Installation Instructions
Page 2
Table of Contents Safety 1 Important Safety Instructions 1 Installation 4 Before You Begin 4 Overview 4 Tools and Parts Needed 4 Parts Included 5 General Information 5 Preparation 5 Installation Procedure 11 Apply Foam Tape 11 Install Backwall Trim 11 Connect Electric 12 Connect Gas Supply 16 Test for Gas Leaks 21 Test the Installation 22 Service 24 Before Calling Service 24 Product Data Plate 24 Questions? 1-800-944-2904 www.boschappliances.com 5551 McFadden Ave. Huntington Beach, CA 92649 We look forward to hearing from you!
Table of Contents Safety 1 Important Safety Instructions 1 Installation 4 Before You Begin 4 Overview 4 Tools and Parts Needed 4 Parts Included 5 General Information 5 Preparation 5 Installation Procedure 11 Apply Foam Tape 11 Install Backwall Trim 11 Connect Electric 12 Connect Gas Supply 16 Test for Gas Leaks 21 Test the Installation 22 Service 24 Before Calling Service 24 Product Data Plate 24 Questions? 1-800-944-2904 www.boschappliances.com 5551 McFadden Ave. Huntington Beach, CA 92649 We look forward to hearing from you!
Installation Instructions
Page 3
... ranges can cause injury or property damage. Remove the door for guidance. Refer to this manual for easier handling and installation. For example, do not remove leveling legs, panels, wire covers or anti-tip brackets/screws. • To eliminate the risk of burns or fire by a qualified technician. Verify that cabinets above the surface units should be reduced by installing a hood that projects horizontally a minimum of 5 inches beyond...
... ranges can cause injury or property damage. Remove the door for guidance. Refer to this manual for easier handling and installation. For example, do not remove leveling legs, panels, wire covers or anti-tip brackets/screws. • To eliminate the risk of burns or fire by a qualified technician. Verify that cabinets above the surface units should be reduced by installing a hood that projects horizontally a minimum of 5 inches beyond...
Installation Instructions
Page 4
... a power-supply cord kit rated for this manual. • The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing at the service panel. show the owner the location of the circuit breaker or fuse. nician. Installation, electrical connections and grounding must comply with all controls are in the OFF position. • For appliances equipped with a cord and plug, do not cut or remove the...
... a power-supply cord kit rated for this manual. • The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing at the service panel. show the owner the location of the circuit breaker or fuse. nician. Installation, electrical connections and grounding must comply with all controls are in the OFF position. • For appliances equipped with a cord and plug, do not cut or remove the...
Installation Instructions
Page 5
... electrical switch. • Do not use with its own high pressure regulator. Follow the gas supplier's instructions. • If you cannot reach your gas supplier from the factory for use with natural gas. Exception: For use with propane the appliance must be converted per the LP conversion instructions. • For Massachusetts installations: • Installation must be converted for safe operation up to a height of this appliance is being installed. • Shut-off valve...
... electrical switch. • Do not use with its own high pressure regulator. Follow the gas supplier's instructions. • If you cannot reach your gas supplier from the factory for use with natural gas. Exception: For use with propane the appliance must be converted per the LP conversion instructions. • For Massachusetts installations: • Installation must be converted for safe operation up to a height of this appliance is being installed. • Shut-off valve...
Installation Instructions
Page 6
... and Parts Needed Additional Parts Needed For Hard Wire Installations • Range Power Supply Cord Kit (240V -30 Amp) Note: Not necessary for step-by-step instructions. Connect Gas Supply 6. Connect Electric 5. Test for Anti-Tip Bracket (Style will vary depending on mounting surface) • Level • Drill and Drill Bit • Soapy Water • Pipe Wrench • Teflon Tape • Channel Lock Pliers • Gas Leak Test Solution • Gas Supply Line • Gas Shut Off Valve...
... and Parts Needed Additional Parts Needed For Hard Wire Installations • Range Power Supply Cord Kit (240V -30 Amp) Note: Not necessary for step-by-step instructions. Connect Gas Supply 6. Connect Electric 5. Test for Anti-Tip Bracket (Style will vary depending on mounting surface) • Level • Drill and Drill Bit • Soapy Water • Pipe Wrench • Teflon Tape • Channel Lock Pliers • Gas Leak Test Solution • Gas Supply Line • Gas Shut Off Valve...
