Craftsman 21237 - 10 in. Sliding Miter Saw Support and Manuals
Get Help and Manuals for this Craftsman item
View All Support Options Below
Free Craftsman 21237 manuals!
Problems with Craftsman 21237?
Ask a Question
Free Craftsman 21237 manuals!
Problems with Craftsman 21237?
Ask a Question
Most Recent Craftsman 21237 Questions
What Is The Horsepower Of The 6 Speed Shift On The Go Model No. 247.290001
(Posted by Anonymous-153718 8 years ago)
How To Mount A Miter Saw
(Posted by tjsmosg 9 years ago)
Model 171 Router Will Not 'lock On'
The "lock on" button does not lock the on/off trigger in place
The "lock on" button does not lock the on/off trigger in place
(Posted by egmears 10 years ago)
How Do I Adjust My Craftsman 10' Bandsaw Blade 214 Model
(Posted by Dougdavid 11 years ago)
What Is A Sears Electronic 10'table Saw Worth
what is a sears electronic 10" table saw w/ext,& base model 113.290650 worth?, it works great
what is a sears electronic 10" table saw w/ext,& base model 113.290650 worth?, it works great
(Posted by mastercook76 11 years ago)
Popular Craftsman 21237 Manual Pages
Operation Manual - Page 1
SLiDiNG COMPOUND MITER SAW WiTH LASER TRAC ® Model No. 137.212370
CAUTION:
Before using this Miter Saw, read this manual and follow all its Safety Rules and Operating instructions
• Safety Instructions • installation
• Operation • Maintenance e Parts List
Customer Help Line For Technical Support
1-800-843-1682
Sears Parts & Repair Center 1-800-488-1222
Sears, ...
Operation Manual - Page 2
...
7
SECTION
Know Your Sliding Compound Miter Saw .....
Bevel 45 ° L 1-&/8 in . S ECTION
PAG E
Warranty
2
Product Specifications
2
Power Tool Safety
3
Sliding Compound Miter Saw Safety
4
Electrical Requirements and Safety
4
Accessories and Attachments
6
Tools Needed for 110=120 Volt operation. To avoid shock or fire, replace power cord immediately if...
Operation Manual - Page 4
... before resuming operation.
[,_ WARNING J POWER SUPPLY AND MOTOR SPECIFICATIONS The AC motor used in this tool. DO NOT operate the miter saw is completely assembled and installed according to the blade when the saw is worn or cut metals or masonry products with this saw until it replaced immediately.
4 MAKE SURE the blade is sharp, runs freely...
Operation Manual - Page 5
...replace a damaged extension cord or have a certified electrician check the receptacle.
5 Before connecting the tool to start /stops in the OFF position and the electric current is double insulated to the TROUBLESHOOTING GUIDE...length.
Check the saw again. Use only identical replacement parts when
servicing a tool with protecting insulation:
Replacement parts - The saw blades are not...
Operation Manual - Page 7
... electric shock, use only identical replacement parts when servicing double insulated tools. Remove the miter saw , or plug in carrying handles located at the top of power during unpacking and assembly. Lift only by the switch handle or miter table handle. Check
each one with the illustration below to assemble the miter saw from the packing material. The...
Operation Manual - Page 9
... material removed by a spinning object in opposite directions to 45 ° left.
The amount of the workpiece.
Supports the table, holds accessories and allows for compact storage and transportation. COVER PLATE SCREW - The blade is released.
Locks the miter saw blade 0 ° to each other proper device to keep the blade from moving when...
Operation Manual - Page 10
... minutes
[,AWAR"I"GI
To avoid injury, do not connect this Operator's Manual.
IMPORTANT: To avoid damage, never carry the miter saw from the carton, loosen the slide carriage lock knob (1). ALWAYS use the stop latch to its lowest position. 2.
Fig. iNSTALLiNG THE MITER HANDLE (FIG.
B-l) 1. iNSTALLiNG THE DUST BAG (FIG. Place the dust bag neck opening around...
Operation Manual - Page 13
... and properly arranged. The saw blade path on for any contact with the base or the miter table by the transformed alternating current supply directly through the holes (2) in . Installing Blade (Fig. J) in place. When arbor lock engages, continue to show.
[A WARNIN] G
• AVOID DIRECT EYE CONTACT Laser radiated when laser guide is released so the...
Operation Manual - Page 16
... electrical parts do not work on the miter saw again. • Maintain tools with the accessory'.
Learn its application and limitations as well as the potential hazards specific to the direction arrow on . The lower guard should always point downward at the front of this Operator's Manual. (SEE SAFETY AND OPERATIONS SECTIONS)
• Reviewthe MAINTENANCE AND TROUBLESHOOTING GUIDE...
Operation Manual - Page 17
...parts.
o Do not use this miter saw to cut .
• Make sure there is longer or wider than the basic miter saw blades specifically...all applicable safety instructions when cutting non-ferrous metals: • Use only saw table, or...OR ODD SHAPED WORKPIECES
• Use extra supports (tables, sawhorses, blocks, etc.) for
...correct the problem.
17 Use a different tool for any miter saw to do ...
Operation Manual - Page 18
.... Fig. It will stop the blade within 6 seconds, unplug the saw and follow the instructions in TROUBLESHOOTING GUIDE section for the blade to stop . • Unplug the miter saw . Finishing a cut and releasing the trigger switch, allow the blade brake to replace the proper use of your saw ON. Never rely on it to activate and stop before...
Operation Manual - Page 22
.... Miter table set at RIGHT 31.6 ° .
22 _" The setup of molding against fence.
12.Miter table set at RIGHT 31.6 .
3. To fit properly, crown molding must be cut crown molding for the difficult task of crown molding that the settings are at 45 °
NOTE: Always perform a dry run cut . DD
Workpiece
F
e
Workpiece
Miter saw iabie q
Bevel/Miter Settings...
Operation Manual - Page 24
... up a miter cut.
GI
• To avoid fire or toxic reaction, never use only parts identical to avoid electrical shock. Reassemble exactly as the original assembly to those identified in the movement of carbon remaining, or ff the spring or wire is required. To inspect or replace brushes, first unplug the saw for the...
Operation Manual - Page 25
... on 3. TROU BLESHOOTING GUIDE - Miter table unlocked. 2. Loose pivot points.
I . Pivot spring not replaced properly
after service. 3. Sawdust build-up 1. See BASIC SAW OPERATION section.
2. Use hold down . [_ WARNING I To avoid injury from use of cut .
1. Motor does not start
I . Replace brushes.
5. Brush worn. 2.
Contact Sears Service Center. 3.
Retighten...
Operation Manual - Page 26
...MODEL.O137.212370
IA WARNINI G
When servicing use only CRAFTSMAN replacement parts. PARTS LIST FOR SAW...23N F
Description SLIDE PLATE TRIGGER
...parts many create a HAZARD or cause product damage. Any attempt to repair or replace electrical parts on this Miter Saw may create a HAZARD unless repair
is done by a qualified service technician, Repair service is available at your nearest Sears Service...
Craftsman 21237 Reviews
We have not received any reviews for Craftsman yet.