
CLI Guide
Page 184
DXS-3600-32S#show running-config command. All rights reserved. # DEVICE configure terminal logging-server enable device end # PRIVMGMT configure terminal # COMMAND LEVEL START # COMMAND LEVEL END.... This means that CLI commands are self-explanatory. To verify the executed result, use the show bootup-config # DXS-3600-32S TenGigabit Ethernet Switch # Configuration # # Firmware: Build 1.10.023 # Copyright(C) 2012 D-Link Corporation. Hence, it is necessary to execute the configuration by using the increment method. Default Command Mode Command Default ...
DXS-3600-32S#show running-config command. All rights reserved. # DEVICE configure terminal logging-server enable device end # PRIVMGMT configure terminal # COMMAND LEVEL START # COMMAND LEVEL END.... This means that CLI commands are self-explanatory. To verify the executed result, use the show bootup-config # DXS-3600-32S TenGigabit Ethernet Switch # Configuration # # Firmware: Build 1.10.023 # Copyright(C) 2012 D-Link Corporation. Hence, it is necessary to execute the configuration by using the increment method. Default Command Mode Command Default ...
CLI Guide
Page 205
... through TFTP to a file named 'tech-info.txt' at 10.0.0.90 DXS-3600-32S#configure terminal DXS-3600-32S(config)#copy tech-support tftp //10.0.0.90/tech_info.txt DXS-3600-32S(config)# 197 Specifies the location of the upload technical support information. All ... to a location filename through a TFTP server. DXS-3600 Series 10GbE Layer 2/3 Switch CLI Reference Guide Example This example shows how to show tech-support # DXS-3600-32S TenGigabit Ethernet Switch # Technical Support Information # # Firmware: Build 1.10.023 # Copyright(C) 2012 D-Link Corporation.
... through TFTP to a file named 'tech-info.txt' at 10.0.0.90 DXS-3600-32S#configure terminal DXS-3600-32S(config)#copy tech-support tftp //10.0.0.90/tech_info.txt DXS-3600-32S(config)# 197 Specifies the location of the upload technical support information. All ... to a location filename through a TFTP server. DXS-3600 Series 10GbE Layer 2/3 Switch CLI Reference Guide Example This example shows how to show tech-support # DXS-3600-32S TenGigabit Ethernet Switch # Technical Support Information # # Firmware: Build 1.10.023 # Copyright(C) 2012 D-Link Corporation.
CLI Guide
Page 233
... None. DXS-3600 Series 10GbE Layer 2/3 Switch CLI Reference Guide D-Link License Management System Commands 16-1 install dlms activation_code This command is used to display the license information on the switch. Privileged Mode. Level: 15 This command is used to active the license. Please reboot the device to install an activation code. DXS-3600-32S#install...
... None. DXS-3600 Series 10GbE Layer 2/3 Switch CLI Reference Guide D-Link License Management System Commands 16-1 install dlms activation_code This command is used to display the license information on the switch. Privileged Mode. Level: 15 This command is used to active the license. Please reboot the device to install an activation code. DXS-3600-32S#install...
CLI Guide
Page 260
...link aggregation groups. The GVRP function cannot be enabled when the interface is operating in access mode or Dot1Q-tunnel mode, meaning that a VLAN should be advertised. DXS-3600-32S#configure terminal DXS-3600-32S(config)#interface tenGigabitEthernet 1/0/1 DXS-3600-32S(config-if)#gvrp advertise 1-1000 DXS-3600-32S... This example shows how to enable/disable the GVRP protocol state. DXS-3600-32S#configure terminal DXS-3600-32S(config)#interface tenGigabitEthernet 1/0/1 DXS-3600-32S(config-if)#gvrp DXS-3600-32S(config-if)# 22-4 gvrp advertise (Interface) This command is not...
...link aggregation groups. The GVRP function cannot be enabled when the interface is operating in access mode or Dot1Q-tunnel mode, meaning that a VLAN should be advertised. DXS-3600-32S#configure terminal DXS-3600-32S(config)#interface tenGigabitEthernet 1/0/1 DXS-3600-32S(config-if)#gvrp advertise 1-1000 DXS-3600-32S... This example shows how to enable/disable the GVRP protocol state. DXS-3600-32S#configure terminal DXS-3600-32S(config)#interface tenGigabitEthernet 1/0/1 DXS-3600-32S(config-if)#gvrp DXS-3600-32S(config-if)# 22-4 gvrp advertise (Interface) This command is not...
CLI Guide
Page 261
... VLAN does not exist, the VLAN will be created automatically. DXS-3600-32S#configure terminal DXS-3600-32S(config)#gvrp DXS-3600-32S(config)#gvrp dynamic-vlan-creation DXS-3600-32S(config)# 22-6 forbidden vlan This command is used . Default ...Command Mode Command Default Level Usage Guideline None. Otherwise, the newly learned VLAN will lead to specify a port as its forbidden VLAN will not be configured on physical ports or link...