Installation Instructions
Page 7
.... Push down on the clip on the left rail. Parts Included General Information Overall Dimensions Level Preparation Prepare Unit • Anti-Tip Bracket • Foam Tape • Backwall Trim • Screws for Backwall Trim (2) • Terminal Lugs (For Use With Hard Wire Installations) Note: not necessary for Canadian installations Installation Table 2: Overall Dimensions Dimension Height Width Depth Inches 36" 31" 25 5/8" Centimeters 91.44 cm 78.74...
.... Push down on the clip on the left rail. Parts Included General Information Overall Dimensions Level Preparation Prepare Unit • Anti-Tip Bracket • Foam Tape • Backwall Trim • Screws for Backwall Trim (2) • Terminal Lugs (For Use With Hard Wire Installations) Note: not necessary for Canadian installations Installation Table 2: Overall Dimensions Dimension Height Width Depth Inches 36" 31" 25 5/8" Centimeters 91.44 cm 78.74...
Installation Instructions
Page 8
... could result in place before removing door. Electrical Requirements 4. See "Product Data Plate" on page 24 for more information. The electrical rating of the power cord set must be marked "For Use with a power cord set (not supplied). The power cord set aside. WARNING: When removing the door: • Make sure oven is cool and power to the oven has been turned off before attempting to remove oven door. 2. Close the door until it may swing in...
... could result in place before removing door. Electrical Requirements 4. See "Product Data Plate" on page 24 for more information. The electrical rating of the power cord set must be marked "For Use with a power cord set (not supplied). The power cord set aside. WARNING: When removing the door: • Make sure oven is cool and power to the oven has been turned off before attempting to remove oven door. 2. Close the door until it may swing in...
Installation Instructions
Page 9
... must be increased to determine amperage requirements. CAUTION: Make certain that the present electric service to verify that gas shutoff valve and all burner controls are dual rated for use on either in the main entrance panel or in your range according to relight the pilot on other gas appliances when you turn the gas back on page 8. Verify that wiring to house is adequate Contact your...
... must be increased to determine amperage requirements. CAUTION: Make certain that the present electric service to verify that gas shutoff valve and all burner controls are dual rated for use on either in the main entrance panel or in your range according to relight the pilot on other gas appliances when you turn the gas back on page 8. Verify that wiring to house is adequate Contact your...
Installation Instructions
Page 10
... in an easily accessible location. Allow a minimum of the gas shutoff valve. Important note for LP users The range is designed for use with natural gas. Typical Installation Note: The installer should inform the consumer of the location of 30 inches between cabinets where range is to be converted using the LP conversion kit. Prepare the countertop and cabinets as shown in Figure 4: Gas Supply Line and Electrical Outlet Placement. 7 1/2" (190.5 mm...
... in an easily accessible location. Allow a minimum of the gas shutoff valve. Important note for LP users The range is designed for use with natural gas. Typical Installation Note: The installer should inform the consumer of the location of 30 inches between cabinets where range is to be converted using the LP conversion kit. Prepare the countertop and cabinets as shown in Figure 4: Gas Supply Line and Electrical Outlet Placement. 7 1/2" (190.5 mm...
Installation Instructions
Page 11
... fire by installing a hood that the opening is to alter dimensions accordingly. If cabinet storage is at least 30 inches. If nonstandard cabinets are used, care should be avoided. Cabinets over the cooking surface and cabinets adjacent to those over heated surface units, cabinet storage space located above the surface units should be taken to be provided, the risk can also replace a freestanding range. centered 4in...
... fire by installing a hood that the opening is to alter dimensions accordingly. If cabinet storage is at least 30 inches. If nonstandard cabinets are used, care should be avoided. Cabinets over the cooking surface and cabinets adjacent to those over heated surface units, cabinet storage space located above the surface units should be taken to be provided, the risk can also replace a freestanding range. centered 4in...
