Hitachi C10RA3 Support Question
Hitachi C10RA3 Support Question
Find answers below for this question about Hitachi C10RA3 - 10 Inch Portable Table Saw.Need a Hitachi C10RA3 manual? We have 1 online manual for this item!
Question posted by benjaminrondon on January 23rd, 2021
What Kind Of Dado Blade Is Suitable For The C10ra3 Table Saw
The person who posted this question about this Hitachi product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by hzplj9 on January 27th, 2021 11:00 AM
hzplj9
Member since:
June 25th, 2012 Points: 4,873,510
Member since:
June 25th, 2012 Points: 4,873,510
The user guide:
https://www.hikokipowertools.com/manual_view_export/pdf/C99150063_C10RA3_605.pdf
Refer to page 21 of the pdf file for information on Dado blades.
Hope that helps.
Related Hitachi C10RA3 Manual Pages
Instruction Manual - Page 3
...or damage to a 110-120 Volt / 15 Ampere time delay fuse or circuit breaker. This table saw is critical that are :
• Lead based paints • Crystalline silica from bricks, cement...of work with Extension ......... 24-1/2" Blade Size 10" Rip Scale YES Rip Fence YES Miter Gauge YES Maximum Cut Depth @ 90 3" Maximum Cut Depth @ 45 2-1/2" Maximum Dado Cut Width 1/2" Net Weight 58...
Instruction Manual - Page 4
... a complete stop.
17. MAINTAIN TOOLS WITH CARE. English
POWER TOOL SAFETY
WARNING
Before using your table saw . DO NOT OVERREACH. Keep proper footing and balance at the rate for alignment of moving parts, binding of the blade or cutter only.
- 4 - KEEP WORK AREA CLEAN. DISCONNECT TOOLS before the blade comes to the tool.
15. READ and become familiar...
Instruction Manual - Page 5
... from the interior of the saw blade.
15. NEVER REACH behind or over the cutting tool for making your hands out of the saw to the saw blade. For proper operation follow the...THE SAW RUNNING UNATTENDED. PROVIDE ADEQUATE SUPPORT to a complete stop.
10. Do not leave the saw until the blade comes to the rear and the sides of your table saw on page 11.
17. Through-sawing operations ...
Instruction Manual - Page 6
...
Not More Than 25ft. 50ft. 100ft. 150ft.
0
6
18 16 16 14
6
10
18 16 14 12
10
12
16 16 14 12
12
16
14 12 Not Applicable
GUIDELINES FOR EXTENSION CORDS
Any ... this tool. DO NOT MODIFY THE PLUG PROVIDED. This power tool is connected to a known ground.
2-Prong Receptacle
Before connecting the saw , use the next heavier gauge cord. The table above . It is in the table above shows...
Instruction Manual - Page 7
...: • Do not use accessories
not recommended by Store.
TABLE OF LOOSE PARTS
ITEM DESCRIPTION
QUANTITY
A Table saw assembly
1
B Blade guard and splitter
1
C Rip fence
1
D Dado table insert
1
E Miter gauge
1
F Blade wrench
2
G Hand wheel
2
H Blade
1
I Hex wrench
1
J Guard mounting bolt,flat washer, 1 each part with this saw , plug in the power cord, or turn the...
Instruction Manual - Page 9
English
KNOW YOUR JOBSITE TABLE SAW
Table
Blade guard Miter gauge
Table insert Rip fence
Side table extension
Blade tilt scale Blade tilt pointer
Hand hold Blade bevel lock knob
Overload reset switch ON/OFF switch with key
Blade elevation handwheel Bevel tilting handwheel
Stand
Cord wrap
Rear Of The Table Saw
Rip fence and miter gauge storage
- 9 -
Instruction Manual - Page 10
... the table saw by the spinning blade. Tilts the blade to 45° for bevel cuts. The shaft on which a blade is set from wood products. Leading Edge Kerf
Surface
Saw Blade Path
...saw motor if it overheats or overloads. The surfaces of the blade. WOODWORKING TERMS
ARBOR -
Workpiece
Trailing Edge
- 10 - A guide used for changing blades. MITER CUT - ANTI-KICKBACK PAWLS -
BLADE...
Instruction Manual - Page 11
... the plug is
provided under rear of the saw . Unfold the leg sets and push down handwheel (1) to the maximum height by removing the two screws (2, 3). If the rear of the insert
is not level with the table. Remove the table insert (1) by turning the blade raising handwheel counterclockwise.
3. Be careful not to lose...
Instruction Manual - Page 12
...) must be under the rear of the insert and leveling the rear of the table).
9. Lift blade guard arm (8) up and using a dado blade.
Fig. NOTE: The blade guard and splitter is properly aligned with the teeth pointing toward the front of the saw arbor to the table. G flat washer (3), external tooth lock washer (4) onto the...
Instruction Manual - Page 13
... 90°(00) to the table. I
Anti-kickback Pawl
8 10
9
Straight edge
ADJUSTING THE 90°(00) AND 45° POSITIVE STOPS (FIG.
J, K, L) Your saw has positive stops that will quickly position the saw from the power source. 2. Make adjustments only if necessary.
90°(00) Stop 1. If the blade is 45° to the...
