Lexmark E260 Support Question
Lexmark E260 Support Question
Find answers below for this question about Lexmark E260.Need a Lexmark E260 manual? We have 5 online manuals for this item!
Question posted by vsTer on June 13th, 2014
How To Reset Lexmark E260 Chip
The person who posted this question about this Lexmark product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Lexmark E260 Manual Pages
Service Manual - Page 16
...and recommendations to identify the connector locations and test points on the printer. 6.
xvi Lexmark™ E260, E260d, E260dn It is a danger from hazardous voltage in order...hazard. 4513-200, -220, -230
Preface
This manual contains maintenance procedures for making printer adjustments and removing and installing
FRUs.
5.
Parts catalog contains illustrations and part numbers ...
Service Manual - Page 17
... E460dw, see the 4513-420,-430 service manual. For information on page 4-1 to determine the symptom and repair the failure.
General information 1-1 For information on E260, E260d and E260dn. General information
The Lexmark™ E260, E260d, and E260dn are monochrome laser printers designed for more information.
Service Manual - Page 24
... & Label Guide available on the 250-sheet tray before pushing the tray into the printer.
• Make sure paper guides are positioned before loading it. The following tools and... nose pliers • Volt-ohmmeter • #1 and #2 Phillips screwdriver • Slotted screwdriver
1-8 Lexmark™ E260, E260d, E260dn Have excessive curl - 4513-200, -220, -230
Most paper jams can help prevent...
Service Manual - Page 28
... fuser) and then stays on.
4. See
"Common primary light patterns" on momentarily 2. Lights then flash on , it performs a POST. The printer cycles down into standby mode, and lights solid.
2-2 Lexmark™ E260, E260d, E260dn 4513-200, -220, -230
Overview of the operator panel
Paper jam light
Toner light
Error light
Load paper light...
Service Manual - Page 30
...Unsupported Flash Option Installed
Cancel job
10
Reset printer
Restore factory defaults
Invalid engine code
11
Invalid network code
Resolution reduced while
11
&#...13
Printer error³
13
2-4 Lexmark™ E260, E260d, E260dn
Service Manual - Page 32
...220, -230
Common light sequences when replacing the photoconductor
Printer Condition
Page
Replace photoconductor
12
(printer hard stop)
Ready and Replace Photoconductor/Power Save and Replace...
x
2 -6 Lexmark™ E260, E260d, E260dn
Service Manual - Page 34
... Continue to print the contents of the print buffer. • Press and release Cancel to cancel the print job. • Press and hold Cancel to reset the printer.
2-8 Lexmark™ E260, E260d, E260dn The Ready light is waiting until a print timeout occurs, or until it receives additional data.
Hex Trace Ready
x Meaning The...
Service Manual - Page 36
... job. • Press Cancel to the user default settings. The printer will automatically reset.
Cancel job/Reset printer/Restore factory defaults
Meaning
• The current print job is canceled.
• The printer is too full to clear.
2-10 Lexmark™ E260, E260d, E260dn 4513-200, -220, -230
Close door or insert...
Service Manual - Page 38
... to print a photoconductor kit instruction page. • Replace the photoconductor kit.
2-12 Lexmark™ E260, E260d, E260dn Action
• Press and release Continue to clear the light sequence and continue...new toner cartridge that matches the region of the installed toner cartridge.
The printer will not print any more pages until the photoconductor kit is almost full and...
Service Manual - Page 40
... to resume printing once all the jammed pages are cleared from the output bin. • Press Continue to reset the printer.
2-14 Lexmark™ E260, E260d, E260dn Load media in Tray 1 or Tray 2
Meaning
The printer is full.
Remove paper from output bin
Meaning The output bin is out of print media...
Service Manual - Page 42
... are both on, a paper jam has occurred with a
Printer Condition
Page
200: Paper jam at the input
18
sensor
...61548;
2-16 Lexmark™ E260, E260d, E260dn The following table shows what these light sequences mean and where to display the secondary error code light sequence. 4513-200...
