BenQ LU9715 Support and Manuals
Get Help and Manuals for this BenQ item
Popular BenQ LU9715 Manual Pages
User Manual - Page 3
... Storing the projector...58 Specifications...59 Dimension...60 Timing chart...61 3D supported timing...62 RS232 command control 63 Control the projector through network 74 Set up the projector for networking 74 Control the projector through web browser 75 Projector status...75 Projector control...76 Crestron RoomView...76 Network setup...78 Alert mail setup...79 Troubleshooting...80 Indicator...
User Manual - Page 5
... with any parts of barrenness. WARNING! Please remember to qualified service personnel. CE...Manual carefully to obtain the best performance.The Manual provides instructions to unplug from electrical discharge or electric shock, do not open the cabinet.There are high-voltage components inside units. CAUTION To prevent electric shock, do not expose the projector to avoid problems...
User Manual - Page 6
... containing multiple laser diodes acts as Class 3R during all procedures of operation. • LASER LIGHT -
Laser safety notification and caution
• CLASS 3R LASER PRODUCT • This Laser Product is operated in which case the user will be hazardous to replace the light module. • Contact distributor who provides the qualified service for
maintenance or repair services of...
User Manual - Page 10
... fall over, causing injury or resulting in a safe place for your guide through this quality BenQ projector. Please read through the control menus and operation.
1. Always place the projector on end vertically. Do not place the projector in any of air around the projector is your purchase of more than 10 degrees left to fall and...
User Manual - Page 22
... setup and portability.
3. Purchase the BenQ Projector Ceiling Mount Kit from the ceiling behind the screen. This is selected. It is required to dissipate heat. Rear Table: Select this location with the projector placed near the floor in an environment where extreme temperature occurs. Contact your projector on the ceiling.
*Set Ceiling Front after you install the projector...
User Manual - Page 33
... the following guides to bring up the Lens Shift window.
2. Press the LENS SHIFT key on the projector in any direction or LENS SHIFT key on the remote control to adjust Picture Position manually. English
Using the menus
The projector is equipped with multilingual On-Screen Display (OSD) for making various adjustment and settings.The...
User Manual - Page 44
Laser B2/B3 Temp. English
Main menu Information
Model Serial Number Software Version BenQ Firmware Version Active Source Pixel Clock Signal Format H/V Refresh Rate Light Source Usage
Reset to Default Setting
Sub-menu BenQ Projector W332AFHCY001 MP05-0D06-.... 1.00 VGA 13.50 MHZ NTSC H: 15.736 KHZ V: 60 HZ
Inlet Ti1/Ti2 Temp. Outside Temp. DMD Temp. FAN...
User Manual - Page 49
... sync. 3D Swap: Set 3D Swap to ITU-R BT.601. Please remember: • People with the following options to use specific color space instead: Auto: The projector switches to Frame Sequential....sent to Side by Side manually. Those under six years old - Please refer to the guidelines publicized by Side (Half): Set 3D format to the projector through digital transmitter. Side by...
User Manual - Page 52
...Throw Lens is installed, make sure the support kit is set to Custom Power Level mode. High Altitude You can to ensure that the projector memorizes the exact lens settings.
• Light Settings.... English
Type setting is correct before performing Center Lens.
• Digital Zoom
Picture
Display
Setup \ Digital Zoom Digital Zoom Digital Pan Digital Scan
Setup
Advanced
System
Information...
User Manual - Page 56
...network settings till the following message disappears. English
Picture
Display
System \ Network Network Mode IP Address Subnet Mask Gateway DHCP Apply
Setup
Advanced
System Information
Projector ...Set up IP address of being entered manually. This function may have a 2-3 second lag before powering up . Otherwise, the domain does not or cannot assign an IP address, and 0. 0. 0. 0 is set...
User Manual - Page 57
... Displayport 74.1B4 MHz 1080i/60Hz H: 33.750 KHz V: 60.00 Hz 00047 HRS
Reset to Default Setting
Displayport
MENU Exit
Display basic information of the projector. • Model
Projector model number. • Serial Number
Projector serial number. • Software Version
Version of software installed in the projector. • BenQ Firmware Version
Version of firmware installed in System OSD.
User Manual - Page 59
Specifications
Model
Display Device
Input Terminals
Output Terminals
Resolution
HDMI ... (VESA mini din)
3G-SDI Out
Control and Service
Lan (RJ-45)
Wired Remote (φ3.5mm stereo min jack)
RS-232
Power Requirement
Input Current
Power Consumption (Normal Mode)
Operation Temperature
Storage Temperature
Dimensions Net Weight (Projector Only)
LU9715 Single Chip 0.67" DLP Technology
WUXGA 1 1...
User Manual - Page 74
...instead of having to be manually entered. Apply Network
Yes
No
Please contact your network administrator if the network remains disconnected.
74 English
Control the projector through network
Set up the projector for networking
Picture
Display
System \ Network Network Mode IP Address Subnet Mask Gateway DHCP Apply
Setup
Advanced
System Information
Projector Contorl
Off
Reset Network...
User Manual - Page 80
... Ready to alert users about problems with your nearest authorized dealer or service center. Wait until the projector starts projecting.
The LEDs on the control panel.
80 TEMP LED
LED display Off
Flashing
Red
Projector status
Operation tips
Normal status
Over temperature error
Contact with setup or system error. Call the local service center. POWER LED indicator
LED...
User Manual - Page 81
... the OSD. For example, if you take when troubleshooting: The information may encounter while using the projector. Keep a record of the steps you replace batteries and the problem remains, put the original batteries back and go to the next step. Check the following before proceeding to the problem-specific solutions.
• Use some other electrical device...
BenQ LU9715 Reviews
We have not received any reviews for BenQ yet.