Instruction Manual - Page 14
...3
STORAGE (FIG. O-1)
WARNING
Do not wrap the cord around the dust port.
Raise the blade to right side: 1. Above the table. 5. M
2
counterclockwise, then adjust the right side screw(3) clockwise. 2.
Remeasure, as described...are 8 mm. Remeasure, as described in steps 4 to left side of the saw housing.
N) NOTE: The adjusting nuts are not the same. When alignment is ...
Instruction Manual - Page 15
... square to the groove, do the following : • Loosen the two screws (3) and lift up on the saw table. Lower the front end onto the front rail (3). 3. P) 1. P
1
MITER GAUGE ADJUSTMENT (FIG. Loosen...at 0º, 15º, 30º, 45º, 60º both right and left side. Blade (Fig. Replace the knob
and tighten. Fig. Q) 1. MITER GAUGE OPERATION (FIG. The operate the...
Instruction Manual - Page 16
... of the table saw. T-1
ADJUSTING CAM LOCKING LEVER (FIG. To adjust the locking lever tension, turn the bar (2) with accuracy up to align to the side of an inch. T-1) The table extension scale pointer (1) should be loose and need adjustment, therefore, adjustment to the cam locking lever is the distance from the blade to 1/16...
Instruction Manual - Page 17
..., and then tighten the bevel lock handle (2) to the ON position. X
2 1
USING THE TABLE EXTENSION (FIG.
To turn the saw will not operate. 5. Fig. English
OPERATION
BASIC SAW OPERATIONS
RAISE THE BLADE (FIG. Fig.
X) The ON / OFF switch has a removable safety key. Y)
WARNING
To prevent fire hazard, clean and remove sawdust from the...
Instruction Manual - Page 18
... the workpiece.
To make an additional push stick, use of the table. 10.Never pull the piece back when the blade is in place and working properly. 5. Continue pushing the workpiece with... locked into the blade by pushing forward on the section of the workpiece.
4. Keep your
table saw ON and wait for the blade to come to the miter gauge groove. 4. Raise the blade so it is ...
Instruction Manual - Page 19
... on the left side groove.
1. Select a suitable piece of plywood to 1in. When cutting long workpieces, you are provided in the right side groove (2) because the bevel angle may cause the blade guard to interfere with screws. The miter gauge (1) must be ripped and your table
saw to cause careless mistakes.
Always use one...
Instruction Manual - Page 20
... flush or recessed.
The miter gauge (3) must be used on the saw table without rocking.
3-1/2"
Fig. Set the blade (1) to the desired angle. 2. Fig. Set the blade (1) bevel to shape and size shown: Putting it toward the blade, the blade guard may cause the blade guard to shape and size shown: Making the side: • Start...
Instruction Manual - Page 21
... on this saw blade, original table inser and blade guard. Attach auxiliary fence to rip fence with the dado operation.
- 21 - WARNING
For your own safety, always replace the blade, blade guard assembly, and blade insert when you are finished with two "C" clamps. (Fig. When making full 1/2 in the dado set . 3. Always use caution when operating a dado blade. 6. Use only...
Instruction Manual - Page 22
....
5. NOTE: Certain cleaning chemicals can damage plastic parts.
6. Maximum allowable play in place. Tighten nut (2) with the wrench, while holding nut (3)
in the blade raising screw (1) should be adjusted as would oil or grease. English
MAINTENANCE
MAINTAINING YOUR TABLE SAW
Fig. LL
GENERAL MAINTENANCE
WARNING
For your table saw table with pitch and gum remover. 4.
Instruction Manual - Page 69
...HD. NECK BOLT CAP HD. English
PARTS LIST
10" JOBSITE TABLE SAW
PARTS LIST FOR SCHEMATIC
HKU# 726434 726437 325693 ... ARBOR COLLAR SUPPORTING PLATE PARRLE RING BLADE HEX WRENCH FLAT WASHER FLAT WASHER ...C-RING HEX. C10RA3
Size
QTY
1
1
1
1
1
1
1
1
#23
1
#23
1
1
2
1
1
2
1
2
1
1
1
1
1
1
1
1
φ5*10-1
4
φ6*13-1
1
φ8X16-2.5
1
φ10*30-0.2
2
...
Similar Questions
That's The Original Hitachi Japonês?
I'm looking for hitachi miter saw 10" japonês original not the metabo you guys have
I'm looking for hitachi miter saw 10" japonês original not the metabo you guys have
(Posted by Pereirafulr 2 years ago)
What Size Is The Thin Inner Arbor Wrench On The C 10 Ra3
(Posted by windowsheeter 3 years ago)
Hitachi C10ra3 Compatible Blades.
Can I use an 8 inch blade with this saw? If so, can it be for cutting ceramic tile?
Can I use an 8 inch blade with this saw? If so, can it be for cutting ceramic tile?
(Posted by gwoltman 3 years ago)
Blade Removal
How do you secure the saw blade to remove and what direction is the nut thread?
How do you secure the saw blade to remove and what direction is the nut thread?
(Posted by nbergeson 12 years ago)
Changing Saw Blade
Where are instructions on changing a saw blade on a Hitachi C8FSE saw? Thanks
Where are instructions on changing a saw blade on a Hitachi C8FSE saw? Thanks
(Posted by weishapple 12 years ago)