Hitachi C10RA3 Support Question
Hitachi C10RA3 Support Question
Find answers below for this question about Hitachi C10RA3 - 10 Inch Portable Table Saw.Need a Hitachi C10RA3 manual? We have 1 online manual for this item!
Question posted by windowsheeter on November 3rd, 2020
What Size Is The Thin Inner Arbor Wrench On The C 10 Ra3
The person who posted this question about this Hitachi product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by Odin on November 4th, 2020 10:57 AM
Odin
Member since:
April 10th, 2010 Points: 41,236,690
Member since:
April 10th, 2010 Points: 41,236,690
If you mean the two accessory wrenches included with the product, Hitachi does not document that information but warns, "The use of any other attachment or accessory can be dangerous." Chances are you could obtain replacements from Hitachi at nominal or no cost. Use the contact information at https://www.contacthelp.com/htachi/customer-service.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Hitachi C10RA3 Manual Pages
Instruction Manual - Page 3
... with Extension ......... 24-1/2" Blade Size 10" Rip Scale YES Rip Fence YES Miter Gauge YES Maximum Cut Depth @ 90 3" Maximum Cut Depth @ 45 2-1/2" Maximum Dado Cut Width 1/2" Net Weight 58.3 LBS
WARNING
To avoid electrical hazards, fire hazards or damage to filter out microscopic particles. This table saw , use proper circuit protection...
Instruction Manual - Page 4
....
10. MAINTAIN TOOLS WITH CARE. ALWAYS wear safety goggles (not glasses) that is recommended. Failure to the tool.
15. LEARN the tool's applications, limitations and possible hazards.
2.
DO NOT wear loose clothing, gloves, neckties, rings, bracelets or other conditions that identifies important safety precautions. DISCONNECT TOOLS before the blade comes to the table saw...
Instruction Manual - Page 5
... or over the cutting tool for additional sawdust removal.
19. FEED WORK INTO THE BLADE against the miter gauge or rip fence.
3. Attach a vacuum to move into the saw table for long or wide workpieces... the fence.
14. NEVER use either the fence or the miter gauge to a complete stop.
10. Failure to provide sawdust fall-through and removal hole will allow sawdust to prevent a potential fi...
Instruction Manual - Page 6
... 100ft. 150ft.
0
6
18 16 16 14
6
10
18 16 14 12
10
12
16 16 14 12
12
16
14 12 Not ... saw is turned OFF.
- 6 -
If it . IMPROPER CONNECTION of the equipment grounding conductor can result in the table above shows the correct size... the cord. NOTE: The 12 to the table saw is the equipment grounding conductor. Protect your tools. DO NOT MODIFY THE PLUG PROVIDED.
The ...
Instruction Manual - Page 7
... head set with this saw assembly
1
B Blade guard and splitter
1
C Rip fence
1
D Dado table insert
1
E Miter gauge
1
F Blade wrench
2
G Hand wheel
2
H Blade
1
I Hex wrench
1
J Guard mounting bolt,flat washer, 1 each part with a clean dry cloth. TOOLS NEEDED FOR ASSEMBLY
Supplied
Not Supplied
Wrench Wrench 3 mm Hex Wrench
Medium Screwdriver #2 Phillips screwdriver...
Instruction Manual - Page 9
English
KNOW YOUR JOBSITE TABLE SAW
Table
Blade guard Miter gauge
Table insert Rip fence
Side table extension
Blade tilt scale Blade tilt pointer
Hand hold Blade bevel lock knob
Overload reset switch ON/OFF switch with key
Blade elevation handwheel Bevel tilting handwheel
Stand
Cord wrap
Rear Of The Table Saw
Rip fence and miter gauge storage
- 9 -
Instruction Manual - Page 10
... a bevel cut , to the blade arbor for rip cutting that has hardened. BLADE TILTING HANDWHEEL - Resets the thermocouple and provides a way to 45° for crosscutting operations that will be straight.
A guide used for bevel cuts.
SET -
The surfaces of the workpiece. The amount of the table saw blade tips, bent outward in...
Instruction Manual - Page 11
... of insert for this purpose.
1. Raise the blade arbor (4-Fig. F) and place the box-end wrench (9) on the back screw (3) beneath the table insert. (Fig. Remove the table insert (1) by turning the blade raising handwheel counterclockwise.
3. Attach and tighten the dome nut (5-Fig.C)
2
Fig. Position the saw to lower the insert, turn the screw
1
counterclockwise...
Instruction Manual - Page 12
...H) until parallel alignment to the blade is flush againstthe inner side of table in place. Shift the splitter bracket assembly to right or left ...and leveling the rear of the saw . 6. H
7
6. Install the flange (6) against the blade and thread the
arbor nut (5) as far as possible by hand. Place the box-end wrench (9) on the bevel scale with the saw blade (10). (Fig. G, H, I )...
Instruction Manual - Page 13
...
8 10
9
Straight edge
ADJUSTING THE 90°(00) AND 45° POSITIVE STOPS (FIG. Turn the blade elevation handwheel and raise the
blade to the maximum vertical position, then tighten the lock knob (1). 4. L) 4. Adjust the collar (5) so it contacts the bracket (3) when the blade is 45° to the table. Disconnect the saw...
Instruction Manual - Page 15
...;, 15º, 30º, 45º, 60º both right and left side. Fig. Place extra blades onto the arbor. Fig. Make a 90º cut to lock.
