Installation Guide
Page 2
...) connector. 68-pin internal LVD/SE connector 68-pin external LVD/VHDCI connector Although the Adaptec SCSI Card 29320LP is a single channel SCSI card with 64- INTRODUCTION The Adaptec SCSI Card 29320LP enables you connect single-ended Wide Ultra/Ultra SCSI devices to the same SCSI channel as very large arrays of high-performance hard disk drives, external storage subsystems, Ultra320/160...
...) connector. 68-pin internal LVD/SE connector 68-pin external LVD/VHDCI connector Although the Adaptec SCSI Card 29320LP is a single channel SCSI card with 64- INTRODUCTION The Adaptec SCSI Card 29320LP enables you connect single-ended Wide Ultra/Ultra SCSI devices to the same SCSI channel as very large arrays of high-performance hard disk drives, external storage subsystems, Ultra320/160...
Installation Guide
Page 3
If the computer does not have a 64-bit slot, you turn off your computer). STEP 2 After you can install the card in Step 4. The Adaptec SCSI Card 29320LP supports both 5V and 3.3V 64-bit slots. (The expansion slot must be compliant with PCI Rev. 2.1 or PCI-X Rev. ...3 Locate an unused 64-bit PCI/PCI-X expansion slot and remove the expansion slot cover. INSTALLING THE ADAPTEC SCSI CARD 29320LP STEP 1 Discharge any static electricity build-up before handling your SCSI card by touching a grounded metal object (like the exposed metal parts on the back of your computer and unplug...
If the computer does not have a 64-bit slot, you turn off your computer). STEP 2 After you can install the card in Step 4. The Adaptec SCSI Card 29320LP supports both 5V and 3.3V 64-bit slots. (The expansion slot must be compliant with PCI Rev. 2.1 or PCI-X Rev. ...3 Locate an unused 64-bit PCI/PCI-X expansion slot and remove the expansion slot cover. INSTALLING THE ADAPTEC SCSI CARD 29320LP STEP 1 Discharge any static electricity build-up before handling your SCSI card by touching a grounded metal object (like the exposed metal parts on the back of your computer and unplug...
Installation Guide
Page 4
... with the expansion slot, as shown below. 3 press down firmly until the card clicks into the slot. If your computer manual to allow for easier installation of the Adaptec SCSI Card 29320LP. Insert the Adaptec SCSI Card 29320LP in a PCI slot. WARNING Be careful when inserting the Adaptec SCSI Card 29320LP in the 64-bit (or 32-bit) PCI or PCI-X expansion slot...
... with the expansion slot, as shown below. 3 press down firmly until the card clicks into the slot. If your computer manual to allow for easier installation of the Adaptec SCSI Card 29320LP. Insert the Adaptec SCSI Card 29320LP in a PCI slot. WARNING Be careful when inserting the Adaptec SCSI Card 29320LP in the 64-bit (or 32-bit) PCI or PCI-X expansion slot...
Installation Guide
Page 5
... cable, or the end of the cable (with a permanent terminator) or with jumpers; The Adaptec SCSI Card 29320LP is set with a separate terminating connector. Terminate the Ends To ensure reliable communication on an LVD Ultra320/160 and Ultra2 SCSI bus, the SCSI devices will not operate properly. Folowing are some guidelines for specific instructions. For this...
... cable, or the end of the cable (with a permanent terminator) or with jumpers; The Adaptec SCSI Card 29320LP is set with a separate terminating connector. Terminate the Ends To ensure reliable communication on an LVD Ultra320/160 and Ultra2 SCSI bus, the SCSI devices will not operate properly. Folowing are some guidelines for specific instructions. For this...
Installation Guide
Page 6
...cables are laminated so that you connect a legacy SCSI hard disk drive to the Adaptec SCSI Card 29320LP LVD/SE connectors, the Ultra320/Ultra160 and Ultra2 SCSI hard disk drives will slow to connect your Ultra SCSI devices. Internal LVD cables usually have either twisted ...Before connecting devices, be sure to connect internal Ultra320/160 or Ultra2 SCSI devices. The Adaptec SCSI Card 29320LP has one internal LVD/SE connector to the Adaptec SCSI Card 29320LP. CONNECTING SCSI DEVICES You can connect a total of 15 SCSI devices to which may have a terminator built into the end of...
...cables are laminated so that you connect a legacy SCSI hard disk drive to the Adaptec SCSI Card 29320LP LVD/SE connectors, the Ultra320/Ultra160 and Ultra2 SCSI hard disk drives will slow to connect your Ultra SCSI devices. Internal LVD cables usually have either twisted ...Before connecting devices, be sure to connect internal Ultra320/160 or Ultra2 SCSI devices. The Adaptec SCSI Card 29320LP has one internal LVD/SE connector to the Adaptec SCSI Card 29320LP. CONNECTING SCSI DEVICES You can connect a total of 15 SCSI devices to which may have a terminator built into the end of...
Installation Guide
Page 7
STEP 3 Plug the internal Ultra320/160 and Ultra2 SCSI devices to the other cable connectors, starting with termination disabled and cannot be changed. Proper termination is provided by the terminator at the terminated end of the LVD SCSI cable. 6 Ultra320/160 or Ultra2 SCSI devices Plug first device Built-in terminator to the internal LVD/SE connector. STEP 2 Plug the nonterminated end of the cable(s) to this connector on cable NOTE Internal Ultra320/160 and Ultra2 SCSI devices come from the factory with the connector at the end of the cable.
