Craftsman 22124 Support Question
Craftsman 22124 Support Question
Find answers below for this question about Craftsman 22124 - Professional 10 in. Table Saw.Need a Craftsman 22124 manual? We have 1 online manual for this item!
Question posted by fberdyck on October 9th, 2020
Does It Operate On 120 Or 220 Current
The person who posted this question about this Craftsman product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Craftsman 22124 Manual Pages
Owners Manual - Page 1
..., IL 60179 U.S.A. OR91552 Revision: D
Espa5ol pg. 48 Customer Helpline
1-800-897-7709
Please have your Model No. Read and follow all of the Safety and Operating Instructions before Operating this Table Saw. Owner's
uai
CRRFrSMRH
1.75 Horsepower (continuous duty) 2.4 Horsepower (maximum developed) 3450 R.P.M. (no load...
Owners Manual - Page 2
... Center for 120V, 60 Hz, operation.
Table Saw
Motor type Continuous duty HP Maximum developed HP Amps Volts Hertz
induction 1.75 2.4 15/7.5 120/240 60
RPM Blade tilt
3450 ...R.RM. (no load R.RM.) Left tilt
Blade drive Blade diameter Blade arbor Number of teeth
Poly-V Belt 10-in. 5/8-in .
To avoid electrical shock to yourself and damage to the Table Saw...
Owners Manual - Page 4
...
wax.
19. Turn the power switch to a complete stop.
16. BEFORE USING THE TABLE SAW
9. DO NOT leave the tool until it .
18. DO NOT use the tool for which could result if the tool tips over the tool. GENERAL SAFETY iNSTRUCTiONS
Operating a Table Saw can be dangerous if safety and common sense are slippery from debris, grease, and...
Owners Manual - Page 6
...Table Saw is shipped wired for use on the junction box cover. The motor supplied with ALL local codes and ordinances. REPLACE A DAMAGED OR WORN CORD IMMEDI= ATELY. This tool is necessary. THiS ADAPTER iS PROHIBITED iN CANADA. THiS TOOL MUST BE GROUNDED WHILE iN USE TO PROTECT THE OPERATOR...for electric current and reduces the risk of the electric cord or plug is intended for 120 volts ...
Owners Manual - Page 7
... to replace the 120 volt plug, supplied with the motor, with a UL/CSA Listed plug suitable for 240 volts and rated current of this machine.
4. This Table Saw is for proper procedures to an outlet having the same configuration as a toy.
Keep your eyes, which can result in Figure "1C". DO NOT OPERATE THiS MACHINE...
Owners Manual - Page 8
... off the table/work area before table saw blade when using auxiliary fence as a stop when cross-cutting.
32. Refer to them to the power source.
33. Information regarding the safe and proper operation of this ...ADDiTiONAL iNFORMATiON regarding the safe and proper operation of this tool is available from the following sources:
Power Tool Institute 1300 Summer Avenue Cleveland, OH ...
Owners Manual - Page 9
...
32371
Sears may cause serious injury and cause damage to the table saw .
Featherboards are finished. Dado
29885
* Table Insert - Molding Cutterhead * Saw Blade - Use only accessories recommended for this manual. Always replace the guard and splitter assembly when the non-through cutting operations where the guard and splitter assembly must be straight piece of...
Owners Manual - Page 11
... assembly. This may need redone several times before assembly.
8, Compare the items to any parts are required to unpack and lift the table saw. If there are removed completely. Fence hook (2)
10. Dust Port 13. After cleaning, apply a good quality paste wax to figures below; verify that all the parts have been obtained...
Owners Manual - Page 16
... certain assembly operations. hex wrench
13mm wrench 10mm wrench
#2 Phillips screwdriver #3 Phillips screwdriver
8mm wrench 1/2-in .
two people are needed for assembly and alignment. See figure 4-1.
2.
DUST PORT ASSEMBLY
MAKE CERTAIN the table saw to the floor, DO NOT assemble leveling feet and go on each of the cabinet. See figure 4-1.
3. TOOLS REQUIRED
The...
Owners Manual - Page 18
... and a 13mm wrench on flats of the cabinet and tighten securely. See figure 10-2 and 10-3.
1. Figure 10=2
C_
....... Align the groove (C) in the rear of the handwheel with the pin (D). Figure 8=2
E
BLADE GUARD AND SPLITTER ASSEMBLY
MAKE CERTAIN the table saw is disconnected from the power source. 1. WRENCH AND FENCE HOOK ASSEMBLY
MAKE CERTAIN...
Owners Manual - Page 19
...10-6.
6. Replace table insert and tighten table insert retaining bolt removed in the Operations and Adjustments section of the splitter bracket knob (G); See figure 10-4. make sure the teeth of the splitter bracket assembly. Figure 10=3
\ C
4. See figure 10-3.
5. Place the front attachment point (D) of the blade guard and splitter assembly (H) down in the
front of the table saw table...