Service Manual - Page 44
... the input sensor, which can be either after the print media leaves the tray and enters the printer or in the fuser area under the toner cartridge assembly. Action
Open the front door, remove the... rear)
Meaning
The media did leave the printer exit sensor.
Action
Open the rear door, and clear the paper jam.
2-18 Lexmark™ E260, E260d, E260dn
Service Manual - Page 46
...).
Complex page
Meaning
The page may be lost). 4513-200, -220, -230
251: Paper jam in the Local Printer Setup Utility. • Install additional printer memory.
2-20 Lexmark™ E260, E260d, E260dn
Action
• Press Continue to On in the manual feeder
Meaning
A paper jam has occurred...
Service Manual - Page 48
...Insufficient defrag memory
Meaning
The printer memory does not have enough memory to reset the printer. To avoid this error in the buffer. Reduce the complexity...the page and deleting unnecessary downloaded fonts or macros.
• Install additional printer memory.
2-22 Lexmark™ E260, E260d, E260dn
Action
Add more memory than the set page margins. ...
Service Manual - Page 56
...
Service watchdog: 90x
901: Timer service slow
2-30 Lexmark™ E260, E260d, E260dn For the other errors, which indicate a faulty programming process or faulty component on page 4-6. Note: All service errors ...in an intermittent condition when POR (power-on reset) is performed which allows the printer to perform the task.
Service Manual - Page 74
... Wait Timeout Auto Continue Jam Recovery Page Protect Print Area
Job Menu Cancel Job Reset Printer Print Buffer
Quality Menu Print Resolution Toner Darkness PictureGrade™
PPDS Menu Orientation Lines... PS SmartSwitch NPA Mode USB Buffer Mac Binary PS
2-48 Lexmark™ E260, E260d, E260dn 4513-200, -220, -230
Diagram of the printer menus
Not all menus or selections will be available on all...
Service Manual - Page 86
... at its ends. If the toner cartridge is being used .
Variation in the printer driver.
2-60 Lexmark™ E260, E260d, E260dn Place a sheet of damage or fatigue. Replace the transfer roll... should support the transfer roll, applying evenly distributed forces to make sure that the laser light path is being used . Check the media settings in image density horizontally across...
Service Manual - Page 88
...Light or blurred characters. With the printer off , clear the path or clean the lens.
Vertical white lines may be caused by the laser beam, which may be incorrectly set...or defect.
Vertical streaks
Something could be partially blocked. Replace the PC kit.
2-62 Lexmark™ E260, E260d, E260dn Check those settings. Vertical white lines
See "Vertical streaks below. Vertical white...
Service Manual - Page 96
...turn off the printer. 2.
Help isolate printing problems when unexpected characters print or characters are reset to help evaluate print quality:
• A text page with printer information, cartridge...only when the photoconductor kit has been replaced.
3-4 Lexmark™ E260, E260d, E260dn Print menus by providing information about what the printer is blank.
4513-200, -220, -230
...
Service Manual - Page 176
... front access cover 4-6 procedures 4-2
Reset Factory Defaults 3-4 reset maintenance page counter 3-4 Reset PC Counter 3-4
S
safety information xiii safety inspection guide 6-1 service checks 2-51
controller card 2-51 cooling fan 2-52 cover interlock switch 2-52 dead machine 2-53 fuser 2-53 LVPS/HVPS 2-54 main motor 2-54 operator panel 2-55
I-2 Lexmark™ E260, E260d, E260dn
paper feed 2-55...
Similar Questions
Lexmark Ms711 Laser Printer Weight
what does the ms711 laser printer weigh without additional trays?
what does the ms711 laser printer weigh without additional trays?
(Posted by cathyrose2 10 years ago)
My Lexmark C534dn Color Laser Printer Has Red And Yellow Smudge Down Each Side
My Lexmark C534dn color laser printer has red and yellow smudge down each side of the page. On the l...
My Lexmark C534dn color laser printer has red and yellow smudge down each side of the page. On the l...
(Posted by amjohau 12 years ago)