STEP 3 Plug the internal Ultra320/160 and Ultra2 SCSI devices to the other cable connectors, starting with termination disabled and cannot be changed. Proper termination is provided by the terminator at the terminated end of the LVD SCSI cable. 6 Ultra320/160 or Ultra2 SCSI devices Plug first device Built-in terminator to the internal LVD/SE connector. STEP 2 Plug the nonterminated end of the cable(s) to this connector on cable NOTE Internal Ultra320/160 and Ultra2 SCSI devices come from the factory with the connector at the end of the cable.
Installation Guide
Page 8
... steps to connect your computer's internal power supply to each internal SCSI device. If you are installing only one end of an external SCSI cable to the external Ultra320/160 connector on the Adaptec SCSI Card 29320LP. 68-pin external LVD/VHDCI SCSI connector VHDCI external LVD SCSI cable STEP 2 Connect the other end of the cable to...
... steps to connect your computer's internal power supply to each internal SCSI device. If you are installing only one end of an external SCSI cable to the external Ultra320/160 connector on the Adaptec SCSI Card 29320LP. 68-pin external LVD/VHDCI SCSI connector VHDCI external LVD SCSI cable STEP 2 Connect the other end of the cable to...
Installation Guide
Page 9
...sure to use a single-ended, active terminator (sometimes called an Ultra terminator) the SCSI devices will not operate properly. 8 If you are automatically unterminated, but Ultra SCSI and Fast/Wide SCSI devices do have termination that you use an LVD terminator to the documentation for all ...external device(s) and to the previous one, as shown below. STEP 4 Terminated SCSI device Connect power cables to all other external SCSI devices by linking each SCSI bus cable must be terminated, and termination must check. For more information, refer to terminate the...
...sure to use a single-ended, active terminator (sometimes called an Ultra terminator) the SCSI devices will not operate properly. 8 If you are automatically unterminated, but Ultra SCSI and Fast/Wide SCSI devices do have termination that you use an LVD terminator to the documentation for all ...external device(s) and to the previous one, as shown below. STEP 4 Terminated SCSI device Connect power cables to all other external SCSI devices by linking each SCSI bus cable must be terminated, and termination must check. For more information, refer to terminate the...
Installation Guide
Page 10
...Adaptec SCSI Card 29320LP was included as part of the driver software varies depending on each SCSI bus have embedded driver support for help. ADAPTEC SCSI CARD DRIVER SOFTWARE NOTE To use the Adaptec SCSI Card 29320LP, driver software must be installed for information. 9 No further action is supported by the computer manufacturer. TROUBLESHOOTING If you have any problems while installing the Adaptec SCSI Card 29320LP..., check the following items first: •Are all SCSI devices powered on? •Are all SCSI cables and power cables...
...Adaptec SCSI Card 29320LP was included as part of the driver software varies depending on each SCSI bus have embedded driver support for help. ADAPTEC SCSI CARD DRIVER SOFTWARE NOTE To use the Adaptec SCSI Card 29320LP, driver software must be installed for information. 9 No further action is supported by the computer manufacturer. TROUBLESHOOTING If you have any problems while installing the Adaptec SCSI Card 29320LP..., check the following items first: •Are all SCSI devices powered on? •Are all SCSI cables and power cables...
Installation Guide
Page 11
... could void the user's authority to comply with the instruction manual, may be registered in a particular installation. Copyright © 2002 Adaptec, Inc. assumes no guarantee that to which the receiver is subject to radio communications. This equipment has been tested and found to ... the equipment to provide reasonable protection against harmful interference in accordance with the limits for information only and is connected. Trademarks Adaptec, and the Adaptec logo are designed to an outlet on , the user is no liability resulting from errors or omissions in this unit not...
... could void the user's authority to comply with the instruction manual, may be registered in a particular installation. Copyright © 2002 Adaptec, Inc. assumes no guarantee that to which the receiver is subject to radio communications. This equipment has been tested and found to ... the equipment to provide reasonable protection against harmful interference in accordance with the limits for information only and is connected. Trademarks Adaptec, and the Adaptec logo are designed to an outlet on , the user is no liability resulting from errors or omissions in this unit not...
Installation Guide
Page 12
...meets all equipment requiring U.L. This device complies with part 15 of the Canadian Interference-Causing Equipment Regulations. Japanese Compliance (Voluntary Control Council Initiative) This equipment complies to the Australian/New Zealand standard AS/NZS 3548 set out by 93/68/EEC in... interference and (2) this documentation. 11 EN61000-4-5 (1995) Surges ±1 kV differential mode, ±2 kV common mode - Adaptec SCSI Card 29320LP Tested to Comply With FCC Standards FOR HOME OR OFFICE USE European Union Compliance Statement This Information Technology Equipment has been tested and...
...meets all equipment requiring U.L. This device complies with part 15 of the Canadian Interference-Causing Equipment Regulations. Japanese Compliance (Voluntary Control Council Initiative) This equipment complies to the Australian/New Zealand standard AS/NZS 3548 set out by 93/68/EEC in... interference and (2) this documentation. 11 EN61000-4-5 (1995) Surges ±1 kV differential mode, ±2 kV common mode - Adaptec SCSI Card 29320LP Tested to Comply With FCC Standards FOR HOME OR OFFICE USE European Union Compliance Statement This Information Technology Equipment has been tested and...