Cisco 2950 24 - Catalyst Switch Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco 2950 24 manuals!
Problems with Cisco 2950 24?
Ask a Question
Free Cisco 2950 24 manuals!
Problems with Cisco 2950 24?
Ask a Question
Popular Cisco 2950 24 Manual Pages
Configuration Guide - Page 19
... this manual.
78-11380-03
Catalyst 2950 Desktop Switch Software Configuration Guide
xix It describes how to apply ACLs to the IOS software. The online help provides the CMS procedures. Conventions
This guide uses these conventions to certain types of service (QoS). Chapter 13, "Configuring QoS," provides the considerations and CLI procedures for configuring the switch ports. The...
Configuration Guide - Page 85
...-11380-03
Catalyst 2950 Desktop Switch Software Configuration Guide
4-3
You might want to write down the port number to privileged EXEC mode so that allows switch management from a standard web browser.
The default data characteristics of communication with the switch through which includes assigning a privilege-level 15 password for accessing
CMS • Installing the required...
Configuration Guide - Page 97
...of another cluster.
78-11380-03
Catalyst 2950 Desktop Switch Software Configuration Guide
5-3 Note • When the command switch is a Catalyst 3550 switch, all standby command switches must be Catalyst 3550 switches or Catalyst 2950 switches running Cisco IOS Release 12.1(6)EA2 or later.
• When the command switch is a Catalyst 2950 switch running Cisco IOS Release 12.1(6)EA2 or later...
Configuration Guide - Page 104
... HSRP priority values, refer to the standby priority interface configuration mode command in the Cisco IOS Release 12.1 documentation set on page 5-11. A cluster standby group is a Catalyst 2950 switch running Cisco IOS Release 12.1(6)EA2 or later, all the member switches, we strongly recommend that meet the requirements described in the group is 10 seconds...
Configuration Guide - Page 106
... Different Management VLANs" section on page 5-7
5-12
Catalyst 2950 Desktop Switch Software Configuration Guide
78-11380-03 Each standby-group member must also be Catalyst 2950 switches running Cisco IOS Release 12.1(6)EA2 or later, all standby command switches must be of the same platform family as standby command switches. For more than 16.
• The active command...
Configuration Guide - Page 114
...have set on page 5-10. Note The HSRP standby hold time and hello time intervals, refer to the Cisco IOS Release 12.1 documentation set by using CMS to add switches to ...in the "Standby Command Switch Characteristics" section on page 5-3 and "HSRP and Standby Command Switches" section on Cisco.com.
5-20
Catalyst 2950 Desktop Switch Software Configuration Guide
78-11380-03 The ...
Configuration Guide - Page 140
...+ Server Host" section on TACACS+ accounting for each Cisco IOS privilege level and for authenticated users who login through the CLI even if authorization has been configured. To specify that is used if no list is bypassed for network services.
6-22
Catalyst 2950 Desktop Switch Software Configuration Guide
78-11380-03 Beginning in privileged EXEC mode...
Configuration Guide - Page 177
... be in your network. The switch then ignores advertisements with a different domain name or an earlier configuration revision number. If you must decide whether to use VTP in only one switch or several problems, such as a Catalyst 2950 switch, and have those changes automatically communicated to the management VLAN, VLAN 1. For domain name and password configuration guidelines...
Configuration Guide - Page 181
... change the VTP mode to an existing network with VTP capability, the new switch learns the domain name only after the applicable password has been configured on the version 2-capable switch.
Upgrading from Previous Software Releases
When you upgrade from a software version that supports VLANs but does not support VTP, such as a switch running VTP version 1 if version 2 is booted...
Configuration Guide - Page 269
...2950 Desktop Switch Software Configuration Guide
11-3 CLI: Enabling IGMP Immediate-Leave Processing
When you enable IGMP Immediate-Leave processing, the switch immediately removes a port... switch to the Cisco IOS Release 12.1 documentation on Cisco.com for all hosts on a switched network... table without first sending out group-specific queries to the Cisco IOS Release 12.1 documentation on a...
Configuration Guide - Page 292
... cost bit. For more details on the minimize-monetary-cost type of service (TOS) bit. You cannot reorder the list or selectively add or remove ACEs from a numbered list.
12-10
Catalyst 2950 Desktop Switch Software Configuration Guide
78-11380-03 Configuring ACLs
Chapter 12 Configuring Network Security with ACLs
1. No support for the filtering parameter. 2.
Configuration Guide - Page 343
...:
Switch# no output appears, consider these periods decreases the likelihood that increased debug command processing overhead will affect system use debug commands only to troubleshoot specific problems or...transfer. To disable debugging of the command:
Switch# undebug etherchannel
78-11380-03
Catalyst 2950 Desktop Switch Software Configuration Guide
14-11 Use the boot loader to monitor...
Configuration Guide - Page 346
... to add another ACL in separate error messages that an attempt was made to be supported Policers required exceed Maximum Allowed on Gigabit Ethernet port.
Catalyst 2950 Desktop Switch Software Configuration Guide
A-2
78-11380-03
The exact cause is provided in the class map.
%Error:the ACL has a different mask than permitted.
%Error:Service policy can not exist together...
Configuration Guide - Page 347
...one QoS mask is allowed. You have to program the hardware.
%Error:Invalid ingress port
This error message means that the hardware had a problem programming the resource. This is an error message that is preceded by a more than one QoS mask on ...precede a Layer 3 (IP
allowed after TCP/UDP protocol ACE
protocol) ACE.
78-11380-03
Catalyst 2950 Desktop Switch Software Configuration Guide
A-3
Configuration Guide - Page 370
... network environments 6-24 tracking services accessed by user 6-34
rcommand command 5-23 read-only access mode 2-31
IN-16
Catalyst 2950 Desktop Switch Software Configuration Guide
read-write access mode 2-31 reconfirmation interval, changing 8-33 recovery procedures 14-5 redundancy
EtherChannel 10-8 STP
backbone 9-8 multidrop backbone 9-12 path cost 8-27 port priority 8-25 redundant clusters...
Cisco 2950 24 Reviews
We have not received any reviews for Cisco yet.