Installation Instructions
Page 12
... most kitchens a certified hood rating of not less than 1/4" of flame retardant material which must be a minimum clearance of 30 inches between the top of the cooking surface and the bottom of a ventilation hood above : There must be covered with the hood. This is protected by safety standards, particularly self-cleaning ovens; Install Anti-Tip Bracket 1. English 10 Measure to adjacent materials: See Figure 7: Cabinet Preparation. Remove any...
... most kitchens a certified hood rating of not less than 1/4" of flame retardant material which must be a minimum clearance of 30 inches between the top of the cooking surface and the bottom of a ventilation hood above : There must be covered with the hood. This is protected by safety standards, particularly self-cleaning ovens; Install Anti-Tip Bracket 1. English 10 Measure to adjacent materials: See Figure 7: Cabinet Preparation. Remove any...
Installation Instructions
Page 14
... provided with your range cord must be removed from the range to "Connect Gas Supply" on page 16. Feed range cord through hole and strain relief up to terminal block. Strain reliefs vary. Once cord length/ slack has been adjusted, attach strain relief per instructions included with the range cord already installed. DO NOT remove entire range back panel. Three wire range cord The four wire range cord connection is shipped from range, install strain relief in...
... provided with your range cord must be removed from the range to "Connect Gas Supply" on page 16. Feed range cord through hole and strain relief up to terminal block. Strain reliefs vary. Once cord length/ slack has been adjusted, attach strain relief per instructions included with the range cord already installed. DO NOT remove entire range back panel. Three wire range cord The four wire range cord connection is shipped from range, install strain relief in...
Installation Instructions
Page 15
... prohibited, (a) disconnect the link from the neutral, (b) use 4-conductor cord for this purpose). Figure 12: Grounding Requirements WARNING: To prevent electrical shock, the grounding prong on the range cord should not be installed per instructions included with Ranges". If there is any circumstances. Grounding through a ground strap. Four Wire Range Cord Connection 1. Remove the terminal block cover to neutral through the neutral conductor is prohibited...
... prohibited, (a) disconnect the link from the neutral, (b) use 4-conductor cord for this purpose). Figure 12: Grounding Requirements WARNING: To prevent electrical shock, the grounding prong on the range cord should not be installed per instructions included with Ranges". If there is any circumstances. Grounding through a ground strap. Four Wire Range Cord Connection 1. Remove the terminal block cover to neutral through the neutral conductor is prohibited...
Installation Instructions
Page 18
... relief. Note: DO NOT plug in range at this time. The range can be converted using the LP conversion kit. Installation 7. Tighten all male pipe threads to relight the pilot on other gas appliances when you turn the gas back on. The gas connection is located below the back panel of DuPont English 16 1.Teflon is shipped from the back of the range. See "Install Strain Relief" on page...
... relief. Note: DO NOT plug in range at this time. The range can be converted using the LP conversion kit. Installation 7. Tighten all male pipe threads to relight the pilot on other gas appliances when you turn the gas back on. The gas connection is located below the back panel of DuPont English 16 1.Teflon is shipped from the back of the range. See "Install Strain Relief" on page...
Installation Instructions
Page 19
Use a backup wrench on the internal thread of opening . 2. Measure back left corner of the manual shutoff valve. 3. Install male 1/2" flare adaptor at gas inlet valve. Plug in the Off position. Adjust Leveling Legs 1. Adjust leveling leg until this height is off and then plug range cord into electrical outlet. 2. English 17 Connect flexible metal appliance connector. Make sure circuit breaker is the same as the corner dimension. 4. Line up range in...
Use a backup wrench on the internal thread of opening . 2. Measure back left corner of the manual shutoff valve. 3. Install male 1/2" flare adaptor at gas inlet valve. Plug in the Off position. Adjust Leveling Legs 1. Adjust leveling leg until this height is off and then plug range cord into electrical outlet. 2. English 17 Connect flexible metal appliance connector. Make sure circuit breaker is the same as the corner dimension. 4. Line up range in...
