Campbell Scientific 109SS Support and Manuals
Get Help and Manuals for this Campbell Scientific item
This item is in your list!
View All Support Options Below
Free Campbell Scientific 109SS manuals!
Problems with Campbell Scientific 109SS?
Ask a Question
Free Campbell Scientific 109SS manuals!
Problems with Campbell Scientific 109SS?
Ask a Question
Popular Campbell Scientific 109SS Manual Pages
109SS Temperature Probe - Page 3
... is limited to repairing or replacing (at www.campbellsci.com.) Products not manufactured by CSI, but that are resold by CSI, are available for installation services performed by CSI such as programming to customer specifications, electrical connections to Products manufactured by CSI, and Product specific training, is in the corresponding product manual. (Product manuals are warranted only...
109SS Temperature Probe - Page 4
...contaminants that may not be returned to determine which Campbell Scientific company serves your country. directly. Campbell Scientific is not received within their territories. Assistance
Products may cause health or safety concerns for our employees. Affiliate companies handle repairs for customers within three days of the problem, an RMA number will be returned without prior...
109SS Temperature Probe - Page 7
...to get started.
1. Install Short Cut by clicking on each product. and passes FMVSS302. Contact Campbell Scientific to facilitate repair or replacement.
• Check model information against the shipping documents to temperature extremes, moisture, and UV degradation. Model numbers are received. Introduction
The 109SS Temperature Probe uses a thermistor to Campbell Scientific.
4. Use the...
109SS Temperature Probe - Page 8
Click Next.
2 Select Datalogger Model and Scan Interval (default of 5 or 10 seconds is OK for most applications). When Short Cut opens, select New Program.
4. Model 109SS Temperature Probe 3.
109SS Temperature Probe - Page 9
...Available Sensors and Devices list, select the Sensors |
Temperature folder. Model 109SS Temperature Probe 5. Data defaults to complete the program. After selecting the sensor, ...sensors are outlined in Short Cut Help, which is accessed by clicking the Deg C box and selecting Deg F, for degrees Fahrenheit, or K, for Kelvin.
6. This can be wired to the Selected device window. Select 109...
109SS Temperature Probe - Page 10
... sensor in harsh, corrosive environments. It can click Finish in a stainless-steel sheath. Also compatible with Campbell Scientific CRBasic dataloggers CR200(X) series, CR800 series, CR1000, CR3000, and CR5000. Model 109SS Temperature Probe
8. Specifications
Features: • Measures soil or water temperature • Compatible with AM16/32-series multiplexers • Easy to install...
109SS Temperature Probe - Page 11
...specification and the accuracy of the thermistor. Worst-case probe and measurement errors
Error Degrees C
Steinhart & Hart - The Steinhart-Hart equation used in CRBasic instruction Therm109() (CRBasic dataloggers) has negligible error... error
1The overall probe accuracy is the interchangeability specification of the bridge resistor. Maximum Steinhart-Hart Linearization Error:
Model 109SS ...
109SS Temperature Probe - Page 12
Programming code is the best source for a new datalogger installation. • Adding sensors to an existing custom program.
6... can probably create and maintain a datalogger program exclusively with Short Cut, skip Section 7.1, Wiring to Datalogger
TABLE 7-1. Model 109SS Temperature Probe
Stainless-Steel Sheath Diameter: 0.16 cm (0.063 in) Length: 5.84 cm (2.3 in)
Overmolded Joint ...
109SS Temperature Probe - Page 13
... °C -
set Mult to 1 and Offset to import Short Cut code into a Program Editor. It makes a half-bridge resistance measurement and converts the result to temperature using a fifth-order polynomial to convert the measurement to measure the 109SS probe in the following sections. Variations:
• Temperature reported as °F - The Therm109() measurement instruction programs...
109SS Temperature Probe - Page 15
... to the soil surface at the Vs line.
9 Operation
8.1 Sensor Schematic
FIGURE 8-1. 109SS thermistor probe schematic
8.2 Measurement and Output Linearization
Campbell Scientific dataloggers measure the 109SS probe thermistor and convert the result to 45 m (150 ft) or 63 psi. Model 109SS Temperature Probe
7.3 Water Temperature Installation
109SS probes can be submerged to temperature.
109SS Temperature Probe - Page 16
... for Rs:
Rs + 24900 = 24900 • (Vx/Vs)
Rs = 24900 • ((Vx/Vs) - 1)
TABLE 8-1, 109SS Measurement Details, and TABLE 8-2, 109SS Temperature Calculation, describe how measurement results Vs/Vx and Rs are converted to temperature by Campbell Scientific dataloggers. Mathematical instructions calculate and pre-scale ln(Rs) by 1E-3
Equation Applied to Scaled Result
Steinhart-Hart...
109SS Temperature Probe - Page 17
... dataloggers. The following code examples filter 60 Hz noise. Depending on the datalogger model, this noise can be a significant source of measurement error. 60 Hz noise ...is common in the United States. 50 Hz noise is common in Europe and other regions. Model 109SS Temperature Probe
where:...
109SS Temperature Probe - Page 18
...as specified by the measurement instruction, and the purple wire is reported. Troubleshooting and Maintenance
NOTE
All factory repairs and recalibrations require a returned ...,CR7: 5000 mV
7: 3
Loc [V_Vx ]
8: .0004
Multiplier
9: 0.0
Offset
9. Model 109SS Temperature Probe
Therm109(T109_C,1,1,1,20000,_60Hz,1.0,0.0)
NOTE
Integration options and the settling time parameter are correct ...
109SS Temperature Probe - Page 19
... intrusion.
9.3 Calibration
Calibration of the 109SS probe is a registered trademark of the... °C outputs 0.1 °C. Model 109SS Temperature Probe
9.2 Maintenance
The 109SS probe requires minimal maintenance. Attributions and... ATUM is a trademark of Tyco Electronics Corporation. For example, a 109SS probe placed in a calibration chamber at 0 °C, the polynomial calculates a...
109SS Temperature Probe - Page 25
...adaptation will be used with CR10X dataloggers. Contact a Campbell Scientific application engineer for help with the 21X and CR7 ...X Loc [ lnRt
]
F
Z Loc [ Scal_lnRt ]
B-3 With minor adaptations, it can be needed with any datalogger program.
;{CR10X}
;Program measures one 109 temperature probe once a second ;and stores the average temperature every 60 minutes.
;Wiring Diagram...
Campbell Scientific 109SS Reviews
Do you have an experience with the Campbell Scientific 109SS that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Campbell Scientific yet.
Earn 750 points for your review!