Campbell Scientific 52202 Support and Manuals
Get Help and Manuals for this Campbell Scientific item
View All Support Options Below
Free Campbell Scientific 52202 manuals!
Problems with Campbell Scientific 52202?
Ask a Question
Free Campbell Scientific 52202 manuals!
Problems with Campbell Scientific 52202?
Ask a Question
Popular Campbell Scientific 52202 Manual Pages
52202 Electrically Heated Rain and Snow Gage - Page 1
52202 Electrically Heated Rain and Snow Gage
Revision: 5/11
Copyright © 2010-2011 Campbell Scientific, Inc.
52202 Electrically Heated Rain and Snow Gage - Page 2
.... This warranty shall not apply to the customer at www.campbellsci.com/repair. Products may cause health or safety concerns for installation services performed by Campbell Scientific, Inc. ("Campbell") to be either emailed to repair@campbellsci.com or faxed to modification, misuse, neglect, improper service, accidents of the shipping container. The form is not received within their...
52202 Electrically Heated Rain and Snow Gage - Page 3
...Specifications 1
3. Wiring 4
4.1 Heater Wiring 4 4.2 Wiring to a Pulse Channel 4 4.3 Wiring to a Crossarm 3 3-3. The CM220 Mounted to a Control Port 5
5. Multipliers 5
i Installation 2
3.1 Siting...2 3.2 Mounting 2
4. Troubleshooting...CR10X Example Program 9
6. Maintenance 10
Figures
3-1. 52202 Precipitation Gage 2 3-2. The CM216 Atop a Stainless-Steel Tripod 3
...
52202 Electrically Heated Rain and Snow Gage - Page 5
... model number indicates that plugs into a wall socket and provides 24 Vac.
However, this manual, the rain gage will be used with magnetic reed switch
Accuracy: 2% up to as slow burning when tested according to U.L. 94 H.B. and will support combustion in . (30 cm)
NOTE
The black outer jacket of strong winds on the 52202...
52202 Electrically Heated Rain and Snow Gage - Page 6
... Wind Screen's siting information and installation procedure are provided in a relatively level spot which is shipped with the 52202 gage. above the average snow depth. It should not be mounted in the 260-953 manual.
3.1 Siting
The 52202 should be placed away from objects that obstruct the wind.
52202 Electrically Heated Rain and Snow Gage...
52202 Electrically Heated Rain and Snow Gage - Page 7
... (see Figure 3-3). Fits in . The crossarm attaches to a tripod mast, tower leg, CM300-series mounting pole, or a user-supplied vertical pipe (1.0-in . to 2.1-in . OD).
52202 Electrically Heated Rain and Snow Gage
The pipe attaches to a CM202, CM204, or CM206 crossarm via the CM216 Sensor Mounting Kit.
52202 Electrically Heated Rain and Snow Gage - Page 8
... to the channels shown on the wiring diagram created by performing the following the instructions supplied with the plug. Replace housing and retighten screws. Failure to do so may result in personal injury or death due to service or repair this equipment. Remove shipping retainer from bucket. Adjust leveling screws until bulls eye level...
52202 Electrically Heated Rain and Snow Gage - Page 9
... the units in which rainfall is measured using Campbell Scientific's Short Cut Program Builder software.
You do not need to read the output from the rain gage switch must be generated using a Pulse Count with the Pulse Count instruction.
5. 52202 Electrically Heated Rain and Snow Gage
4.3 Wiring to a Control Port
Dataloggers listed in Table...
52202 Electrically Heated Rain and Snow Gage - Page 10
52202 Electrically Heated Rain and Snow Gage
5.1.1 CR1000 Example Program
'CR1000
'RM_Young Tipping Blk > P1
'
Wht > ground
... Data Tables DataTable(Rain,True,-1)
DataInterval(0,60,Min) Totalize(1,Rain_mm,0) EndTable
'Main Program BeginProg
Scan(1,Sec)
'52202 Rain Gage measurement Rain_mm: PulseCount(Rain_mm,P_SW,2,0,0.1,0)
'Call Data Tables and Store Data CallTable(Rain) NextScan EndProg
6
52202 Electrically Heated Rain and Snow Gage - Page 11
... and CR3000. 52202 Electrically Heated Rain and Snow Gage
5.1.3 CR10X Example Program
;{CR10X}
*Table 1 Program
01: 1.0000
Execution Interval (seconds)
1: Pulse (P3) 1: 1 2: 1 3: 2 4: 3 5: 0.1 6: 0
Reps Pulse Channel 1 Switch Closure, All Counts Loc [ Rain_mm ] Multiplier Offset
2: If time is (P92) 1: 0 2: 60 3: 10
Minutes (Seconds --) into a Interval (same units as above) Set Output Flag...
52202 Electrically Heated Rain and Snow Gage - Page 12
52202 Electrically Heated Rain and Snow Gage
5.2.1 CR1000 Example Program
'CR1000
'RM_Young Tipping Blk > C4
'
Wht > 5v
'Cabling for heater goes to 24VAC power supply
'Declare ...
52202 Electrically Heated Rain and Snow Gage - Page 13
Troubleshooting
6.1 Precipitation
Symptom: No Precipitation
1. Check that the Configuration Code (Switch Closure), and Multiplier and Offset parameters for the Pulse Count instruction...is (P92) 1: 0 2: 60 3: 10
Minutes (Seconds --) into a Interval (same units as above) Set Output Flag High (Flag 0)
3: Set Active Storage Area (P80)
1: 1
Final Storage Area 1
2: 101
Array ID
4: Real Time (P77)...
52202 Electrically Heated Rain and Snow Gage - Page 14
...at the terminal block on the inside of 50 ±1. If the count shows an error of the switch. 52202 Electrically Heated Rain and Snow Gage 3. With the rain gage properly leveled, slowly pour ...ohm when the bucket is balanced.
7. Leveling screws may be counted manually or with a counter connected to ensure measurement accuracy. Bucket tips may be desirable to the rain gage terminals. ...
Campbell Scientific 52202 Reviews
We have not received any reviews for Campbell Scientific yet.