Campbell Scientific CR211X Support and Manuals
Get Help and Manuals for this Campbell Scientific item
View All Support Options Below
Free Campbell Scientific CR211X manuals!
Problems with Campbell Scientific CR211X?
Ask a Question
Free Campbell Scientific CR211X manuals!
Problems with Campbell Scientific CR211X?
Ask a Question
Popular Campbell Scientific CR211X Manual Pages
CR200/CR200X-series Dataloggers - Page 3
... manufactured by surface carrier prepaid within the continental United States of Campbell's product warranty. Warranty
"PRODUCTS MANUFACTURED BY CAMPBELL SCIENTIFIC, INC. This warranty is part of America. The warranty for installation services performed by Campbell such as programming to customer specifications, electrical connections to be the sole and exclusive remedy under this...
CR200/CR200X-series Dataloggers - Page 4
... exposed to contaminants that may not be either emailed to repair@campbellsci.com or faxed to refuse service on the outside of the problem, an RMA number will be issued. A completed form must fill out a "Statement of product receipt or is for our employees. Campbell Scientific reserves the right to (435) 227-9106. Assistance
Products...
CR200/CR200X-series Dataloggers - Page 13
...-gravity in -depth study requires other Campbell Scientific publications are unable to those more information is to guide you to the tools you need to...Campbell Scientific products are defined by spending a few minutes working through a first attempt at support@campbellsci.com.
1.1
CR200(X) series Datalogger Models
Models CR200X and CR200 Dataloggers do not have a built-in the manual...
CR200/CR200X-series Dataloggers - Page 46
... combined telecommunication options, customized data monitoring displays, and scheduled data collection. Several datalogger support software products for Windows are included for datalogger setup and simple applications, PC200W and Short Cut, are available from Campbell Scientific.
• PC200W Starter Software is available at no cost at www.campbellsci.com. Short Cut and CRBASIC Editor...
CR200/CR200X-series Dataloggers - Page 49
... Support
...instruction, which is required to understand their limitations. The CR200(X) is enough to power many sensor types. Switched Unregulated (Nominal 12 Volt) (p. 38) shows the current limits of these channels in TABLE. Check the accuracy specification of SW Battery. Section 4. Current Sourcing Limits p. 38 are typically used to measure many sensors. Contact a Campbell Scientific...
CR200/CR200X-series Dataloggers - Page 53
...that is one calibration measurement is typically measured with Campbell Scientific's 109-L thermistor probe.
FIGURE. Vx is the...precision fixed (static) resistor.
Therm109 () is made per instruction regardless of the number of the other resistor in the...and position potentiometers are examples. Sensor Support
4.2.5
Self-Calibration
A calibration measurement to compute the...
CR200/CR200X-series Dataloggers - Page 54
... is such that require AC excitation.
4.4 Pulse Count Measurement
FIGURE.
Other Campbell Scientific dataloggers (e.g. Figure 29: Switch Closure Pulse Sensor 42
Sensors requiring AC excitation...new counter value. Sensor Support
4.3.1
Measurements Requiring AC Excitation
Some resistive sensors require AC Excitation.
Activated by the PulseCount () instruction, dedicated 16-bit counters...
CR200/CR200X-series Dataloggers - Page 57
...I /O channel specifications in Specifications p. 35. ...-collector (open-drain) output devices for high-frequency input. Contact Campbell Scientific for measuring low-level AC output sensors. The specified number of ...measured directly on the P_SW input is 6.5 V. Sensor Support
When a pulse channel is configured for the PulseCount () instruction. If pulse inputs greater than +6.5 V need to ...
CR200/CR200X-series Dataloggers - Page 58
... gages currently sold by Campbell Scientific.
As shown in a Tipping Bucket Rain Gage Circuit
46 Current Limiting Resistor in series at the switch to the SDI-12 sensor. This resistor is connected in a Rain Gage Circuit (p. 46), a 100 ohm resistor is installed on sensor response and accuracy. Section 4. Sensor Support
4.6 SDI-12 Recording
Read...
CR200/CR200X-series Dataloggers - Page 59
Campbell Scientific does not recommend SDI-12 sensor lead lengths greater than 200 feet; however, longer lead lengths can sometimes be accommodated by increasing the wire gage and/or powering the sensor with a second 12 vdc power supply placed near the sensor.
47 Section 4. Sensor Support
4.7.3 Serial Sensors
4.7.3.1 SDI-12 Sensors
The SDI-12 standard allows cable lengths of up to 200 feet.
CR200/CR200X-series Dataloggers - Page 117
... PakBusGraph "Hop Metrics" to the CR200(X)'s RS232 port. Also see Campbell Scientific PakBus® Networking Guide available at www.campbellsci.com.
Otherwise, the result code increments. The Timeout parameter in these instructions is in CRBASIC like any other variable. Peer-to-peer PakBus® instructions enable the datalogger to the device is not yet known, a direct...
CR200/CR200X-series Dataloggers - Page 128
...12 transparent mode, enter the support software terminal emulator. command.
Click the "Open Terminal" button. command is in SDI12Recorder () instruction. z, and A - If program mode communications is useful in troubleshooting SDI-12 systems because it responds to finish before transparent mode can manually interrogate and enter settings in transparent mode, datalogger programs...
CR200/CR200X-series Dataloggers - Page 154
...reverse byte order words, the CR200(X) does not have that supports the MoveBytes() instruction.
15.1.4 Troubleshooting
Test Modbus functions on the CR200(X) with third party Modbus ...software. Section 15. Further information is sometimes possible, or the CR200(X) needs to replaced with...
CR200/CR200X-series Dataloggers - Page 179
... of power from the CR200(X) or a peripheral to do. Transfer is set by the program entered in Intermediate Storage. Denotes a) the information carrier generated by Output Processing Instructions is to another device. output interval The time interval between Campbell Scientific instrumentation.
Once the instruction number has been entered in Input Storage. The ultimate destination of...
CR200X-Series Specifications - Page 1
...criteria available on , program controlled Cycle Time: 1 or 8 s cycles;
contact Campbell Scientific
WARRANTY
Three year covering parts and labor. DIGITAL I/O
Channels SE1 to SE5 can program datalogger to measure internal... system configuration and critical specifications with 0 dBd ½ wave antenna (line-of 03/02)
CE COMPLIANT DATALOGGERS: CR200X, CR206X, CR211X, CR216X
STANDARD(S) TO ...
Campbell Scientific CR211X Reviews
We have not received any reviews for Campbell Scientific yet.