Campbell Scientific CR9000XC Support and Manuals
Get Help and Manuals for this Campbell Scientific item
View All Support Options Below
Free Campbell Scientific CR9000XC manuals!
Problems with Campbell Scientific CR9000XC?
Ask a Question
Free Campbell Scientific CR9000XC manuals!
Problems with Campbell Scientific CR9000XC?
Ask a Question
Popular Campbell Scientific CR9000XC Manual Pages
CR9000X Measurement and Control System - Page 5
... QS-2 QS1.2 Opening Enclosure QS-2 QS1.3 Connecting the RS232 Port/ Card Installation QS-2 QS1.4 Powering the Logger QS-3 QS1.5 Setting Up Serial Communications QS-3 QS1.6 Setting Up IP Communications QS-9
QS2. Specifications OV-27
1. Program Generator Basics QS-12 QS2.1 Program Generator Summary Window QS-12 QS2.2 Program Generator Configuration Window QS-13 QS2...
CR9000X Measurement and Control System - Page 41
... Protected 5 V Analog Input Module
Overview
FIGURE OV1-6.
Another difference from the CR9000X chassis. See Section 7 Measurement Instructions for measurement details. The CR9050EC contains the PRT that is 1.6 μV. The CR9051E supports the same instruction set as to provide the reference temperature for thermocouple measurements. The maximum aggregate throughput for the CR9050...
CR9000X Measurement and Control System - Page 49
... average parameter of 10 KHz. CR9070 SUPPORTED MEASUREMENT/CONTROL INSTRUCTIONS:
PulseCount Count Pulses or Frequency
ReadI/O
Read State of I /O Channels... instruction in a 1 second scan has a frequency resolution of 1 Hz, a 0.5 second scan gives a resolution of 2 Hz, and a 1 ms scan gives a resolution of I /O Channels
TimerIO
Interval and Timing Measurements
WriteI/O Set ...
CR9000X Measurement and Control System - Page 51
...The minimum input voltage that have transitions from such sensors as a magnetic pickups.
CR9071 SUPPORTED MEASUREMENT/CONTORL INSTRUCTIONS:
PulseCount Count Pulses or Frequency
ReadI/O
Read State of I/O Channels
TimerIO
Interval and Timing Measurements
WaitDigTrig Trigger Measurement Scan
WriteI/O Set State of I/O Channels
See Section 3.4 Pulse Count Measurements for Control...
CR9000X Measurement and Control System - Page 90
...instructions that may vary the sequence and timing of the measurement.
When the CR9000X Reverses the differential input or the excitation polarity, it delays the same time after the reversal as 5.005 mV. These are not part of the excitation voltage (RevEx), reverse the high and low differential inputs (RevDiff), to set...its accuracy specifications. Most ... always a setup time for ...
CR9000X Measurement and Control System - Page 243
.... CAN identifiers for the voltages (millivolts) that holds the values for a "specific" SDM-CAN must be set using this parameter is used to set . Section 7. See CSAT3 manual for the SDMTrigger instruction. Address 15 is being set to each channel of the Reps.
If this instruction. Valid SDM addresses are sent to +5000 mV (-5000 mV).
Multiple...
CR9000X Measurement and Control System - Page 252
...
Funct8_5 Funct4_1
Constants
Enter SDMINT8 PARAMETERS
The array where the results of the instruction are set to at the factory for address
00. If the "Capture All Events"... functions. For example, the code entered
for one dimensional array with the CR9000X. See section 5.3 of the INT8 manual for further details.
See Appendix A of the INT8 manual for details on changing the ...
CR9000X Measurement and Control System - Page 262
... that store the results from its previous value. If this (see PulseCountReset Example 2 below ). The first Scan after the PulseCount instruction.
Section 7.
This instruction cannot be changed through program control to 0 or NAN (example programs set it to DataTables that have calls to the Subroutine call should be the value from the PulseCount...
CR9000X Measurement and Control System - Page 360
... buffers setup by the Scan instruction. DATA 1, 2, 3, 4 For I = 1 To 4
READ X( I ) Next I RESTORE For I = 1 To 4
READ Y( I ) Next I
Excite (ExSlot, ExChan, ExmV, Delay)
This instruction sets the ...by the instruction unless a subsequent instruction (Excite or a Bridge instruction) changes the voltage setting for the measurement. As long as this task will be switched to a specific value. ...
CR9000X Measurement and Control System - Page 439
..., 8-34 Specifications, OV-27 Spectral Leakage, 3-34 Spectral Options, 7-53 Spectral Options, 8-17 Spectral Weighing, Class A, B, & C, 7-51 SpltStr String Function, 11-8 Sqr, Square Root Function, 8-35 Standard Deviation, 6-33 Standard Deviation, Spatial, 8-35 Startup Code, D-1 State, OV-16, OV-18, E-9 Station Name, 5-11 Status Table, D-1 StdDev Instruction, 6-33 StdDevSpa Instruction, 8-35...
RTDAQ Software - Page 33
... access the CD-ROM drive and select the setup executable.
Skip to run RTDAQ, you will be advised as to complete the installation. If you choose to purchase RTDAQ, you may wish to your CD case.
Section 3. Installation, Operation and Backup Procedures
3.1 CD-ROM Installation
The following instructions assume that the trial version will each...
RTDAQ Software - Page 66
... to the part of the text.
Moves the cursor to search for in the program. Compile - Starts the compiler to successive occurrences of the program where the next error was identified. You can replace all occurrences of the program where the previous error was identified. Redo -
Toggle Bookmark -
Find -
Instruction Panel - Hiding the Instruction Panel allows...
RTDAQ Software - Page 240
...menu item opens the Editor Preferences screen used , traces plotted, etc. Undo cancels the last change some global settings that are toggles. By default, this is disabled. When a data value changes, the component will be ...projects.)
The Customize menu item allows you can then be updated per second, disable animation when a data value changes, and specify whether high quality or high speed...
RTDAQ Software - Page 242
...careful about the alignment you set the component properties, placement and alignment. Select one of the RTMC clipboard content on top of the selected component.
Manual Resize lets you choose.
...for the selected component. With the components selected choose one or more objects to set the size and position of each other components while holding down the page. ...
RTDAQ Software - Page 340
... is connected and has power, check the security setting in the datalogger and in Setup, check that fails, follow the steps for all the devices in the reason code.
Getting the datalogger table definitions will erase any data in one block and the next part is busy with the datalogger by trying to check...
Campbell Scientific CR9000XC Reviews
We have not received any reviews for Campbell Scientific yet.