Campbell Scientific CS725 Support and Manuals

Get Help and Manuals for this Campbell Scientific item

View All Support Options Below
Free Campbell Scientific CS725 manuals!
Problems with Campbell Scientific CS725?

Ask a Question

Popular Campbell Scientific CS725 Manual Pages

CS725 Snow Water Equivalency Sensor - Page 1

CS725 Snow Water Equivalency Sensor Revision: 8/12 Copyright © 2010-2012 Campbell Scientific, Inc.
CS725 Snow Water Equivalency Sensor - Page 3

... in materials and workmanship under normal use and service for installation services performed by Campbell such as programming to customer specifications, electrical connections to any special, indirect, incidental, and/or consequential damages." To all other consumables have been subjected to repairing or replacing (at Campbell's option) defective products, which have no warranty...
CS725 Snow Water Equivalency Sensor - Page 4

... unable to refuse service on the outside of the shipping container. Campbell Scientific reserves the right to process any returns until we receive this number clearly on products that were exposed to (435) 227-9106. Affiliate companies handle repairs for our employees. After an applications engineer determines the nature of the problem, an RMA number...
CS725 Snow Water Equivalency Sensor - Page 11

...: Parity: Stop Bits: Flow Control: Local Echo: Terminal Mode: Send Line Ends with the CS725. CS725 connection to DB9F-TERM When connecting the CS725 to a computer, a power source is recommended to power the CS725. After the connections are the settings required for RS-232 Communications The following are verified, the connector can be used such...
CS725 Snow Water Equivalency Sensor - Page 12

...CS725 does support an Auto Baud Rate Detection feature. and a carriage return. This will trigger the auto-baud system, and the CS725 will adjust its baud rate to the CS725...entered into the CS725. Communicating with the ESC character to leave the setting at 9600 bps... as CS725) Is the Gamma Detector Type Is the Firmware Software Revision Is the sensor's serial number 6. CS725 Snow ...
CS725 Snow Water Equivalency Sensor - Page 13

...used to set the language setting to file function [.0xpr] Parameters recovery from file function [%Rhard]/[%Rboot] Restart software processor/reboot firmware [UU] CS725/terminal synchronizing...manual measurement (histogram, position and #counts K and TI). [.e] Same as command , but erases histogram at end of either French or English. To change the language setting, key the command .L. CS725...
CS725 Snow Water Equivalency Sensor - Page 16

...seconds. The CS725 is used to specify the delay and duration in the manual mode by entering the Parameter menu [.p] and set parameter 19 to 1 for manual mode. If the CS725 is placed in the manual mode. This...:20 The CS725 does not perform any time zone or daylight-savings time correction. This can then be setup in the process to display the current date and time. CS725 Snow Water ...
CS725 Snow Water Equivalency Sensor - Page 20

...Setup menu. ex: Gouin_21) :CS725_#1 [3] Time of start of measure (relative to GMON 00h RTC) : 00 [4] Delay after start of measurements will end. HCalib mode (2); : 1 [0] Quit without saving the new parameters on EPROM [99] Save parameters on the histogram : 245 [8] Collim (1: Collimator installed...CS725 Snow Water Equivalency Sensor 14. [.fs] The [.fs] command is used to the time set...
CS725 Snow Water Equivalency Sensor - Page 22

... potassium 40K isotope peak, with manual measurements. It represents the integrated ...of the soil at the installation site. The format is a site-specific parameter used in order .... [10] Estimated soil humidity in the calculation of the CS725. The value is a tool to account for the thallium ... completed and Campbell Scientific has been consulted. [13] N0Tl This site-specific parameter is ...
CS725 Snow Water Equivalency Sensor - Page 23

...mm), the absorption of the gamma rays is set, the CS725 will acquire the data in the parameter description ... and the CS725 calculates the humidity of the soil. The default rate is recommended to contact Campbell Scientific technical support prior to a... mode with a different baud rate. In the manual mode (code =1), the CS725 will be used for the communication device. Valid values...
CS725 Snow Water Equivalency Sensor - Page 25

... of the CS725 to the terminal baud rate. 6.5 Hidden Commands Two commands are intentionally hidden from the CS725 due to upload new firmware into the CS725. You will... use of its weight. Parts Overview The following diagram shows a standard CS725 and some of them. Do not use Campbell Scientific dataloggers such as change settings or update the CS725 clock. 7. Once executed,...
CS725 Snow Water Equivalency Sensor - Page 28

... the measurement (seconds) (Delay should be required to improve the results from the CS725. Once the site is installed on the CS725. • Connect the CS725 to the laptop computer and power supply as shown in Section 10, Final Parameter Setup. • The CS725 will send out a prompt as reasonable to its desired permanent location. •...
CS725 Snow Water Equivalency Sensor - Page 33

... CS725 installed prior to determine the n0K and n0Tl values. 25 Campbell Scientific technical support will need to be contacted so that calculations can be in percent by weight [100 *(mass of water/mass of dry soil)]. • Measure the final installed height of 30 cm. However, when well-drained soils are required for the final setup...
CS725 Snow Water Equivalency Sensor - Page 34

... on the histogram : 245 [8] Collim (1: Collimator installed; 0: no snow present, then the following needs to be done to complete the setup: Access the Parameter menu of the CS725 via the terminal emulator by running the CS725 for the 99 command to avoid an inadvertent save. • The setting can also be made based on EPROM...
CS725 Snow Water Equivalency Sensor - Page 35

... 100 ft) 9600 Terminal settings should be as Hyperterminal will be required to transfer the new firmware file to a Computer). Once the terminal program is setup and the CS725 is connected to the computer using the DB9F-TERM (see Section 4, Connecting the CS725 to the CS725. The following will need to be enabled. Firmware Update (using the RS...

Campbell Scientific CS725 Reviews

Do you have an experience with the Campbell Scientific CS725 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Campbell Scientific yet.

Popular Campbell Scientific CS725 Search Terms

The following term is frequently used to search for Campbell Scientific CS725 support:

Ask a New Question
Use the box below to post a new question about Campbell Scientific CS725.
Manuals / Documents
Download any of our Campbell Scientific CS725 manuals for free!

We have the following 1 documents available for the Campbell Scientific CS725:
  • CS725 Snow Water Equivalency Sensor
Related Items
View other Campbell Scientific Electronics Accessories:

Points & Prizes
  • You can earn points for nearly everything you do on HelpOwl.com
  • You can trade in those points for gift cards at leading retailers such as Amazon.com and Walmart
  • It's that simple!
See How it Works
Create a Free Account

Campbell Scientific Manuals

Find free Campbell Scientific CS725 manuals and user guides available at ManualOwl.com. Try out our unique manual viewer allowing you to interact with manuals from directly within your browser!

Campbell Scientific Reviews

View thousands of Campbell Scientific CS725 user reviews and customer ratings available at ReviewOwl.com.

Contact Information

Complete Campbell Scientific customer service contact information including steps to reach representatives, hours of operation, customer support links and more from ContactHelp.com.

Scoreboard Ratings

See detailed Campbell Scientific customer service rankings, employee comments and much more from our sister site.