Owner's Manual
Page 11
...bus. Signals input to the L input (odd channel) go to the channel. NOTE The mixer's STEREO Master control has no affect on the Stereo L and R buses. As the knob is turned to the EFFECT (AUX) bus. The result is smoother, more even dynamics because louder signals are mixed and ...the amount of the three bands. C Level Control Adjusts the level of the channel signal on the signal output via the STEREO OUT jacks. MG82CX/MG102C Owner's Manual 11 On stereo channels (CHs 3/4 to 7/8 (CHs 3/4 to 9/10)) the signals from the channel to minimize noise. Note that ...
...bus. Signals input to the L input (odd channel) go to the channel. NOTE The mixer's STEREO Master control has no affect on the Stereo L and R buses. As the knob is turned to the EFFECT (AUX) bus. The result is smoother, more even dynamics because louder signals are mixed and ...the amount of the three bands. C Level Control Adjusts the level of the channel signal on the signal output via the STEREO OUT jacks. MG82CX/MG102C Owner's Manual 11 On stereo channels (CHs 3/4 to 7/8 (CHs 3/4 to 9/10)) the signals from the channel to minimize noise. Note that ...
Owner's Manual
Page 12
...to the PHONES jack and the MONITOR jacks. Devices other than condenser mics may be left on the mixer supplies +48V phantom power to the STEREO L/R buses. The "0" segment corresponds to an external effect unit. 5 STEREO OUT (L, R) Jacks These are sent to the MONITOR OUT jacks, the PHONES jack, and the ...-type MIC INPUT jacks. • Be sure to the STEREO L/R bus. NOTE When this switch is on the mixer supplies DC +48 V power to pins 2 and 3 of loud noises that output the signals adjusted by induced noise. 12 MG82CX/MG102C Owner's Manual We also recommend that outputs the signal ...
...to the PHONES jack and the MONITOR jacks. Devices other than condenser mics may be left on the mixer supplies +48V phantom power to the STEREO L/R buses. The "0" segment corresponds to an external effect unit. 5 STEREO OUT (L, R) Jacks These are sent to the MONITOR OUT jacks, the PHONES jack, and the ...-type MIC INPUT jacks. • Be sure to the STEREO L/R bus. NOTE When this switch is on the mixer supplies DC +48 V power to pins 2 and 3 of loud noises that output the signals adjusted by induced noise. 12 MG82CX/MG102C Owner's Manual We also recommend that outputs the signal ...
Owner's Manual
Page 13
... When you do not plan to use the mixer for the selected effect. NOTE The ON switch lights and the internal effect unit is active by default when the power is turned on. CAUTION MG82CX/MG102C Owner's Manual 13 An optional YAMAHA FC5 foot switch (sold separately) can be ... the internal digital effect unit to this switch is initially turned on. 5 EFFECT RTN Control Adjusts the signal level sent from the wall outlet. 2 AC ADAPTOR IN Connector ConnectConnect the supplied PA-10 power adaptor to the STEREO buses. 4 5 MG82CX Rear Input/Output Section 1POWER Switch Use this mixer.
... When you do not plan to use the mixer for the selected effect. NOTE The ON switch lights and the internal effect unit is active by default when the power is turned on. CAUTION MG82CX/MG102C Owner's Manual 13 An optional YAMAHA FC5 foot switch (sold separately) can be ... the internal digital effect unit to this switch is initially turned on. 5 EFFECT RTN Control Adjusts the signal level sent from the wall outlet. 2 AC ADAPTOR IN Connector ConnectConnect the supplied PA-10 power adaptor to the STEREO buses. 4 5 MG82CX Rear Input/Output Section 1POWER Switch Use this mixer.
Owner's Manual
Page 15
...MIC input jacks on channels 1 to the EFFECT (AUX) jack*. MG82CX/MG102C Owner's Manual 15 Mounting to a Microphone Stand • When using the mixer on a microphone stand, be damaged if...firmly into the mixer? ❑ Are microphones, external devices, and speakers connected correctly? ❑ Are the channel GAIN controls, LEVEL controls, STEREO Master control set to ...mixer right-side up the stand in brackets: MG82CX (MG102C). Attach the connection cables carefully so that they shorted? ❑ If the above checks do not identify the problem, call Yamaha...
...MIC input jacks on channels 1 to the EFFECT (AUX) jack*. MG82CX/MG102C Owner's Manual 15 Mounting to a Microphone Stand • When using the mixer on a microphone stand, be damaged if...firmly into the mixer? ❑ Are microphones, external devices, and speakers connected correctly? ❑ Are the channel GAIN controls, LEVEL controls, STEREO Master control set to ...mixer right-side up the stand in brackets: MG82CX (MG102C). Attach the connection cables carefully so that they shorted? ❑ If the above checks do not identify the problem, call Yamaha...