Brother International VX3250F Support and Manuals
Get Help and Manuals for this Brother International item
View All Support Options Below
Free Brother International VX3250F manuals!
Problems with Brother International VX3250F?
Ask a Question
Free Brother International VX3250F manuals!
Problems with Brother International VX3250F?
Ask a Question
Brother International VX3250F Videos
Unboxing máquina Familiar | Brother VX3250F | Profe Suescún | 4K
Duration: 22:36
Total Views: 2,111
Duration: 22:36
Total Views: 2,111
Popular Brother International VX3250F Manual Pages
Operation Manual - Page 5
... SEWING MACHINE 7
Connecting plugs 7 Main power and sewing light switch 8 Foot controller 8 Checking the needle 8 Replacing the needle 8 Changing the presser foot 10
THE CONTROLS 11
Pattern selection dial 11 Patterns and stitch names 11 Reverse sewing lever 12
THREADING THE MACHINE 13
Winding the bobbin 13 Lower threading 15 Lower threading (for models equipped with a quick-set...
Operation Manual - Page 6
...XA5539-151
No.
Part Code Americas Others 3-piece set: XE5328-001 2-piece set (90/14 needle)
6 Screwdriver
7 Foot controller
Note
● The included accessories vary depending on the machine model. No. A
A
I
I "
XE9369-001
4
Bobbin (One is on the model you easily perform most sewing tasks.
1.
2.
3.
4.
5.
M
M
6.
7.
8.
9.
10. Part Name
Part Code Americas Others...
Operation Manual - Page 7
... guide (Page 13, 17) This is only available on certain models.)
0 Flat bed attachment with accessory compartment (Page 6)
A Presser foot (Page 10)
B Reverse sewing lever (Page 12) Push this to control the sewing speed, and to start and stop sewing.
J Handle Carry the machine by its handle when transporting. Contact your Brother dealer or the nearest authorized Brother Service...
Operation Manual - Page 8
... shock. Connect the power supply plug to correctly operate the machine.
(For U.S.A. When restarting the sewing machine, follow the necessary procedure to a wall 2 outlet. Always grasp the plug to
remove it still does not fit, contact a qualified electrician to your authorized Brother Service Center for repairs before continuing use extension cords or multi-plug adapters with...
Operation Manual - Page 9
...machine will run at a low speed. Replacing the needle
CAUTION
● Always turn on the wheel points up on the machine with a bent needle. Otherwise, injuries may occur if the foot controller is accidentally pressed and the machine starts sewing.
● Only use sewing machine needles for smooth sewing... machine may bend or break and cause injury.
● Never sew with product code 888...
Operation Manual - Page 10
...parts of the machine, insert the needle
until it touches the stopper, and securely tighten the needle clamp screw with a screwdriver, otherwise the needle may break or the machine may be damaged.
Next, tighten the needle clamp using a screwdriver.
2
3
1
1 Use a screwdriver 2 Needle stopper 3 Needle
Install...
9 KNOWING YOUR SEWING MACHINE
CAUTION
● Before replacing the needle, place...
Operation Manual - Page 12
...*1 : Stitch nos. 15-17 are only available on the wheel points up.
KNOWING YOUR SEWING MACHINE
THE CONTROLS
Pattern selection dial
CAUTION
● When you use the pattern selection dial to choose ... selection dial in the down position when you (counterclockwise) so that the mark on certain models. Pattern Stitch Name
1
Preset Length (mm (inch))
Preset Width (mm (inch))
Reference...
Operation Manual - Page 14
... the thread from other bobbins may tangle on the thread guide. Actual size
11.5 mm (7/16 inch)
This model
Other models
1
1 Pull the thread in the groove on the spool pin. Only use bobbins from the spool 2 with this machine. KNOWING YOUR SEWING MACHINE
THREADING THE MACHINE
Winding the bobbin
CAUTION
● We designed the bobbin that...
Operation Manual - Page 15
... damage to loosen, and may tangle around the bobbin a few times. Then stop the machine. Note
● When the sewing machine is started or the handwheel is not a malfunction.
● The needle bar does not move when you follow the instructions carefully. Cut the thread, slide the bobbin winder 0 shaft to 10 cm (3-4 inches...
Operation Manual - Page 16
...machine starts to sew, you set bobbin, see page 16.
Remove the bobbin cover by turning the 2 handwheel toward you
(counterclockwise) and raise the presser foot lever.
KNOWING YOUR SEWING MACHINE
Lower threading
Install...right direction. CAUTION
● Make sure you .
1
Hold the end of the machine (as shown.
• If the thread is not correctly inserted through the tension-adjusting...
Operation Manual - Page 18
KNOWING YOUR SEWING MACHINE
Upper threading
2
2
3 4
1 5
1 Spool pin 2 Thread guide (back) 3 Thread guide (front)
4 Thread take-up lever 5 Mark on the wheel ...foot lever.
2
Pull up .
• If the needle is not correctly raised, the sewing machine can not be threaded.
If the upper threading is set incorrectly, the thread may bend or break.
● Never use a thread weight of ...
Operation Manual - Page 19
... your sewing machine is lowered, the upper thread can easily be wrapped around the thread take-up lever before you feed the upper thread.
● If you incorrectly feed the thread you may cause sewing problems.
18...with your right hand, pass the thread
Put the thread behind the needle bar thread guide by turning the handwheel toward you raise the presser foot lever and the thread take-up...
Operation Manual - Page 20
... hook passes through 100/16 home sewing machine needle. KNOWING YOUR SEWING MACHINE
Using the needle threader (for models equipped with a 65/9 home sewing machine needle. Lower the presser foot lever...threader lever, 4 hook the thread onto the guide.
2
1
1 Needle holder 2 Needle threader lever
1 2
3
1 Needle holder 2 Needle threader lever 3 Guide
Pull down the needle threader lever as 5 ...
Operation Manual - Page 22
... then raise the needle.
■ For models equipped with a quick-set bobbin
You can draw up the lower thread by hand to draw up the 2 lower thread.
1 2
1
• The bobbin cover should still be left over.
Pass the thread along the slit in .
KNOWING YOUR SEWING MACHINE
Drawing up the lower thread
While lightly...
Operation Manual - Page 43
...Attach the presser foot that is incorrectly installed. Contact your retailer or the nearest
- Loosen the upper thread tension.
27
42 for this machine.
13
You have not fitted the spool properly.
authorized Brother Service Center. TROUBLESHOOTING
If the machine stops operating correctly, check the following possible problems before requesting service. Use the screwdriver to
-
Brother International VX3250F Reviews
We have not received any reviews for Brother International yet.