- 15 -
4
2 Q) The miter gauge is snug. R ...to the groove, do the following : • Loosen the two screws (3) and lift up on the saw table. Lower the front end onto the front rail (3). 3. Blade (Fig. Q) 1. Check
the cut in...
Instruction Manual - Page 16
...INDICATOR (FIG. Take off the cover (1) by the indicator will provide the user with a 10 mm wrench until it is a difference between the measurement and the indicator, adjust the indicator as shown ...cam locking lever (1) may be at 13.5 inches on the front of the table saw. Adjust the pointer (3) to align to fix the pointer. T-1) The table extension scale pointer (1) should be loose and ...
Instruction Manual - Page 18
... base of a second is enough to the arbor. 2. Remember that even a careless fraction of the saw ON and wait for the blade to come to...passes through the blade guard and clears the rear of the table. 10.Never pull the piece back when the blade is tightened to ... the workpiece away from the path of the workpiece. Keep your
table saw each and every time, check the following:
1. When the blade...
Instruction Manual - Page 19
...the blade guard to 45°, the miter gauge handle will cause kickback and serious injury to obtain the size of plywood to an angle other than 0º. CC 1
3
2
USING WOOD FACING ON THE MITER ...if used on .
5.
Fig. The miter gauge (1) must be ripped and your table
saw blade path, always stand to avoid instability.
- 19 - EE
32
1
WARNING
Always position the larger surface of ...
Instruction Manual - Page 20
...& straight 3/4 in position by tightening the miter gauge locking handle.
3. Attach the wood facing to shape and size shown: Making the side: • Start with the cut . II) Making the base: • Start...1
USING WOOD FACING ON THE RIP FENCE (FIG. Fig. The bottom must be used on the saw table without rocking.
3-1/2"
Fig. WARNING
Always work at least 5-1/2 in
wide or wider and 30 in...
Instruction Manual - Page 21
... 1/2 in . 7. English
2 1 3 Blade or chipper must not exceed 1/2 in or less. Check saw to ensure that at least one thread of round outside flange (2) before screwing on this saw blade, original table inser and blade guard.
The arbor (1) on the arbor nut (3). It will not strike the housing, insert, or motor when in the...
Instruction Manual - Page 22
... These dry lubricants will not hold sawdust as follows: 1. Using a wrench, loosen nut (2). 2. Tighten nut (2) with the wrench, while holding nut (3)
in the blade raising screw (1) should be ...the switch OFF and remove the switch key. English
MAINTENANCE
MAINTAINING YOUR TABLE SAW
Fig. Avoid use of cleaning chemicals or solvents, ammonia and household detergents containing ammonia....
Instruction Manual - Page 23
....
2. Splitter not aligned with adequate size cord. 2.
Fuse blown or circuit breaker tripped. 2. Warped wood, edge against fence is not tight.
7.
Gum or pitch on flat level surface. Change the blade.
5. Damaged saw blade.
Cord damaged.
3.
Check and align splitter with turpentine and steel
feed. Clean table with blade. Sawdust and dirt...
Instruction Manual - Page 24
English
PUSH STICK CONSTRUCTION ● This is a full-size drawing (actual size) ● Use good quality plywood or solid wood ● Use 1/2 in . Wood
- 24 -
Wood
Cut Here To Push 3/4 in . or 3/4 in . material ● Push stick MUST be thinner than the width
of material being cut
Drill Hole For Hanging
Notch To Prevent Hand From Slipping
Cut Here To Push 1/2 in .
Instruction Manual - Page 69
...HD. NECK BOLT CAP HD. SQ. C10RA3
Size
QTY
1
1
1
1
1
1
1
1
#23
1
#23
1
1
2
1
1
2
1
2
1
1
1
1
1
1
1
1
φ5*10-1
4
φ6*13-1
1
φ8X16-2.5
1
φ10*30-0.2
2
φ12*21-1
2
...MODEL NO. TAPPING SCREW HEX. RE. NUT HEX. English
PARTS LIST
10" JOBSITE TABLE SAW
PARTS LIST FOR SCHEMATIC
HKU# 726434 726437 325693 726438 726439 726440 726441 ...
Similar Questions
That's The Original Hitachi Japonês?
I'm looking for hitachi miter saw 10" japonês original not the metabo you guys have
I'm looking for hitachi miter saw 10" japonês original not the metabo you guys have
(Posted by Pereirafulr 2 years ago)
Hitachi C10ra3 Compatible Blades.
Can I use an 8 inch blade with this saw? If so, can it be for cutting ceramic tile?
Can I use an 8 inch blade with this saw? If so, can it be for cutting ceramic tile?
(Posted by gwoltman 3 years ago)
I Can Adjust The Mitre Angle All The Way On The Right But It Stops At 10 Degrees
I can adjust the mitre angle all the way on the right but it won't budge past 10 degrees when I try ...
I can adjust the mitre angle all the way on the right but it won't budge past 10 degrees when I try ...
(Posted by rivuletcottage 9 years ago)
How To Adjust Cut Depth Hitachi 10 Compound Miter Saw Manual
(Posted by dbrag 9 years ago)
Switch Handle Broken Off. Cannot Operate Saw.
I need the entire switch handle housing for Hitachi 10" Slide Compound Saw, Model# C10FS, serial# W6...
I need the entire switch handle housing for Hitachi 10" Slide Compound Saw, Model# C10FS, serial# W6...
(Posted by bob02909 10 years ago)