Installation Instructions
Page 20
... the back of the range must not rest on the countertop. Remove drawer and oven door to crimp flexible connector. To prevent damage to cooktop when sliding into Opening 1. CAUTION: Verify that the left leg is under the anti-tip bracket, slide range out, adjust legs and slide back in. Slide range into opening . 3. Be careful not to prevent damage 3. Note: When replacing a free-standing model, the backwall trim strip should not be...
... the back of the range must not rest on the countertop. Remove drawer and oven door to crimp flexible connector. To prevent damage to cooktop when sliding into Opening 1. CAUTION: Verify that the left leg is under the anti-tip bracket, slide range out, adjust legs and slide back in. Slide range into opening . 3. Be careful not to prevent damage 3. Note: When replacing a free-standing model, the backwall trim strip should not be...
Installation Instructions
Page 21
... stub. The gas connection is level and plumb. 4. Connect to regulator here Pipe Nipple Union Elbow E Gas Shut Off Valve F 1/2" to verify that the cooktop trim rests snugly against the countertop all the way around. 2. English 19 Verify that anti-tip bracket engages and pre- vents tip-over. Use a level to 3/4" Gas Pipe Figure 22: Rigid Pipe Method The configuration of Range for Proper Installation Installation 1. Rigid Pipe Method Adjust Front of...
... stub. The gas connection is level and plumb. 4. Connect to regulator here Pipe Nipple Union Elbow E Gas Shut Off Valve F 1/2" to verify that the cooktop trim rests snugly against the countertop all the way around. 2. English 19 Verify that anti-tip bracket engages and pre- vents tip-over. Use a level to 3/4" Gas Pipe Figure 22: Rigid Pipe Method The configuration of Range for Proper Installation Installation 1. Rigid Pipe Method Adjust Front of...
Installation Instructions
Page 22
... in power cord. 2. If the range does not slide easily, use soapy water to cooktop when sliding into Opening 1. however, the weight of the range will rest lightly on the countertop. drawer wrench adjustable leg Figure 23: Adjust the Front Leveling Leg 5. Plug in right back corner. 6. Note: When replacing a free-standing model, the backwall trim strip should not be sure all controls are in front of opening , being careful not to...
... in power cord. 2. If the range does not slide easily, use soapy water to cooktop when sliding into Opening 1. however, the weight of the range will rest lightly on the countertop. drawer wrench adjustable leg Figure 23: Adjust the Front Leveling Leg 5. Plug in right back corner. 6. Note: When replacing a free-standing model, the backwall trim strip should not be sure all controls are in front of opening , being careful not to...
Installation Instructions
Page 23
..., test is complete. Wipe off supply line gas shutoff valve and tighten connections. 5. Note: Be careful not to apply pressure to warming drawer element during installation. 3. Include gas fittings and joints in this section. The range will sit 3/4" away from the wall when properly installed. 5. CAUTION: Never check for leaks. Leak testing is not under the anti-tip bracket. Inspect for leaks with a flame. CAUTION: Verify that the...
..., test is complete. Wipe off supply line gas shutoff valve and tighten connections. 5. Note: Be careful not to apply pressure to warming drawer element during installation. 3. Include gas fittings and joints in this section. The range will sit 3/4" away from the wall when properly installed. 5. CAUTION: Never check for leaks. Leak testing is not under the anti-tip bracket. Inspect for leaks with a flame. CAUTION: Verify that the...
Installation Instructions
Page 24
... low setting: 1. Installation Test the Installation Turn on power at the breaker and return to self-clean. Push down and turn knob to the flame symbol until the burner ignites. 2. It should not go out, lift or blow off power at breaker Test self-clean lock Test Rangetop Burners: CAUTION: If the display flashes and beeps, the polarity of the burners do not light. Verify that the burner lights within four (4) seconds. Immediately switch off...
... low setting: 1. Installation Test the Installation Turn on power at the breaker and return to self-clean. Push down and turn knob to the flame symbol until the burner ignites. 2. It should not go out, lift or blow off power at breaker Test self-clean lock Test Rangetop Burners: CAUTION: If the display flashes and beeps, the polarity of the burners do not light. Verify that the burner lights within four (4) seconds. Immediately switch off...