BenQ HT3560 Support and Manuals
Get Help and Manuals for this BenQ item
BenQ HT3560 Videos
BenQ New HT4550i, HT3560, TK860i And V5000i 4K Projector Launched - Explained All Spec, Features
Duration: 2:46
Total Views: 152
Duration: 2:46
Total Views: 152
AVRant Podcast #860 - The Curse of Dr. Toole! (Disney+ ASL, BenQ TK860i, HT3560, HT4550i & V5000i)
Duration: 2:04:21
Total Views: 674
Duration: 2:04:21
Total Views: 674
Popular BenQ HT3560 Manual Pages
RS232 Control Guide - Page 3
...
Pin
Description
Pin
Description
1
NC
2
RXD
3
TXD
4
NC
5
GND
6
NC
7
RTS
8
CTS
9
NC
3
Follow the procedures to complete the connection and settings first, and refer to control your BenQ projector via RS232 from a computer. Check the specifications and user manual of the purchased projector for RS232 commands. Available functions and commands vary by...
RS232 Control Guide - Page 10
...will echo Illegal format. • If a command with correct format is not valid for the projector model, it will echo Unsupported
item. • If a command with correct format cannot be executed under ... features differ by projector specification, input sources, settings, etc.. • Commands are working if the standby power is 0.5W or a supported baud rate of characters are identical with .
RS232 Control Guide - Page 22
...=value#
YES
Read
Get Saturation value *saturation =?#
YES
Write
Gain +
*gain=+#
YES
Write
Gain -
*gain=-#
YES
Write
Set Gain value
*gain=value#
YES
Read
Get Gain value
*gain=?#
YES
Write
Color Gamut Auto
*cgamut=auto#
NO
Write
Color...#
YES
Write
Color Calibration
*colorpattern=value# YES
pattern display
Note: The above function will be varied from model to model.
22
User Manual - Page 11
... turning on the projector, go to position the projector for quick setup and portability.
2. Positioning your projector in the following factors into ...down from your special rear projection screen and the BenQ
dealer to select a setting. Positioning your projector
Choosing a location
Before choosing an installation location for your projector, take the following ways.
1. Note that a ...
User Manual - Page 18
...and switch to enter a 6-digit password. The projector will run the cooling fan for approximately 90 seconds before
energizing the lamp. • The Setup Wizard screenshots are prompted for 3 ... compatible with the projector's resolution or set the input signal to select your desired input signal. If you will display Source menu. See Utilizing the password function on page 21.
• ...
User Manual - Page 19
...you use the projector (after finishing the initial setup), Basic OSD menu displays. Below is equipped with On-Screen Display (OSD) menus for making various adjustments and settings. • Basic OSD menu: provides primary ...you may differ from the Basic OSD menu to the Advanced OSD menu, follow the instructions below are for reference only, and may access the Advanced OSD menu by pressing ...
User Manual - Page 20
... the second press closes the OSD menu. System > Menu Settings and press OK. 2. Select Menu Type and OK. 3. System > Firmware Upgrade menu and press OK.
5. Go to use the USB flash drive with FAT32 format)
SERVICE MEDIA READER
AUDIO OUT
SPDIF
3. Select Yes to select Basic. Upgrading firmware
1. In the process of the Advanced OSD menu...
User Manual - Page 24
...Picture Mode
The projector is no equipment connected to the signal type selected and the projector model you can choose one valid signal. See User Management on page 37.
24 Menu ... and deepest contrast at lower brightness level, Cinema mode is enabled.
• User: Recalls the settings customized based on -screen display (OSD) menus vary according to the projector or no signal detected,...
User Manual - Page 25
... Shows the current 3D mode. • Color System: Shows the used . • Firmware Version: Shows the firmware version of your projector. • Service Code: Shows the projector's serial number. when the value is higher, the image becomes brighter; ...Advanced menu on page 15. The projector can also manually select a brightness level to the input source. Switches to the Advanced OSD menu.
User Manual - Page 29
...when the value is higher, the image becomes brighter; Light Source Mode
See Setting the Light Source Mode on page 37. Reset Current Returns all of hue ... for optimal viewing.
• Motion Enhancer 4K
You can dim the dark parts of your image according to fine-tune the saturation of contrast ratio. It ... can also manually select a brightness level to -life images that pop off the screen.
User Manual - Page 31
... way by presenting the depth of the images. If the projector cannot recognize the 3D format, manually choose a 3D mode according to your preference.
• 3D Sync Invert When your 3D image...3D format when detecting 3D contents. On the Source Rename page, use / / / , and OK to set the image's aspect ratio depending on your desired name. When done, press BACK to your input signal source. ...
User Manual - Page 32
... RGB 16-235. • Full: Utilizes the Full range RGB 0-255. • HDMI Equalizer
Sets a suitable value to maintain the HDMI picture quality in long distance data transmission.
• HDMI EDID...• Enhanced: Enhanced mode can switch to HDMI 2.0 EDID (support 4K 60Hz HDR/HDR+) • Standard: Standard mode can set the behavior of powering on the Display menu to solve compatibility issue...
User Manual - Page 34
...can turn off the LED warning lights. Updates the projector firmware via USB reader.
34 Menu operation Background Settings
• Splash Screen Allows you purchased ...set period of time to obtain optimal picture quality from
whom you to Android TV dongle (QS02). This is password protected and only accessible by an ISF
certified installation technician. Accordingly, we recommend that setup...
User Manual - Page 39
... service ...instructions to avoid electric shock. Please also refer to the product user manual for 10 minutes to ensure power-off progress completely to ensure a safe lamp replacement...service technician to replace the lamp of your dealer or go to replace the lamp. Replacing the lamp (FOR SERVICE PERSONNEL ONLY)
Please consult your projector. Remove the safety mylar.
5. Please seek support...
User Manual - Page 47
...
1920X1200_120 (Reduce Blanking)
119.909
152.404
317.00
V
3840 x 2160
3840 x 2160_30 For 4K2K model
30
67.5
297
3840 x 2160_60
3840 x 2160
For 4K2K model (Only HDMI 2.0
60
135
594
support)
• ▲: support auto-detect 3D and manually set 3D format
Side by Side
▲ ▲ ▲
Color Depth Table
Display format (refresh rate...
BenQ HT3560 Reviews
We have not received any reviews for BenQ yet.