... VLAN does not exist, the VLAN will be created automatically. DXS-3600-32S#configure terminal DXS-3600-32S(config)#gvrp DXS-3600-32S(config)#gvrp dynamic-vlan-creation DXS-3600-32S(config)# 22-6 forbidden vlan This command is used . Default ...Command Mode Command Default Level Usage Guideline None. Otherwise, the newly learned VLAN will lead to specify a port as its forbidden VLAN will not be configured on physical ports or link...
CLI Guide
Page 330
... 1/0/1 detail Interface ID : 1/0/1 Port ID Subtype : MAC Address Port ID : 00-01-02-03-05-00 Port Description : D-Link DXS-3600-32S R1.10.023 P ort 1 on Unit 1 Port PVID : 1 Management Address Count : 1 PPVID Entries Count : 0 VLAN Name...PHY Configuration/Status : (See Detail) Link Aggregation : (See Detail) Maximum Frame Size : 1536 DXS-3600-32S# 322 DXS-3600-32S#show lldp local interface tenGigabitEthernet 1/0/1 normal Interface ID : 1/0/1 Port ID Subtype : MAC Address Port ID : 00-01-02-03-05-00 Port Description : D-Link DXS-3600-32S R1.10.023 P ort 1 ...
... 1/0/1 detail Interface ID : 1/0/1 Port ID Subtype : MAC Address Port ID : 00-01-02-03-05-00 Port Description : D-Link DXS-3600-32S R1.10.023 P ort 1 on Unit 1 Port PVID : 1 Management Address Count : 1 PPVID Entries Count : 0 VLAN Name...PHY Configuration/Status : (See Detail) Link Aggregation : (See Detail) Maximum Frame Size : 1536 DXS-3600-32S# 322 DXS-3600-32S#show lldp local interface tenGigabitEthernet 1/0/1 normal Interface ID : 1/0/1 Port ID Subtype : MAC Address Port ID : 00-01-02-03-05-00 Port Description : D-Link DXS-3600-32S R1.10.023 P ort 1 ...
CLI Guide
Page 331
... Interface ID : 1/0/1 Port ID Subtype : MAC Address Port ID : 00-01-02-03-05-00 Port Description : D-Link DXS-3600-32S R1.10.023 P ort 1 on Unit 1 DXS-3600-32S# 32-19 show lldp remote interface interface-id [, | -] {brief | normal | detail} Parameters interface interface-id , brief normal... the comma. (Optional) Specifies a range of interfaces from the neighbor parameters. 323 Displays the information in brief mode. DXS-3600 Series 10GbE Layer 2/3 Switch CLI Reference Guide Example This example shows how to display the each physical interface information currently learned...
... Interface ID : 1/0/1 Port ID Subtype : MAC Address Port ID : 00-01-02-03-05-00 Port Description : D-Link DXS-3600-32S R1.10.023 P ort 1 on Unit 1 DXS-3600-32S# 32-19 show lldp remote interface interface-id [, | -] {brief | normal | detail} Parameters interface interface-id , brief normal... the comma. (Optional) Specifies a range of interfaces from the neighbor parameters. 323 Displays the information in brief mode. DXS-3600 Series 10GbE Layer 2/3 Switch CLI Reference Guide Example This example shows how to display the each physical interface information currently learned...
CLI Guide
Page 332
...detail Remote Entities Count : 1 Interface ID : 1/0/1 Port ID Subtype : MAC Address Port ID : 00-02-03-04-05-06 Port Description : D-Link DXS-3600-32S R1.10.023 P ort 1 on Unit 1 Port PVID : 1 Management Address Count : 1 PPVID Entries Count : 0 VLAN Name Entries Count : ... normal Remote Entities Count : 1 Interface ID : 1/0/1 Port ID Subtype : MAC Address Port ID : 00-02-03-04-05-06 Port Description : D-Link DXS-3600-32S R1.10.023 P ort 1 on Unit 1 Port PVID : 1 Management Address Count : 1 Subtype : IPv4 Address : 0.0.0.0 IF Type : IfIndex OID...
...detail Remote Entities Count : 1 Interface ID : 1/0/1 Port ID Subtype : MAC Address Port ID : 00-02-03-04-05-06 Port Description : D-Link DXS-3600-32S R1.10.023 P ort 1 on Unit 1 Port PVID : 1 Management Address Count : 1 PPVID Entries Count : 0 VLAN Name Entries Count : ... normal Remote Entities Count : 1 Interface ID : 1/0/1 Port ID Subtype : MAC Address Port ID : 00-02-03-04-05-06 Port Description : D-Link DXS-3600-32S R1.10.023 P ort 1 on Unit 1 Port PVID : 1 Management Address Count : 1 Subtype : IPv4 Address : 0.0.0.0 IF Type : IfIndex OID...