Owners Manual - Page 25
... the motor cover (F) and remove the two Phillip head screws (G) from the table saw (B). Mark the floor through the holes in the four bottom corner brackets (L).
9. Attach the table saw out of the way and drill pilot holes at the four locations marked.
10. Remove the four leveling feet (A) from the CRAFTSMAN nameplate (H). NOTE: These...
Owners Manual - Page 26
...tools and debris before starting table saw beyond its capacity, or low voltage) press the "OFF" button and let the motor cool three to insure that the electric current is located under the front rail on the table saw will damage the motor. To use the table saw...your table saw off during an operation (cutting a workpiece too fast or using a dull blade, using the saw . When the table saw . ...
Owners Manual - Page 28
... cabinet. Make sure the rule is disconnected from the outer diameter.
MAKE CERTAIN the table saw blade to the miter slots, it becomes necessary (see "ADJUSTING BLADE ALIGNMENT." Figure 17=1 ... (A) on the front of the blade to check the alignment before initial operation as follows:
MAKE CERTAIN the table saw blade. If an adjustment is recommended to the miter slots. This means when...
Owners Manual - Page 29
... to the miter slot, first loosen two hex head screws (A) under the left side of the table saw table is now loose and can be necessary to hold the lock handle in "CHECKING BLADE AMGNMENT."
4. Make.... 17B=1
®
[ BIESEMEYER
BIESEMEYER ® T=SQUARE ® COMMERCIAL RiP FENCE SYSTEM ASSEMBLY OPERATIONS AND ADJUSTMENTS
A B
To align the blade parallel to lock the rip fence. The...
Owners Manual - Page 31
...arbor to 240-volt operation for current of the motor. Two wrenches are supplied with 5/8-in the opposite direction from power source.
2. Replace blade guard and splitter
31 Oncetheinsertis level,securetheinsertwiththe retainingboltremovedinstep1.
5. CHANGING MOTOR VOLTAGE
• MAKE CERTAIN the table saw table and assemble the blade flange and arbor nut. Replace 120 volt plug with a UL...
Owners Manual - Page 32
...angle between plus or minus 45-degrees or it can extend tool life 25% to standard saw is disconnected from the power source when making adjustments. To rotate...10=INCH VARIABLE TOOTH SAW BLADE
Key features of blade (D) and adjust the front splitter bracket to the human ear.
4. A lOdB is disconnected from the power source. MITER GAUGE OPERATION AND ADJUSTMENT
MAKE CERTAIN the table saw...
Owners Manual - Page 33
... 22-2.
6, Place a square against the saw blade and miter gauge body. See figure 23...10. To adjust O-degree positive stops, loosen knob, pull out on trigger (C) and hold. If the fence stop angle to quickly position the clamp up on plunger and turn knob (E) to desired position and tighten hex socket head screw. Figure 22=2
G D
CLAMP AND FENCE STOP OPERATION
MAKE CERTAIN the table saw...
Owners Manual - Page 35
... has come to a complete stop.
See figure 25-1. Affter the workpiece is not touched until the saw blade and anti-kickback fingers, you can continue to the end of the table, after which the workpiece is the operation of making narrow cuts. Oncethecut-offlengthis determinedlo, ckthe
fenceandslidetheworkpieceacrossthetable surfaceuntilit contactstheblock.Usethe miter gauge(K)to...
Owners Manual - Page 41
...
OR91074
117
OR91118
118
OR91078
Description
OWNER'S MANUAL - #22124 10" TaNe Saw
BLADE GUARD ASSEMBLY, (NOT SHOWN) CONSISTS OF REF #: 1,2, 3,...SET SCREW 1/4-28 x 3/8", NYLOCK TABLE INSERT- PART No.
119 120 121 122 123 124 125 126... 127 127A 128 129 130 131 132 133 134 134A 135 136 2B0 201 2B2 2B3 2B3A 204 205 206 2B7 2B8 209 210B 211 212 213 214 215 216 217 218 220...
Similar Questions
Arbor Nut For A Craftsman Professional Table Saw
(Posted by jimszawara 6 months ago)
Is There Any Place You Know Of Where I Can Get The Table Saw Arbor Nut #or91050?
Any hints would be appreciated
Any hints would be appreciated
(Posted by Chuckmorley 1 year ago)
Changing Table Saw Motor To 240v
I have a 10" Craftsman table saw model #152221140. Lost the cover to the wiring which has the diagra...
I have a 10" Craftsman table saw model #152221140. Lost the cover to the wiring which has the diagra...
(Posted by mridude 9 years ago)
What Is A Sears Electronic 10'table Saw Worth
what is a sears electronic 10" table saw w/ext,& base model 113.290650 worth?, it works great
what is a sears electronic 10" table saw w/ext,& base model 113.290650 worth?, it works great
(Posted by mastercook76 11 years ago)
Need Wiring Diagram For 71/2 Craftman Table Saw-mdl 113.24151
(Posted by darent 12 years ago)