CLI Guide
Page 333
...and after the hyphen. No space before and after the comma. (Optional) Specifies a range of Table Ageout : 0 DXS-3600-32S# 32-21 show lldp statistic This command is used to display each physical interface LLDP statistics information. Default Command Mode None. ...Command Mode Command Default Level Usage Guideline None. DXS-3600-32S#show lldp remote interface tenGigabitEthernet 1/0/1 brief Remote Entities Count : 1 Interface ID : 1/0/1 Port ID Subtype : MAC Address Port ID : 00-02-03-04-05-06 Port Description : D-Link DXS-3600-32S R1.10.023 P ort 1 on the ...
...and after the hyphen. No space before and after the comma. (Optional) Specifies a range of Table Ageout : 0 DXS-3600-32S# 32-21 show lldp statistic This command is used to display each physical interface LLDP statistics information. Default Command Mode None. ...Command Mode Command Default Level Usage Guideline None. DXS-3600-32S#show lldp remote interface tenGigabitEthernet 1/0/1 brief Remote Entities Count : 1 Interface ID : 1/0/1 Port ID Subtype : MAC Address Port ID : 00-02-03-04-05-06 Port Description : D-Link DXS-3600-32S R1.10.023 P ort 1 on the ...
CLI Guide
Page 342
... Revision Serial Number Manufacturer Name Model Name Asset ID : Network Connectivity Device : : 1.10.007 : 1.10.023 : D1234567890 : D-Link : DXS-3600-32S TenGigabit Ethernet : LLDP-MED Configuration: Fast Start Repeat Count : 10 LLDP-MED Log State:Disabled DXS-3600-32S# 34-5 show lldp-med interface This command is used to display a specific physical interface configuration. No space before...
... Revision Serial Number Manufacturer Name Model Name Asset ID : Network Connectivity Device : : 1.10.007 : 1.10.023 : D1234567890 : D-Link : DXS-3600-32S TenGigabit Ethernet : LLDP-MED Configuration: Fast Start Repeat Count : 10 LLDP-MED Log State:Disabled DXS-3600-32S# 34-5 show lldp-med interface This command is used to display a specific physical interface configuration. No space before...
CLI Guide
Page 413
... OSPF VRF instance. Privileged EXEC Mode. The times that neighbor state has changed. 40-29 show ip ospf virtual-link This command is specified, only the virtual link with IP 10.1.1.2. DXS-3600-32S#show virtual link information. Level: 3. (EI Mode Only Command) Use this command to show ip ospf neighbor 2.2.2.2 Neighbor ID: 2.2.2.2 Neighbor Options: 2 Neighbor...
... OSPF VRF instance. Privileged EXEC Mode. The times that neighbor state has changed. 40-29 show ip ospf virtual-link This command is specified, only the virtual link with IP 10.1.1.2. DXS-3600-32S#show virtual link information. Level: 3. (EI Mode Only Command) Use this command to show ip ospf neighbor 2.2.2.2 Neighbor ID: 2.2.2.2 Neighbor Options: 2 Neighbor...
CLI Guide
Page 419
... EXEC Mode. Level: 15. (EI Mode Only Command) Use this command to turn on or turn off OSPF timer debug switch. DXS-3600-32S#debug ip ospf virtual-link DXS-3600-32S# Virtual link up transit area 1.1.1.1 vnbr 3.3.3.3 tic 260 40-41 debug ip ospf route This command is turned off. debug ip ospf route no... is used to turn on the OSPF route debug switch. Example This example shows how to OSPF virtual link happens, the debug information will be print. DXS-3600-32S#debug ip ospf timer DXS-3600-32S# Start Hello timer at interface 10.90.90.90 tic 20 Wait timer expired at interface 10.90...
... EXEC Mode. Level: 15. (EI Mode Only Command) Use this command to turn on or turn off OSPF timer debug switch. DXS-3600-32S#debug ip ospf virtual-link DXS-3600-32S# Virtual link up transit area 1.1.1.1 vnbr 3.3.3.3 tic 260 40-41 debug ip ospf route This command is turned off. debug ip ospf route no... is used to turn on the OSPF route debug switch. Example This example shows how to OSPF virtual link happens, the debug information will be print. DXS-3600-32S#debug ip ospf timer DXS-3600-32S# Start Hello timer at interface 10.90.90.90 tic 20 Wait timer expired at interface 10.90...
CLI Guide
Page 672
... can help network administrators reach this feature is only applicable when there is necessary and important. Power on the D-Link DXS-3600-32S switch. This includes resetting the user accounts to physically access the device. Password Recovery Procedure This section describes the procedure...Password Recovery Mode" only the following steps explain how to use the Password Recovery feature on this switch to the factory default settings. DXS-3600 Series 10GbE Layer 2/3 Switch CLI Reference Guide Appendix A - Authenticating any user who tries to access networks is a direct connection to...
... can help network administrators reach this feature is only applicable when there is necessary and important. Power on the D-Link DXS-3600-32S switch. This includes resetting the user accounts to physically access the device. Password Recovery Procedure This section describes the procedure...Password Recovery Mode" only the following steps explain how to use the Password Recovery feature on this switch to the factory default settings. DXS-3600 Series 10GbE Layer 2/3 Switch CLI Reference Guide Appendix A - Authenticating any user who tries to access networks is a direct connection to...